Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)

DTC    U0073    Control Module Communication Bus Off

DTC    U0100    Lost Communication with ECM / PCM "A"

DTC    U0101    Lost Communication with TCM

DTC    U0122    Lost Communication with Vehicle Dynamics Control Module

DTC    U0140    Lost Communication with Body Control Module

DTC    U0155    Lost Communication with Instrument Panel Cluster Control Module (Combination Meter)

DTC    U0401    Invalid Data Received from ECM/PCM "A"

DTC    U0422    Invalid Data Received from Body Control Module

for Preparation Click here


DESCRIPTION

These DTCs are stored when there is a CAN communication error between the certification ECU (smart key ECU assembly) and the ECM, TCM, main body ECU (network gateway ECU), combination meter assembly or brake actuator assembly (skid control ECU).

HINT:
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No.
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
U0073
CAN communication system malfunction (1-trip detection logic*).
CAN communication system
Turn the engine switch on (IG) and wait 10 seconds or more.
U0100
CAN communication malfunction between the certification ECU (smart key ECU assembly) and ECM (1-trip detection logic*).
ECM
Turn the engine switch on (IG) and wait 10 seconds or more.
U0101
CAN communication malfunction between the certification ECU (smart key ECU assembly) and TCM (1-trip detection logic*).
TCM
Turn the engine switch on (IG) and wait 10 seconds or more.
U0122
CAN communication malfunction between the certification ECU (smart key ECU assembly) and brake actuator assembly (skid control ECU) (1-trip detection logic*).
Brake actuator assembly (skid control ECU)
Turn the engine switch on (IG) and wait 10 seconds or more.
U0140
CAN communication malfunction between the certification ECU (smart key ECU assembly) and main body ECU (network gateway ECU) (1-trip detection logic*).
Main body ECU (network gateway ECU)
Turn the engine switch on (IG) and wait 10 seconds or more.
U0155
CAN communication malfunction between the certification ECU (smart key ECU assembly) and combination meter assembly (1-trip detection logic*).
Combination meter assembly
Turn the engine switch on (IG) and wait 10 seconds or more.
U0401
CAN communication malfunction between the certification ECU (smart key ECU assembly) and ECM (1-trip detection logic*).
ECM
Turn the engine switch on (IG) and wait 10 seconds or more.
U0422
CAN communication malfunction between the certification ECU (smart key ECU assembly) and main body ECU (network gateway ECU) (1-trip detection logic*).
Main body ECU (network gateway ECU)
Turn the engine switch on (IG) and wait 10 seconds or more.
*: Only output while a malfunction is present and the engine switch is on (IG)

Vehicle Condition and Fail-safe Function when Malfunction Detected 
DTC Code
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
U0073
There is no effect on vehicle behavior.
-
U0100
There is no effect on vehicle behavior.
If the following conditions are met, it is determined that the malfunction is not in the direct line (TACH) but in CAN communication.
  1. When the engine switch is pressed, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.
  2. When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.
If the following conditions are met, it is determined that there is a malfunction in both CAN communication and the direct line (TACH).
  1. When the engine switch is pressed, the engine stops cranking after 6 seconds.
  2. When the engine switch is pressed and held, the engine remains cranking for up to 30 seconds.
U0101
There is no effect on vehicle behavior.
-
U0122
There is no effect on vehicle behavior.
-
U0140
Doors cannot be locked or unlocked.
The warning (wireless buzzer) does not sound.
-
U0155
The warning (meter buzzer) does not sound and the meter does not indicate a warning.
-
U0401
There is no effect on vehicle behavior.
-
U0422
Doors cannot be locked or unlocked.
The warning (wireless buzzer) does not sound.
-

Related Data List and Active Test Items 
DTC
Data List Item
Active Test Item
U0073
U0100
U0101
U0122
U0140
U0155
U0401
U0422
-
-

INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off to troubleshoot:
    Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
  2. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

1.CHECK FOR DTC
  1. Note any DTCs that are output (Click here).


NEXT

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)