Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Driver Side Power Window does not Operate with Power Window Master Switch

for Preparation Click here


DESCRIPTION

When the engine is running or the ignition switch is ON, the power window regulator motor assembly is operated by the power window regulator master switch assembly. The power window regulator motor assembly has motor, regulator and ECU functions.

WIRING DIAGRAM


B311524E03


B311524E04


INSPECTION PROCEDURE

NOTICE:
  1. When the power window regulator master switch assembly, power window regulator switch assembly and power window regulator motor assembly is reinstalled or replaced, the power window control system must be initialized (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Master Switch / Active Test.

  1. Perform the Active Test according to the display on the GTS.

    Master Switch 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Driver side power window
    OFF / UP / DOWN
    -

    OK:
    Driver door power window operates normally.

    CAUTION:
    Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.

Result 
Result
Proceed to
NG
A
OK
B


B
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
A


2.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY)
  1. Disconnect the E8*1 or F6*2 power window regulator master assembly connector.



    B322620E01
  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E8-12 (+B)*1 - Body ground
    Always
    11 to 14 V
    F6-12 (+B)*2 - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-5 (GND)*1 - Body ground
    Always
    Below 1 Ω
    F6-5 (GND)*2 - Body ground
    Always
    Below 1 Ω

    1. *1: for LHD
    2. *2: for RHD

Text in Illustration 
*A
for LHD
*B
for RHD
*a
Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY)
  1. Disconnect the E8*1 or F6*2 power window regulator master switch assembly connector.

  1. Disconnect the E5*1 or F1*2 power window regulator motor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    E8-6 (WU) - E5-1 (WU)*1
    Always
    Below 1 Ω
    E8-7 (WD) - E5-3 (WD)*1
    Always
    Below 1 Ω
    F6-6 (WU) - F1-1 (WU)*2
    Always
    Below 1 Ω
    F6-7 (WD) - F1-3 (WD)*2
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    E8-6 (WU)*1 - Body ground
    Always
    Below 1 Ω
    E8-7 (WD)*1 - Body ground
    Always
    Below 1 Ω
    F6-6 (WU)*2 - Body ground
    Always
    Below 1 Ω
    F6-7 (WD)*2 - Body ground
    Always
    Below 1 Ω

    1. *1: for LHD
    2. *2: for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
  1. Temporarily replace the power window regulator master switch assembly with a new or normally functioning one (Click here).

  1. Check the power window regulator master switch assembly operates (Click here).

    OK:
    Driver side door power window operates normally.

Result 
Result
Proceed to
Operate
A
Does not operate
B


B
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (Click here)
A

END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WAS DEFECTIVE)