Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)

ENTRY AND START SYSTEM (for Entry Function) > Key Luggage Compartment Lock-in Prevention Function does not Operate

for Preparation Click here


DESCRIPTION

If the entry luggage compartment lock-in prevention function does not operate, there may be a problem with the communication between the No. 3 indoor electrical key oscillator (inside luggage) and electrical key transmitter sub-assembly, wave interference or a malfunction in the certification ECU (smart key ECU assembly).

WIRING DIAGRAM


B369630E02


INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
  2. The entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  3. Check that there are no electrical key transmitter sub-assemblies in the vehicle.
  4. Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).
  5. Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution (Click here).
  6. After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

1.CHECK ENTRY FUNCTION (ENTRY LUGGAGE COMPARTMENT OPEN FUNCTION)
  1. Check that the entry luggage compartment open function operates (Click here).

    Result:
    Result
    Proceed to
    Entry luggage compartment door open function operates
    A
    Entry luggage compartment door open function does not operate
    B



B
GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table) (Click here)
A


2.CHECK WAVE ENVIRONMENT


    B374551E01
  1. Bring the electrical key transmitter sub-assembly near the No. 3 indoor electrical key oscillator (inside luggage), and check that the entry luggage compartment lock-in prevention function operates.
    Text in Illustration 
    *1
    Electrical Key Transmitter Sub-assembly
    *a
    Inspection Point

    NOTICE:
    If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the No. 3 indoor electrical key oscillator (inside luggage), communication is not possible.

    HINT:
    1. When the electrical key transmitter sub-assembly is brought near the No. 3 indoor electrical key oscillator (inside luggage), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    OK:
    Entry functions operate normally.



NG
Go to step 3
OK

AFFECTED BY WAVE INTERFERENCE 

3.CHECK KEY DIAGNOSTIC MODE
B374551E01
  1. Check the following antennas in the key diagnostic mode (Click here).

Text in Illustration 
*1
Electrical Key Transmitter Sub-assembly
*a
Inspection Point
  1. When the electrical key transmitter sub-assembly is held at the same height as the rear bumper upper surface and aligned with the center of the rear of the vehicle, check that the wireless door lock buzzer sounds.

    HINT:
    1. Place the key in the luggage area.
    2. If the buzzer sounds, it can be determined that the No. 3 indoor electrical key oscillator (inside luggage compartment) is operating normally.

    OK:
    Wireless door lock buzzer sounds.



NG
Go to step 4
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR)
  1. Disconnect the D40 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the H9 No. 3 indoor electrical key oscillator (inside luggage) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D40-9 (CLG7) - H9-1 (ANTE7)
    Always
    Below 1 Ω
    D40-8 (CG7B) - H9-3 (CLGB)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D40-9 (CLG7) or H9-1 (ANTE7) - Body ground
    Always
    10 kΩ or higher
    D40-8 (CG7B) or H9-3 (CLGB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Connect the D40 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the H9 No. 3 indoor electrical key oscillator (inside luggage) connector.



    B282018E19
  1. Measure the voltage according to the value(s) in the table below.

OK:
Tester Connection
Switch Condition
Tool Setting
Specified Condition
H9-1 (ANTE7) - H9-3 (CLGB)
Procedure:
  1. Engine switch off
  2. Electrical key transmitter sub-assembly not inside vehicle
  3. All doors closed
  4. Driver door lock sensor not touched → touched
2 V/DIV., 500 ms/DIV.
Pulse generation (See waveform)

Text in Illustration 
*a
Front view of wire harness connector
(to No. 3 Indoor Electrical Key Oscillator (inside luggage compartment))
*b
Waveform
*c
Driver side door lock sensor not touched
*d
Driver side door lock sensor touched


NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


6.REPLACE NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR (INSIDE LUGGAGE)
  1. Replace the No. 3 indoor electrical key oscillator (inside luggage) with a new one (Click here).


NEXT


7.CHECK NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR (INSIDE LUGGAGE)
  1. Check that the entry luggage compartment lock-in prevention function operates normally (Click here).

    OK:
    Entry luggage compartment lock-in prevention function operates normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (NO. 3 INDOOR ELECTRICAL KEY OSCILLATOR WAS DEFECTIVE)