AIRBAG SYSTEM > SRS Warning Light Remains ON |

| 1.CHECK SRS WARNING LIGHT OPERATION |
Check the SRS warning light operation approximately 6 seconds after the ignition switch is turned to ON.
| SRS Warning Light Illumination | Proceed to |
| Remains on | A |
| Goes off and then comes on again | B |
|
| ||||
| A | |
| 2.CHECK BATTERY VOLTAGE |
Measure the voltage of the battery.
|
| ||||
| OK | |
| 3.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connector is properly connected to the airbag ECU assembly.
Disconnect the connector from the airbag ECU assembly.
Check that the terminal of the connector is not damaged.
|
| ||||
| OK | |
| 4.CHECK WIRE HARNESS (AIRBAG ECU ASSEMBLY - BODY GROUND) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D27-21 (IG) - Body ground | Ignition switch ON | 8 to 16 V |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D27-25 (GND) - Body ground | Always | Below 1 Ω |
| D27-26 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Airbag ECU Assembly) |
|
| ||||
| OK | |
| 5.CHECK SRS WARNING LIGHT |
Turn the ignition switch to ON.
Check the SRS warning light condition.
|
| ||||
| OK | ||
| ||
| 6.CHECK CAN COMMUNICATION SYSTEM |
Use the GTS to check if the CAN communication system is functioning normally.
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 7.CHECK BATTERY VOLTAGE |
Measure the voltage of the battery.
|
| ||||
| OK | |
| 8.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connector is properly connected to the airbag ECU assembly.
Disconnect the connector from the airbag ECU assembly.
Check that the terminal of the connector is not damaged.
|
| ||||
| OK | |
| 9.CHECK WIRE HARNESS (AIRBAG ECU ASSEMBLY - BODY GROUND) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D27-21 (IG) - Body ground | Ignition switch ON | 8 to 16 V |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D27-25 (GND) - Body ground | Always | Below 1 Ω |
| D27-26 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Airbag ECU Assembly) |
|
| ||||
| OK | |
| 10.CHECK CONNECTOR |
Disconnect the cable from the negative (-) battery terminal.
Check that the connector is properly connected to the combination meter assembly.
Disconnect the connector from the combination meter assembly.
Check that the terminal of the connector is not damaged.
|
| ||||
| OK | |
| 11.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D7-1 (B) - Body ground | Always | 11 to 14 V |
| D7-2 (IG+) - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D7-20 (ES1) - Body ground | Always | Below 1 Ω |
| D7-40 (ES2) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
|
| ||||
| OK | |
| 12.CHECK SRS WARNING LIGHT |
Disconnect the cable from the negative (-) battery terminal.
Connect the connector to the combination meter assembly.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Check the SRS warning light condition.
|
| ||||
| OK | ||
| ||