Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > DIAGNOSIS SYSTEM

for Preparation Click here



ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM
  1. V Bus

    1. Main body ECU (network gateway ECU)

    2. Combination meter assembly

    3. Certification ECU (smart key ECU assembly)*1

    4. ECM

    5. TCM*2

    6. Skid control ECU (brake actuator assembly)

    7. Steering angle sensor (spiral cable sub-assembly)

    8. Power steering ECU assembly

    9. Air conditioning control assembly*3

    10. Air bag ECU assembly

    11. PSP (option connector)
      *1: w/ Entry and Start System
      *2: for Automatic Transmission System
      *3: for Automatic Air Conditioning System


CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT ADOPT CAN COMMUNICATION
  1. The systems (ECUs and sensors) that adopt CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed on the vehicle.

    HINT:
    The names of ECUs and sensors shown on the GTS display may differ from those shown in the DTC Table by ECU section that follows.


    ECU/Sensor Name
    GTS Display
    Applicability
    Main body ECU (network gateway ECU)
    Main Body
    Installed on all vehicles
    Combination meter assembly
    Combination Meter
    Installed on all vehicles
    Certification ECU (smart key ECU assembly)
    Certification (Smart)
    w/ Entry and Start System
    ECM
    ECM (Engine)
    Installed on all vehicles
    TCM
    TCM
    for Automatic Transmission System
    Skid control ECU (brake actuator assembly)
    Skid Control (ABS/VSC/TRAC)
    Installed on all vehicles
    Steering angle sensor (spiral cable sub-assembly)
    Spiral cable (Steering Angle Sensor)
    Installed on all vehicles
    Power steering ECU assembly
    Power Steering (EPS)
    Installed on all vehicles
    Air conditioning control assembly
    Air Conditioning Amplifier
    for Automatic Air Conditioning System
    Air bag ECU assembly
    Airbag
    Installed on all vehicles
    PSP (option connector)
    -
    Installed on all vehicles


CAN BUS CHECK

HINT:
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the GTS.

  1. Using the GTS, select "CAN Bus Check" from "System Select".

    NOTICE:
    1. It may be possible to select buses that do not have ECUs or sensors from the bus selection pull-down menu. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)
    2. In the bus selection pull down menu, all buses applicable to the model are displayed (e.g. LIN communication buses are also displayed). Therefore, refer to the wiring diagrams to check the names of the sub buses for CAN communication (Click here).

    HINT:
    Different connection statuses are indicated by the background color of the ECUs and sensors that are displayed.

    Explanation of CAN Bus Check (Communication Bus Check) screen 
    Bus Type
    Background Color
    Connection Status
    V Bus
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
    Not displayed
    Communication stop has continued since the start of the CAN bus check.*1
    Sub bus
    (gateway function equipped ECU that does not have history of connected ECUs)*2
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
    Not displayed
    Communication stop has continued since the start of the CAN bus check.*1
    Sub bus
    (gateway function equipped ECU that has history of connected ECUs)*3
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Currently not communicating (either of the following):
    1. Communication stop has continued since the start of the CAN bus check
    2. Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring
    Not displayed
    Either of the following:
    1. If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed.
    2. If no ECUs are connected to the sub bus, ''There is no system found on the Communication Bus'' will be displayed.

    HINT:
    1. Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    2. *1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check.
    3. *2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.
    4. *3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.
    5. If none of the connected ECUs are displayed, or there is no response from the vehicle to the GTS, check the DLC3 branch and the V bus main bus lines for a malfunction.

  2. Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.

    HINT:
    1. If an open occurs in one of the lines of a CAN branch (except DLC3), output from the other branch line (the line that is not open) will be unstable and it may interfere the response (display) of other ECUs and sensors.
    2. If the connection status changes during the inspection, repair the open in the branch line of the ECU or sensor that does not respond (is not detected) and then perform the CAN bus check again.


HOW TO INTERPRET CAN BUS CHECK (COMMUNICATION BUS CHECK) SCREEN
  1. When a communication stop is currently occurring, the probable malfunctioning part can be determined from the CAN bus check and by using the following methods.

    NOTICE:
    The following CAN bus wiring diagram is provided only as an example. This wiring diagram is different from the actual wiring diagram for this vehicle.

    HINT:
    1. When a communication stop is currently occurring, it is easier to determine the probable malfunctioning part from the CAN bus check rather than from communication DTCs.
    2. Wait for approximately 2 minutes after turning the ignition switch ON (or simulate the driving conditions that enable the malfunction to be reproduced) and select the CAN bus check. Then observe the communication status of each ECU on the screen.



  2. If a communication error of only 1 ECU or sensor is indicated on the CAN Bus Check screen, a communication stop of the ECU or sensor is suspected.
    Example: Open in both CAN branch lines of ECU B on the V bus


    C240692E01


    Text in Illustration 
    *a
    V Bus
    *b
    Sub bus
    *c
    Terminating Resistor
    *d
    Location of malfunction
    *e
    Not displayed or background color changes to red or yellow
    *f
    CAN Bus Check screen

    HINT:
    When there are communication stops, ECUs are present in the vehicle even though they are not displayed on the CAN Bus Check screen.



  3. C240693E01
  4. If communication errors for multiple ECUs or sensors are indicated on the CAN Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or a sensor which is not displayed) is suspected.
    Example: Open in a CAN branch line for ECU D on the V bus
    Text in Illustration 
    *a
    Background color periodically changes to yellow or red
    *b
    Not displayed or background color is yellow or red
    *c
    Not displayed
    Explanation of CAN Bus Check (Communication Bus Check) screen 
    Bus Type
    Background Color
    Connection Status
    V Bus
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
    Not displayed
    Communication stop has continued since the start of the CAN bus check.*1
    Sub bus
    (gateway function equipped ECU that does not have history of connected ECUs)*2
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
    Not displayed
    Communication stop has continued since the start of the CAN bus check.*1
    Sub bus
    (gateway function equipped ECU that has history of connected ECUs)*3
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Currently not communicating (either of the following):
    1. Communication stop has continued since the start of the CAN bus check
    2. Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring
    Not displayed
    Either of the following:
    1. If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed.
    2. If no ECUs are connected to the sub bus, ''There is no system found on the Communication Bus'' will be displayed.

    HINT:
    1. Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    2. *1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.
    3. *2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.
    4. *3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.
    5. The example of the CAN Bus Check screen in the illustration shows the result of electrical noise on the CAN bus which is caused by an open in a CAN branch line of ECU D (output from the other branch line is unstable) and the communication of ECU C is also unstable. In addition, in this example, ECU C is equipped with a gateway function. Therefore, communication is also unstable between the sub bus ECUs of ECU C and the V bus.
    6. The example in the illustration shows that ECU D is not displayed on the CAN Bus Check screen. This indicates a more significant communication stop. In this case, a communication stop of ECU D is suspected.



  5. C240694E01
  6. If a communication error is indicated on both the V bus and sub bus on the CAN Bus Check screen, suspect any communication stop displayed for the V bus first.
    Example: Open in both CAN branch lines of ECU C on the V bus
    Text in Illustration 
    *a
    Not displayed or background color changes to red

    HINT:
    1. In the CAN bus check, it is possible to confirm the communication status of ECUs connected to the V bus after connecting the GTS to the DLC3. As for the sub buses, it is possible to confirm which sub bus connected ECUs can communicate with a gateway function equipped ECU on the V bus.
    2. If a gateway function equipped ECU has a communication error, ECUs connected to the gateway function equipped ECU are also affected, and communication stops will be indicated.
    3. The CAN Bus Check screen in the illustration shows that ECU C has a gateway function and a communication stop in ECU C is suspected.



  7. C240695E01
  8. If the CAN Bus Check screen indicates a communication stop only in the sub bus, a communication stop in the sub bus is suspected.
    Example: Open in both CAN branch lines of ECU G on the sub bus
    Text in Illustration 
    *a
    Background color changes to red

    HINT:
    1. A communication error in a sub bus does not affect the V bus or other buses.
    2. When a gateway function equipped ECU has memorized the ECUs that are connected to the sub bus, if any of the ECUs connected to the gateway function equipped ECU has a communication error, the background color changes to yellow or red. (The displayed name will not disappear.)



  9. If both of the V bus main bus lines are open, ECUs or sensors that are located farther away from the DLC3 than the open part will be displayed as a communication stop on the CAN Bus Check screen.
    (In this case, ECU A and B are not displayed or their background color changes to red.)


    C240696E01


    Text in Illustration 
    *a
    V Bus
    *b
    Sub Bus
    *c
    Terminating Resistor
    *d
    Location of malfunction
    *e
    Not displayed or background color is red
    *f
    CAN Bus Check screen

    HINT:
    If a communication error occurs in an ECU, it is not displayed on the CAN Bus Check screen even though the ECU is present.



  10. If both of the sub bus main bus lines are open, the ECUs that are located farther away from the gateway function equipped ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.
    (In this case, ECU I and J are not displayed or their background color changes to red.)


    C240697E01


    Text in Illustration 
    *a
    V Bus
    *b
    Sub Bus
    *c
    Terminating Resistor
    *d
    Location of malfunction
    *e
    Not displayed or background color is red
    *f
    CAN Bus Check screen
    *g
    Gateway function equipped ECU
    -
    -



  11. C240698E01
  12. When any of the following malfunctions occurs, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the CAN Bus Check screen.
    Text in Illustration 
    *a
    When any of the following malfunctions occurs on the V bus
    *b
    When any of the following malfunctions occurs on a sub bus
    *c
    Not displayed
    Details of Malfunction 
    Short between CAN lines (CANH and CANL)
    Short between a CAN line (CANH or CANL) and +B
    Short between a CAN line (CANH or CANL) and ground
    Open in a CAN main bus line

    HINT:
    1. When a malfunction occurs on the V bus, almost all ECUs and sensors on the V bus and sub bus indicate a communication error (almost all ECUs are not displayed). As communication with the gateway function equipped ECU that is connected to the V bus stops, communication from the ECUs connected to the sub bus that is monitored by the gateway function equipped ECU also stops (these ECUs are not displayed).
    2. When a malfunction occurs in a sub bus, almost all ECUs connected to the sub bus indicate a communication error.
    3. A communication error in a sub bus does not affect the V bus or other buses.
    4. The malfunctioning part can be determined by checking for a short circuit between CAN bus lines or between a CAN bus line and ground or +B short using an electrical tester.


HOW TO INTERPRET COMMUNICATION DTCS (DTCS THAT START WITH U)


  1. If a CAN communication error cannot be reproduced, determine the suspected malfunctioning part using the DTCs stored in ECUs that are connected to the CAN buses by following the procedure below.

    HINT:
    Communication DTCs (DTCs that start with U) indicate a communication error between the ECU that stores the DTC and the ECU that is indicated by the DTC.




    1. If multiple ECUs store a communication DTC for a particular ECU, a communication stop of the ECU is suspected.


      C240699E01


      Text in Illustration 
      *a
      Items to be checked
      -
      -

      NOTICE:
      1. This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.
      2. Even though a DTC title may indicate a communication error with a specific ECU, the ECU name used in the DTC name on the GTS may differ depending on the ECU that stores the DTC. (Regarding output DTCs, refer to step 6 and the DTC chart for each ECU.)

      HINT:
      As multiple ECUs indicate a communication stop with the main body ECU, the possibility of a communication stop of the main body ECU is high.



    2. If almost all of the communication DTCs of an ECU are stored, a communication stop of the ECU is suspected.


      C240700E01


      Text in Illustration 
      *a
      Items to be checked
      -
      -

      NOTICE:
      This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.

      HINT:
      If almost all of the DTCs of the main body ECU are stored, the possibility of a communication stop of the main body ECU is high.

    3. When a CAN communication error occurs, many DTCs are output. DTCs other than communication error DTCs (such as DTCs that start with C or B) and communication DTCs for the ABS system are important DTCs, however it may be easier to determine the malfunctioning part by examining the overall situation without considering these DTCs.



  2. To help determine the part of the sub bus that has a communication error, prioritize the communication stop DTCs stored in the gateway function equipped ECU.


    C240701E01


    Text in Illustration 
    *a
    Items to be checked
    *b
    ECM
    *c
    Gateway function equipped ECU
    *d
    Location of malfunction
    *e
    V Bus
    *f
    Sub Bus

    NOTICE:
    This DTC table is from another model, and is only used here to show the ECUs connected to both a V bus and a sub bus. It shows DTCs output when there is an open in the main bus lines for the ECM on the sub bus. This table does not show DTCs applicable to this vehicle.

    HINT:
    1. As gateway function equipped ECUs (sub bus monitor ECU) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.
    2. When there is a communication stop for the gateway function equipped ECU (gateway), communication with ECUs connected to other buses such as the V bus stops. Therefore, communication DTCs for ECUs connected to other buses are also stored.

  3. When any of the following malfunctions occurs, many DTCs are likely to be output from many ECUs. Because of this, it may be difficult to determine the probable malfunctioning part.

    1. Short between CAN lines (CANH and CANL)
    2. Short between a CAN line (CANH or CANL) and ground
    3. Short between a CAN line (CANH or CANL) and +B
    4. Open in a CAN branch line (CANH or CANL) of an ECU or sensor
    5. Open in a CAN main bus line (CANH or CANL) between 2 ECUs that have a terminating resistor


DTC TABLE BY ECU

HINT:
  1. In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.
  2. If CAN communication system DTCs are output, trouble cannot be determined only by the DTCs. Perform troubleshooting according to How to Proceed with Troubleshooting (Click here).
  3. If system function temporarily returns to normal, DTCs may not be output again even though the following DTC check procedures are used.

  1. Main Body ECU (Network Gateway ECU) / GTS Display "Main Body"

    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0073
    Control Module Communication Bus "A" Off
    Main body ECU (network gateway computer) communications stopped because of an error with high-speed CAN.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the main body ECU (network gateway ECU) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 15 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0100
    Lost Communication With ECM/PCM "A"
    The main body ECU (network gateway ECU) does not receive data from the ECM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the main body ECU (network gateway ECU) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 15 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0101
    Lost Communication with TCM
    The main body ECU (network gateway ECU) does not receive data from the TCM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the main body ECU (network gateway ECU) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 15 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0122
    Lost Communication with Vehicle Dynamics Control Module
    The main body ECU (network gateway ECU) does not receive data from the skid control ECU (brake actuator assembly).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the main body ECU (network gateway ECU) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 15 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0155
    Lost Communication with Instrument Panel Cluster (IPC) Control Module
    The main body ECU (network gateway ECU) does not receive data from the combination meter assembly.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the main body ECU (network gateway ECU) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 15 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0164
    Lost Communication with HVAC Control Module
    The main body ECU (network gateway ECU) does not receive data from the air conditioning control assembly.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the main body ECU (network gateway ECU) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 15 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0327
    Software Incompatibility with Vehicle Security Control Module
    The main body ECU (network gateway ECU) does not receive data from the certification ECU (smart key ECU assembly).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the main body ECU (network gateway ECU) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 15 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0401
    Invalid Data Received From ECM/PCM "A"
    The main body ECU (network gateway computer) detects abnormal data from the ECM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the main body ECU (network gateway ECU) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 15 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0402
    Invalid Data Received From TCM
    The main body ECU (network gateway computer) detects abnormal data from the TCM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the main body ECU (network gateway ECU) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 15 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0416
    Invalid Data Received From Vehicle Dynamics Control Module
    The main body ECU (network gateway computer) detects abnormal data from the skid control ECU (brake actuator assembly).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the main body ECU (network gateway ECU) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 15 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0423
    Invalid Data Received From Instrument Panel Cluster Control Module
    The main body ECU (network gateway computer) detects abnormal data from the combination meter assembly.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the main body ECU (network gateway ECU) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 15 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0424
    Invalid Data Received From HVAC Control Module
    The main body ECU (network gateway computer) detects abnormal data from the air conditioning control assembly.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the main body ECU (network gateway ECU) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 15 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U1201
    CAN Fail/Error Counter Circuit
    Unstable communications because of an error with high-speed CAN.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the main body ECU (network gateway ECU) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 15 seconds.
    -
    DTC is stored until it is cleared using the GTS.

    HINT:
    This ECU uses the CAN communication system for DTC communication.

  2. Combination Meter Assembly / GTS Display "Combination Meter"

    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0073
    Control Module Communication Bus "A" Off
    The combination meter assembly communications stopped because of an error with high-speed CAN.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the combination meter assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0100
    Lost Communication with ECM/PCM "A"
    The combination meter assembly does not receive data from the ECM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the combination meter assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0122
    Lost Communication with Vehicle Dynamics Control Module
    The combination meter assembly does not receive data from the skid control ECU (brake actuator assembly).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the combination meter assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0131
    Lost Communication with Power Steering Control Module
    The combination meter assembly does not receive data from the power steering ECU assembly.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the combination meter assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0140
    Lost Communication with Body Control Module
    The combination meter assembly does not receive data from the main body ECU (network gateway ECU).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the combination meter assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0151
    Lost Communication with Restraints Control Module
    The combination meter assembly does not receive data from the air bag ECU assembly.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the combination meter assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.

    HINT:
    This ECU uses the CAN communication system for DTC communication.

  3. Certification ECU (Smart Key ECU Assembly) / GTS Display "Smart Key"

    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0073
    Control Module Communication Bus "A" Off
    The certification ECU (smart key ECU assembly) communications stopped because of an error with high-speed CAN.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0100
    Lost Communication with ECM/PCM "A"
    The certification ECU (smart key ECU assembly) does not receive data from the ECM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0101
    Lost Communication with TCM
    The certification ECU (smart key ECU assembly) does not receive data from the TCM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0122
    Lost Communication with Vehicle Dynamics Control Module
    The certification ECU (smart key ECU assembly) does not receive data from the skid control ECU (brake actuator assembly).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0140
    Lost Communication with Body Control Module
    The certification ECU (smart key ECU assembly) does not receive data from the main body ECU (network gateway ECU).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0155
    Lost Communication With Instrument Panel Cluster (IPC) Control Module
    The certification ECU (smart key ECU assembly) does not receive data from the combination meter assembly.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0401
    Invalid Data Received from ECM/PCM "A"
    The certification ECU (smart key ECU assembly) detects abnormal data from the ECM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0422
    Invalid Data Received from Body Control Module
    The certification ECU (smart key ECU assembly) detects abnormal data from the main body ECU (network gateway computer).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.

    HINT:
    This ECU uses the CAN communication system for DTC communication.

  4. ECM / GTS Display "Engine"

    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0073
    Control Module Communication Bus "A" Off
    The ECM communications stopped because of an error with high-speed CAN.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the ECM is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    MIL warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0101
    Lost Communication with TCM
    The ECM does not receive data from the TCM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the ECM is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    MIL warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0122
    Lost Communication with Vehicle Dynamics Control Module
    The ECM does not receive data from the skid control ECU (brake actuator assembly).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the ECM is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    MIL warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0155
    Lost Communication With Instrument Panel Cluster (IPC) Control Module
    The ECM does not receive data from the combination meter assembly.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the ECM is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    MIL warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0402
    Invalid Data Received from TCM
    The ECM detects abnormal data from the TCM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the ECM is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    MIL warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0416
    Invalid Data Received from Vehicle Dynamics Control Module
    The ECM detects abnormal data from the skid control ECU (brake actuator assembly).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the ECM is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    MIL warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0423
    Invalid Data Received from Instrument Panel Cluster Control Module
    The ECM detects abnormal data from the combination meter assembly.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the ECM is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    MIL warning light illuminates.
    DTC is stored until it is cleared using the GTS.

    HINT:
    This ECU uses the CAN communication system for DTC communication.

  5. TCM / GTS Display "ECT"

    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0073
    Control Module Communication Bus "A" Off
    The TCM communications stopped because of an error with high-speed CAN.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the TCM is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0100
    Lost Communication with ECM/PCM "A"
    The TCM does not receive data from the ECM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the TCM is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0122
    Lost Communication with Vehicle Dynamics Control Module
    The TCM does not receive data from the skid control ECU (brake actuator assembly).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the TCM is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0140
    Lost Communication with Body Control Module
    The TCM does not receive data from the main body ECU (network gateway ECU).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the TCM is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0155
    Lost Communication With Instrument Panel Cluster (IPC) Control Module
    The TCM does not receive data from the combination meter assembly.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the TCM is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0401
    Invalid Data Received from ECM/PCM "A"
    The TCM detects abnormal data from the ECM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the TCM is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0416
    Invalid Data Received from Vehicle Dynamics Control Module
    The TCM detects abnormal data from the skid control ECU (brake actuator assembly).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the TCM is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0422
    Invalid Data Received from Body Control Module
    The TCM detects abnormal data from the main body ECU (network gateway computer).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the TCM is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0423
    Invalid Data Received from Instrument Panel Cluster Control Module
    The TCM detects abnormal data from the combination meter assembly.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the TCM is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.

    HINT:
    This ECU uses the CAN communication system for DTC communication.

  6. Skid Control ECU (Brake Actuator Assembly) / GTS Display "ABS/VSC/TRAC"

    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0073
    Control Module Communication Bus OFF
    The skid control ECU (brake actuator assembly) communications stopped because of an error with high-speed CAN.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the skid control ECU (brake actuator assembly) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 60 seconds.
    ABS warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0100
    Lost Communication With ECM/PCM "A"
    The skid control ECU (brake actuator assembly) does not receive data from the ECM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the skid control ECU (brake actuator assembly) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    ABS warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0101
    Lost Communication with TCM
    The skid control ECU (brake actuator assembly) does not receive data from the TCM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the skid control ECU (brake actuator assembly) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    ABS warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0126
    Lost Communication With Steering Angle Sensor Module
    The skid control ECU (brake actuator assembly) does not receive data from the steering angle sensor (spiral cable sub-assembly).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the skid control ECU (brake actuator assembly) is 10 V or more.
    Turn the ignition switch to ON and wait for at least 60 seconds.
    ABS warning light illuminates.
    DTC is stored until it is cleared using the GTS.

    HINT:
    This ECU uses the CAN communication system for DTC communication.

  7. Steering Angle Sensor (Spiral Cable Sub-assembly) / GTS Display "-"

    HINT:
    The steering angle sensor is connected to the CAN communication system, but CAN communication DTCs are not output.

  8. Power Steering ECU Assembly / GTS Display "EMPS"

    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0100
    Lost Communication with ECM/PCM "A"
    The power steering ECU assembly does not receive data from the ECM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the power steering ECU assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    EPS warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0122
    Lost Communication with Vehicle Dynamics Control Module
    The power steering ECU assembly does not receive data from the skid control ECU (brake actuator assembly).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the power steering ECU assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    EPS warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0416
    Invalid Data Received from Vehicle Dynamics Control Module
    The power steering ECU assembly does not send data to the skid control ECU (brake actuator assembly).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the power steering ECU assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    EPS warning light illuminates.
    DTC is stored until it is cleared using the GTS.

    HINT:
    This ECU uses the CAN communication system for DTC communication.

  9. Air Conditioning Control Assembly / GTS Display "Air Conditioner"

    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0073
    Control Module Communication Bus "A" Off
    The air conditioning control assembly communications stopped because of an error with high-speed CAN.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the air conditioning control assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0100
    Lost Communication With ECM/PCM "A"
    The air conditioning control assembly does not receive data from the ECM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the air conditioning control assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0101
    Lost Communication With TCM
    The air conditioning control assembly does not receive data from the TCM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the air conditioning control assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds
    -
    DTC is stored until it is cleared using the GTS.
    U0122
    Lost Communication with Vehicle Dynamics Control Module
    The air conditioning control assembly does not receive data from the skid control ECU (brake actuator assembly).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the air conditioning control assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0140
    Lost Communication with Body Control Module
    The air conditioning control assembly does not receive data from the main body ECU (network gateway ECU).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the air conditioning control assemblyis 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0155
    Lost Communication With Instrument Panel Cluster (IPC) Control Module
    The air conditioning control assembly does not receive data from the combination meter assembly.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the air conditioning control assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0401
    Invalid Data Received from ECM/PCM "A"
    The air conditioning control assembly detects abnormal data from the ECM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the air conditioning control assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0402
    Invalid Data Received from TCM
    The air conditioning control assembly detects abnormal data from the TCM.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the air conditioning control assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0416
    Invalid Data Received from Vehicle Dynamics Control Module
    The air conditioning control assembly detects abnormal data from the skid control ECU (brake actuator assembly).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the air conditioning control assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0422
    Invalid Data Received from Body Control Module
    The air conditioning control assembly detects abnormal data from the main body ECU (network gateway computer).
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the air conditioning control assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0423
    Invalid Data Received from Instrument Panel Cluster Control Module
    The air conditioning control assembly detects abnormal data from the combination meter assembly.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the air conditioning control assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.

    HINT:
    This ECU uses the CAN communication system for DTC communication.

  10. Air Bag ECU Assembly / GTS Display "SRS Airbag"

    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0073
    Control Module Communication Bus "A" Off
    Air bag ECU assembly communications stopped because of an error with high-speed CAN.
    Both conditions are met:
    1. The ignition switch is turned to ON and 1 second elapses.
    2. The power source voltage of the air bag ECU assembly is 10 V or more.
    Turn the ignition switch to ON and wait for at least 60 seconds.
    -
    DTC is stored until it is cleared using the GTS.

    HINT:
    This ECU uses the CAN communication system for DTC communication.

  11. PSP (Option Connector) / GTS Display "-"

    HINT:
    The PSP (option connector) is connected to the CAN communication system, but CAN communication DTCs are not output.


DTC COMBINATION TABLE (OPEN IN CAN BRANCH OF V BUS, PAST COMMUNICATION ERROR)
  1. Regarding the past communication error of ECUs and sensors connected to the V bus (in this case, normal was displayed when performing the CAN bus check, but communication DTCs are output), the probable CAN branch that had a malfunction can be determined based on the following DTC combination table.

    HINT:
    1. Based on the table below and DTCs output from ECUs connected via CAN communication, the probable part for which communication stop occurred can be determined.
    2. Regarding an open in a CAN branch and a communication stop that is currently occurring, the malfunctioning part can be confirmed easily by performing the CAN bus check using the GTS because the ECU or sensor connected to the CAN branch does not respond (the ECU or sensor name will not be displayed on the screen).
    3. If an open in a CAN main bus line, a short between the CAN bus lines (CANH and CANL) or a +B or ground short in the CAN bus occurs, DTCs of almost all ECUs (or sensors) on the CAN bus may be output, or a message indicating a communication error may be displayed on the GTS screen. In this case, check the resistance of the CAN bus (steps 7 to 9) first.
    4. If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.


    DTC
    Trouble Mode
    Output ECU
    Output DTC
    Skid Control ECU Communication Stop Mode (Click here)
    Air Conditioning Amplifier Communication Stop Mode (Click here)
    Power Steering ECU Communication Stop Mode (Click here)
    Steering Angle Sensor Communication Stop Mode (Click here)
    ECM Communication Stop Mode (Click here)
    Transmission Control ECU Communication Stop Mode (Click here)
    Skid Control ECU (Brake Actuator Assembly)
    U0073
    ○*1
    X
    X
    X
    X
    X
    U0100
    ○*1
    X
    X
    X
    ○
    X
    U0101
    ○*1
    X
    X
    X
    X
    ○
    U0126
    ○*1
    X
    X
    ○
    X
    X
    Air Conditioning Control Assembly
    U0073
    X
    ○*1
    X
    X
    X
    X
    U0100
    X
    ○*1
    X
    X
    ○
    X
    U0101
    X
    ○*1
    X
    X
    X
    ○
    U0122
    ○
    ○*1
    X
    X
    X
    X
    U0140
    X
    ○*1
    X
    X
    X
    X
    U0155
    X
    ○*1
    X
    X
    X
    X
    U0401
    X
    X*1
    X
    X
    X
    X
    U0402
    X
    X*1
    X
    X
    X
    X
    U0416
    X
    X*1
    X
    X
    X
    X
    U0422
    X
    X*1
    X
    X
    X
    X
    U0423
    X
    X*1
    X
    X
    X
    X
    Power Steering ECU Assembly
    U0100
    X
    X
    ○*1
    X
    ○
    X
    U0122
    ○
    X
    ○*1
    X
    X
    X
    U0416
    X
    X
    X*1
    X
    X
    X
    ECM
    U0073
    X
    X
    X
    X
    ○*1
    X
    U0101
    X
    X
    X
    X
    ○*1
    ○
    U0122
    ○
    X
    X
    X
    ○*1
    X
    U0155
    X
    X
    X
    X
    ○*1
    X
    U0402
    X
    X
    X
    X
    ○*1
    ○
    U0416
    ○
    X
    X
    X
    ○*1
    X
    U0423
    X
    X
    X
    X
    X*1
    X
    TCM
    U0073
    X
    X
    X
    X
    X
    ○*1
    U0100
    X
    X
    X
    X
    ○
    ○*1
    U0122
    ○
    X
    X
    X
    X
    ○*1
    U0140
    X
    X
    X
    X
    X
    ○*1
    U0155
    X
    X
    X
    X
    X
    ○*1
    U0416
    X
    X
    X
    X
    X
    X*1
    U0422
    X
    X
    X
    X
    X
    X*1
    U0423
    X
    X
    X
    X
    X
    X*1
    Main Body ECU (Network Gateway ECU)
    U0073
    X
    X
    X
    X
    X
    X
    U0100
    X
    X
    X
    X
    ○
    X
    U0101
    X
    X
    X
    X
    X
    ○
    U0122
    ○
    X
    X
    X
    X
    X
    U0155
    X
    X
    X
    X
    X
    X
    U0164
    X
    ○
    X
    X
    X
    X
    U0327
    X
    X
    X
    X
    X
    X
    U0401
    X
    X
    X
    X
    X*2
    X
    U0402
    X
    X
    X
    X
    X
    X*2
    U0416
    X*2
    X
    X
    X
    X
    X
    U0423
    X
    X
    X
    X
    X
    X
    U0424
    X
    X*2
    X
    X
    X
    X
    U1201
    X
    X
    X
    X
    X
    X
    Combination Meter Assembly
    U0073
    X
    X
    X
    X
    X
    X
    U0100
    X
    X
    X
    X
    ○
    X
    U0122
    ○
    X
    X
    X
    X
    X
    U0131
    X
    X
    ○
    X
    X
    X
    U0140
    X
    X
    X
    X
    X
    X
    U0151
    X
    X
    X
    X
    X
    X
    Certification ECU (Smart Key ECU Assembly)
    U0073
    X
    X
    X
    X
    X
    X
    U0100
    X
    X
    X
    X
    ○
    X
    U0101
    X
    X
    X
    X
    X
    ○
    U0122
    ○
    X
    X
    X
    X
    X
    U0140
    X
    X
    X
    X
    X
    X
    U0155
    X
    X
    X
    X
    X
    X
    U0401
    X
    X
    X
    X
    X
    X
    U0422
    X
    X
    X
    X
    X
    X
    Air Bag ECU Assembly
    U0073
    X
    X
    X
    X
    X
    X

    DTC
    Trouble Mode
    Output ECU
    Output DTC
    Main Body ECU Communication Stop Mode (Click here)
    Combination Meter ECU Communication Stop Mode (Click here)
    Certification ECU Communication Stop Mode (Click here)
    Center Airbag Sensor Communication Stop Mode (Click here)
    Bus Buffer ECU Communication Stop Mode (Click here)
    Skid Control ECU (Brake Actuator Assembly)
    U0073
    X
    X
    X
    X
    X
    U0100
    X
    X
    X
    X
    X
    U0101
    X
    X
    X
    X
    X
    U0126
    X
    X
    X
    X
    X
    Air Conditioning Control Assembly
    U0073
    X
    X
    X
    X
    X
    U0100
    X
    X
    X
    X
    X
    U0101
    X
    X
    X
    X
    X
    U0122
    X
    X
    X
    X
    X
    U0140
    ○
    X
    X
    X
    X
    U0155
    X
    ○
    X
    X
    X
    U0401
    X
    X
    X
    X
    X
    U0402
    X
    X
    X
    X
    X
    U0416
    X
    X
    X
    X
    X
    U0422
    X
    X
    X
    X
    X
    U0423
    X
    X
    X
    X
    X
    Power Steering ECU Assembly
    U0100
    X
    X
    X
    X
    X
    U0122
    X
    X
    X
    X
    X
    U0416
    X
    X
    X
    X
    X
    ECM
    U0073
    X
    X
    X
    X
    X
    U0101
    X
    X
    X
    X
    X
    U0122
    X
    X
    X
    X
    X
    U0155
    X
    ○
    X
    X
    X
    U0402
    X
    X
    X
    X
    X
    U0416
    X
    X
    X
    X
    X
    U0423
    X
    X
    X
    X
    X
    TCM
    U0073
    X
    X
    X
    X
    X
    U0100
    X
    X
    X
    X
    X
    U0122
    X
    X
    X
    X
    X
    U0140
    ○
    X
    X
    X
    X
    U0155
    X
    ○
    X
    X
    X
    U0401
    X
    X
    X
    X
    X
    U0416
    X
    X
    X
    X
    X
    U0422
    X
    X
    X
    X
    X
    U0423
    X
    X
    X
    X
    X
    Main Body ECU (Network Gateway ECU)
    U0073
    ○*1
    X
    X
    X
    X
    U0100
    ○*1
    X
    X
    X
    X
    U0101
    ○*1
    X
    X
    X
    X
    U0122
    ○*1
    X
    X
    X
    X
    U0155
    ○*1
    ○
    X
    X
    X
    U0164
    ○*1
    X
    X
    X
    X
    U0327
    ○*1
    X
    ○
    X
    X
    U0401
    X*1
    X
    X
    X
    X
    U0402
    X*1
    X
    X
    X
    X
    U0416
    X*1
    X
    X
    X
    X
    U0423
    X*1
    X*2
    X
    X
    X
    U0424
    X*1
    X
    X
    X
    X
    U1201
    ○*1
    X
    X
    X
    X
    Combination Meter Assembly
    U0073
    X
    ○*1
    X
    X
    X
    U0100
    X
    ○*1
    X
    X
    X
    U0122
    X
    ○*1
    X
    X
    X
    U0131
    X
    ○*1
    X
    X
    X
    U0140
    ○
    ○*1
    X
    X
    X
    U0151
    X
    ○*1
    X
    ○
    X
    Certification ECU (Smart Key ECU Assembly)
    U0073
    X
    X
    ○*1
    X
    X
    U0100
    X
    X
    ○*1
    X
    X
    U0101
    X
    X
    ○*1
    X
    X
    U0122
    X
    X
    ○*1
    X
    X
    U0140
    ○
    X
    ○*1
    X
    X
    U0155
    X
    ○
    ○*1
    X
    X
    U0401
    X
    X
    X*1
    X
    X
    U0422
    X
    X
    X*1
    X
    X
    Air Bag ECU Assembly
    U0073
    X
    X
    X
    ○*1
    X

    HINT:
    1. ○: Set
    2. X: Not set or may be set according to the malfunctioning part when one line of a CAN branch is open.
    3. -: DTC is not output.
    4. *:1 DTC is not output during communication error, but will be output as a history DTC (past DTC) when communication returns to normal.
    5. *:2 DTC may not be stored depending on conditions.


CAN BUS WAVEFORMS

C230845E02

HINT:
  1. This waveform is measured between terminals CANH and GND, and terminals CANL and GND of the DLC3. (Use this as a reference for diagnosis of CAN communication lines.)
  2. When malfunctions in multiple ECUs are suspected based on CAN Bus Check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first (Click here). If no problems are found, check the following waveforms.
  3. If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main bus line, an open in a CAN branch line, or a short between a CAN line (CANH or CANL) and ground is suspected (Group 2).
  4. Wiggle the connector and wire harness to check if the waveform changes.



  1. CAN bus waveforms (Group 1)



      C227926E01
    1. Normal waveform



    2. C239096E01
    3. Open in both of the lines (CANH and CANL) of a CAN branch

      HINT:
      1. Waveforms (waveforms shown using dotted lines) are not present from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)
      2. Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.



    4. C227930E01
    5. Short between the CAN bus lines (CANH and CANL)

      HINT:
      1. Waveforms disappear.
      2. If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.



  2. CAN bus waveforms (reference) (Group 2)

    NOTICE:
    The following CAN bus waveforms can be used only as reference. The actual measured waveform may differ significantly depending on the location of the open or short circuit.




      C227931E01
    1. Open in a CAN branch line (CANH)

      HINT:
      1. An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
      2. Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.



    2. C227932E01
    3. Open in a CAN branch line (CANL)

      HINT:
      1. An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
      2. Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.



    4. C227927E01
    5. Open in a CAN main bus line (CANH)

      HINT:
      1. Waveforms of ECUs or sensors that are nearer to the DLC3 than the open part are almost normal.
      2. Waveforms of ECUs or sensors that are on the opposite side of the DLC3 from the open part are abnormal.
      3. An open in a CAN main bus line can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.



    6. C227928E01
    7. Short between a CAN bus line (CANH) and ground

      HINT:
      1. Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connector or when disconnecting ECUs or sensors.
      2. A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.



    8. C227929E01
    9. Short between a CAN bus line (CANL) and ground

      HINT:
      1. Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connector or when disconnecting ECUs or sensors.
      2. A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.