LIGHTING SYSTEM > ACC Signal Circuit |

| 1.READ VALUE USING GTS |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ACC SW | Ignition switch ACC signal/ON or OFF | ON: Ignition switch ACC OFF: Ignition switch off | - |
|
| ||||
| OK | ||
| ||
| 2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND) |
Disconnect the 3A and 3E instrument panel junction block assembly connectors.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3E-1 - Body ground | Always | 11 to 14 V |
| 3A-20 - Body ground | Ignition switch ACC | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3A-12 - Body ground | Always | Below 1 Ω |
| 3A-13 - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
| OK (w/o Entry and Start System) | A |
| OK (w/ Entry and Start System) | B |
| NG | C |
| *a | Front view of wire harness connector (to instrument panel junction block assembly) |
|
| ||||
|
| ||||
| A | |
| 3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC1 RELAY) |
Remove the instrument panel junction block assembly (Click here).
Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.

| *a | Component without harness connected (Instrument panel junction block assembly) | - | - |
| Tester Connection | Condition | Specified Condition |
| 3E-1 - MB-9 (ACC) | Always | 10 kΩ or higher |
| 3E-1 - MB-9 (ACC) | Battery positive (+) → 3A-20 Battery negative (-) → 3A-12 or 3A-13 | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC1 RELAY) |
Remove the instrument panel junction block assembly (Click here).
Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.

| *a | Component without harness connected (Instrument panel junction block assembly) | - | - |
| Tester Connection | Condition | Specified Condition |
| 3E-1 - MB-9 (ACC) | Always | 10 kΩ or higher |
| 3E-1 - 3B-28 | Always | 10 kΩ or higher |
| 3E-1 - MB-9 (ACC) | Battery positive (+) → 3A-20 Battery negative (-) → 3A-12 or 3A-13 | Below 1 Ω |
| 3E-1 - 3B-28 | Battery positive (+) → 3A-20 Battery negative (-) → 3A-12 or 3A-13 | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3B-28 - D5-22 (ACC) | Always | Below 1 Ω |
| 3B-28 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||