Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Door Courtesy Switch Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (network gateway ECU) detects the condition of the front door courtesy light switch assembly using this circuit.

WIRING DIAGRAM


E249229E01


INSPECTION PROCEDURE

1.READ VALUE USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the display on the GTS.

    OK:
    Normal conditions listed above are displayed.


    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW
    Driver side door courtesy light switch signal/ON or OFF
    ON: Driver side door closed
    OFF: Driver side door open
    -
    P Door Courtesy SW
    Passenger side door courtesy light switch signal/ON or OFF
    ON: Passenger side door closed
    OFF: Passenger side door open
    -

    Result:
    Result
    Proceed to
    OK
    A
    Driver side door courtesy light switch or passenger side door courtesy light switch does not operate
    B



B
Go to step 2
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH)
  1. Remove the front door courtesy light switch assembly (Click here).

  1. Inspect the front door courtesy light switch assembly (Click here).

    OK:
    Front door courtesy light switch assembly is normal.

Result:
Result
Proceed to
OK (for Front LH)
A
OK (for Front RH)
B
NG
C



B
Go to step 5

C
REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (Click here)
A


3.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3B (for RHD) or 3A (for LHD) instrument panel junction block assembly connector.

  1. Disconnect the H21 front door courtesy light switch assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    H21-1 - 3B-13
    Always
    Below 1 Ω
    H21-1 - Body ground
    Always
    10 kΩ or higher

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    H21-1 - 3A-28
    Always
    Below 1 Ω
    H21-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.



  1. Measure the resistance according to the value(s) in the table below. (for RHD)


    E249231E01


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-13 - MB-10 (FPCY)
    Always
    Below 1 Ω



  1. Measure the resistance according to the value(s) in the table below. (for LHD)


    E249230E01


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3A-28 - MB-16 (FDCY)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)  

5.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3A (for RHD) or 3B (for LHD) instrument panel junction block assembly connector.

  1. Disconnect the G18 front door courtesy light switch assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    G18-1 - 3A-28
    Always
    Below 1 Ω
    G18-1 - Body ground
    Always
    10 kΩ or higher

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    G18-1 - 3B-13
    Always
    Below 1 Ω
    G18-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.



  1. Measure the resistance according to the value(s) in the table below. (for RHD)


    E249230E01


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3A-28 - MB-16 (FDCY)
    Always
    Below 1 Ω



  1. Measure the resistance according to the value(s) in the table below. (for LHD)


    E249231E01


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-13 - MB-10 (FPCY)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)