CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to GND (LHD Models) |
| Symptom | Trouble Area |
| No resistance exists between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of DLC3. |
|


| 1.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN NO. 2 J/C) |
![]() |
Disconnect the wire harness connector from the D43 CAN No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| D43-1 - D10-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | CAN No. 1 junction connector |
| D43-12 - D10-4 (CG) | |||
| D43-2 - D10-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Combination meter assembly |
| D43-13 - D10-4 (CG) | |||
| D43-3 - D10-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Main body ECU (network gateway ECU) |
| D43-14 - D10-4 (CG) | |||
| D43-4 - D10-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Certification ECU (smart key ECU assembly) |
| D43-15 - D10-4 (CG) | |||
| D43-5 - D10-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | DLC3 |
| D43-16 - D10-4 (CG) | |||
| D43-6 - D10-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Steering angle sensor (spiral cable sub-assembly) |
| D43-17 - D10-4 (CG) | |||
| D43-7 - D10-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | PSP (option connector) |
| D43-18 - D10-4 (CG) | |||
| D43-8 - D10-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Air bag ECU assembly |
| D43-19 - D10-4 (CG) | |||
| D43-9 - D10-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | ECM |
| D43-20 - D10-4 (CG) | |||
| D43-10 - D10-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Air conditioning control assembly |
| D43-21 - D10-4 (CG) |
| *1 | DLC3 |
| *a | Front view of wire harness connector (to CAN No. 2 Junction Connector) |
| *b | to CAN No. 1 Junction Connector |
| *c | to Combination Meter Assembly |
| *d | to Main Body ECU (Network Gateway ECU) |
| *e | to Certification ECU (Smart Key ECU Assembly) |
| *f | to DLC3 |
| *g | to Steering Angle Sensor (Spiral Cable Sub-assembly) |
| *h | to PSP (Option Connector) |
| *i | to Air Bag ECU Assembly |
| *j | to ECM |
| *k | to Air Conditioning Control Assembly |
| Result | Proceed to |
| OK | A |
| NG (CAN No. 1 junction connector main line) | B |
| NG (ECM main line) | C |
| NG (ECU or sensor branch line) | D |
| NG (DLC3 branch line or PSP (option connector) branch line) | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 2.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN NO. 1 J/C) |
![]() |
Disconnect the wire harness connector from the A17 CAN No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| A17-5 - D10-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | TCM |
| A17-16 - D10-4 (CG) | |||
| A17-6 - D10-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Skid control ECU (brake actuator assembly) |
| A17-17 - D10-4 (CG) | |||
| A17-7 - D10-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | CAN No. 2 junction connector |
| A17-18 - D10-4 (CG) | |||
| A17-8 - D10-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Power steering ECU assembly |
| A17-19 - D10-4 (CG) |
| *1 | DLC3 |
| *a | Front view of wire harness connector (to CAN No. 1 Junction Connector) |
| *b | to TCM |
| *c | to Skid Control ECU (Brake Actuator Assembly) |
| *d | to CAN No. 2 Junction Connector |
| *e | to Power Steering ECU Assembly |
| Result | Proceed to |
| OK | A |
| NG (CAN No. 2 junction connector main line) | B |
| NG (skid control ECU (brake actuator assembly) main line) | C |
| NG (ECU or sensor branch line) | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 3.CHECK FOR SHORT TO GND IN CONNECTED COMPONENT (ECU, SENSOR) |
Reconnect all the wire harness connectors (the A17 CAN No. 1 junction connector and D43 CAN No. 2 junction connector).
Disconnect the ECU or sensor connected to the CAN bus line that is shorted to ground.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D10-6 (CANH) - D10-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| D10-14 (CANL) - D10-4 (CG) |
| *1 | DLC3 |
|
| ||||
| OK | ||
| ||