Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to +B (RHD Models)

for Preparation Click here


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.

Symptom
Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of DLC3.
  1. Short to +B in CAN main bus line
  2. Short to +B in CAN branch line
  3. Main body ECU (network gateway ECU)
  4. Combination meter assembly
  5. Certification ECU (smart key ECU assembly)*1
  6. ECM
  7. TCM*2
  8. Skid control ECU (brake actuator assembly)
  9. Steering angle sensor (spiral cable sub-assembly)
  10. Power steering ECU assembly
  11. Air conditioning control assembly*3
  12. Air bag ECU assembly
  13. CAN No. 1 junction connector
  14. CAN No. 2 junction connector
*1: w/ Entry and Start System
*2: for Automatic Transmission System
*3: for Automatic Air Conditioning System

WIRING DIAGRAM


C261304E01


C261305E01


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the ignition switch to ON, wait at least 60 seconds,
  6. After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 2 J/C)


    C262677E01
  1. Disconnect the wire harness connector from the D43 CAN No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Connected to
    D43-1 - D10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Skid control ECU (brake actuator assembly)
    D43-12 - D10-16 (BAT)
    D43-2 - D10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Combination meter assembly
    D43-13 - D10-16 (BAT)
    D43-3 - D10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Main body ECU (network gateway ECU)
    D43-14 - D10-16 (BAT)
    D43-4 - D10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Certification ECU (smart key ECU assembly)
    D43-15 - D10-16 (BAT)
    D43-5 - D10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    DLC3
    D43-16 - D10-16 (BAT)
    D43-6 - D10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Steering angle sensor (spiral cable sub-assembly)
    D43-17 - D10-16 (BAT)
    D43-7 - D10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    PSP (option connector)
    D43-18 - D10-16 (BAT)
    D43-8 - D10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Air bag ECU assembly
    D43-19 - D10-16 (BAT)
    D43-9 - D10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    CAN No. 1 junction connector
    D43-20 - D10-16 (BAT)
    D43-10 - D10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Air conditioning control assembly
    D43-21 - D10-16 (BAT)

    Text in Illustration 
    *1
    DLC3
    *a
    Front view of wire harness connector
    (to CAN No. 2 Junction Connector)
    *b
    to Skid Control ECU (Brake Actuator Assembly)
    *c
    to Combination Meter Assembly
    *d
    to Main Body ECU (Network Gateway ECU)
    *e
    to Certification ECU (Smart Key ECU Assembly)
    *f
    to DLC3
    *g
    to Steering Angle Sensor (Spiral Cable Sub-assembly)
    *h
    to PSP (Option Connector)
    *i
    to Air Bag ECU Assembly
    *j
    to CAN No. 1 Junction Connector
    *k
    to Air Conditioning Control Assembly

    Result:
    Result
    Proceed to
    OK
    A
    NG (CAN No. 1 junction connector main line)
    B
    NG (Skid control ECU (brake actuator assembly) main line)
    C
    NG (ECU or sensor branch line)
    D
    NG (DLC3 branch line or PSP (option connector) branch line)
    E



B
Go to step 2

C
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 J/C - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))

D
Go to step 3

E
REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3 OR PSP (OPTION CONNECTOR)
A

REPLACE CAN NO. 2 JUNCTION CONNECTOR 

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 1 J/C)


    C262677E02
  1. Disconnect the wire harness connector from the A17 CAN No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Connected to
    A17-5 - D10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    TCM
    A17-16 - D10-16 (BAT)
    A17-6 - D10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    CAN No. 2 junction connector
    A17-17 - D10-16 (BAT)
    A17-7 - D10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    ECM
    A17-18 - D10-16 (BAT)
    A17-8 - D10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Power steering ECU assembly
    A17-19 - D10-16 (BAT)

    Text in Illustration 
    *1
    DLC3
    *a
    Front view of wire harness connector
    (to CAN No. 1 Junction Connector)
    *b
    to TCM
    *c
    to CAN No. 2 Junction Connector
    *d
    to ECM
    *e
    to Power Steering ECU Assembly

Result:
Result
Proceed to
OK
A
NG (CAN No. 2 junction connector main line)
B
NG (ECM main line)
C
NG (ECU or sensor branch line)
D



B
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 J/C - CAN NO. 1 J/C)

C
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 J/C - ECM)

D
Go to step 3
A

REPLACE CAN NO. 1 JUNCTION CONNECTOR 

3.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU, SENSOR)
  1. Reconnect all the wire harness connectors (the A17 CAN No. 1 junction connector and D43 CAN No. 2 junction connector).

  1. Disconnect the ECU or sensor connected to the CAN bus line that is shorted to +B.

    HINT:
    If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to the terminals of ECU tables (Click here).



    E231257E17
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D10-6 - D10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    D10-14 - D10-16 (BAT)

    Text in Illustration 
    *1
    DLC3

HINT:
If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



NG
REPAIR OR REPLACE REPAIR OR REPLACE CORRESPONDING ECU/SENSOR WIRE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR