Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1430/21    Open in Room Temperature Sensor Circuit

DTC    B1431/-21    Short in Room Temperature Sensor Circuit

for Preparation Click here


DESCRIPTION

The cooler (room temp. sensor) thermistor is installed in the instrument panel to detect the cabin temperature which is used to control the heater and air conditioning system AUTO mode. The resistance of the cooler (room temp. sensor) thermistor changes in accordance with the cabin temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.
The air conditioning control assembly applies a voltage (5 V) to the cooler (room temp. sensor) thermistor and reads voltage changes due to changes in the resistance of the cooler (room temp. sensor) thermistor.

DTC No.
DTC Detection Condition
Trouble Area
B1430/21
Open in room temperature sensor circuit
  1. Cooler (room temp. sensor) thermistor
  2. Harness or connector between cooler (room temp. sensor) thermistor and air conditioning control assembly
  3. Air conditioning control assembly
B1431/-21
Short in room temperature sensor circuit
  1. Cooler (room temp. sensor) thermistor
  2. Harness or connector between cooler (room temp. sensor) thermistor and air conditioning control assembly
  3. Air conditioning control assembly

WIRING DIAGRAM


E248910E01


INSPECTION PROCEDURE

1.READ VALUE USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Data List.

  1. Check the value(s) by referring to the table below.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Room Temperature Sensor
    (Room Temp)
    Room Temperature Sensor /
    min.: -72.47°C (-98.4°F)
    max.: 193.82°C (380.9°F)
    Actual cabin temperature displayed
    -

    OK:
    The display is as specified in the normal condition column.

    Result:
    Result
    Proceed to
    OK (When troubleshooting according to the DTC)
    A
    OK (When troubleshooting according to Problem Symptoms Table)
    B
    NG
    C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
Go to step 3
A


2.CHECK FOR DTC
  1. Clear the DTCs .

  1. Check the DTCs .

OK:
DTC is not output.



NG
REPLACE AIR CONDITIONING CONTROL ASSEMBLY
OK

END 

3.INSPECT COOLER (ROOM TEMP. SENSOR) THERMISTOR
  1. Remove the cooler (room temp. sensor) thermistor (Click here).

  1. Inspect the cooler (room temp. sensor) thermistor .



NG
REPLACE COOLER (ROOM TEMP. SENSOR) THERMISTOR (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (COOLER (ROOM TEMP. SENSOR) THERMISTOR - AIR CONDITIONING CONTROL ASSEMBLY)
  1. Disconnect the D20 air conditioning control assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D67-1 - D20-5(TR)
    Always
    Below 1 Ω
    D67-2 - D20-6(SG)
    Always
    Below 1 Ω
    D67-1 - Body ground
    Always
    10 kΩ or higher
    D67-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING CONTROL ASSEMBLY