HEADLIGHT CLEANER ACTUATOR > INSTALLATION |
| 1. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY |
Install the headlight washer actuator sub-assembly with the bolt.
Install the clip.
Connect the headlight washer hose and joint clamp.
| 2. INSTALL FRONT BUMPER COVER |
| 3. ADD WASHER FLUID |
| 4. PREPARE VEHICLE FOR FOG LIGHT AIM ADJUSTMENT (w/ Fog Light) |
Prepare the vehicle:
| 5. PREPARE FOR FOG LIGHT AIMING (w/ Fog Light) |
![]() |
Prepare the vehicle (except China):
| *a | 25 or 3 m (82 or 9.84 ft.) |
| *b | 90° |
![]() |
Prepare the vehicle (for China):
| *a | 10 or 3 m (32.8 or 9.84 ft.) |
| *b | 90° |
Prepare a piece of thick white paper (approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width)) to use as a screen.
Draw a vertical line down the center of the screen (V line).
Set the screen as shown in the illustration (except China).

| *1 | Aligning distance 25 m (82 ft.) | *2 | Aligning distance 3 m (9.84 ft.) |
| *a | V RH Line | *b | V LH Line |
| *c | H Line | *d | V Line |
| *e | 90° | *f | 25 m (82 ft.) |
| *g | 3 m (9.84 ft.) | - | - |
Set the screen as shown in the illustration (for China).

| *1 | Aligning distance 10 m (32.8 ft.) | *2 | Aligning distance 3 m (9.84 ft.) |
| *a | V RH Line | *b | V LH Line |
| *c | H Line | *d | V Line |
| *e | 90° | *f | 10 m (32.8 ft.) |
| *g | 3 m (9.84 ft.) | - | - |
![]() |
Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.
H Line (Fog light height):
Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.
V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):
Draw 2 vertical lines so that they intersect the H line at each center mark (aligned with the center of the fog light bulbs).
| *a | V LH Line |
| *b | V Line |
| *c | V RH Line |
| *d | H Line |
| *e | Ground |
| 6. INSPECT FOG LIGHT AIMING (w/ Fog Light) |
Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.
Start the engine.
Turn on the fog lights and check if the upper edge of the hot zone for each fog light matches the upper edge as shown in the illustration (except China).

| *A | Aligning distance 25 m (82 ft.) | *B | Aligning distance 3 m (9.84 ft.) |
| *a | V RH Line | *b | V LH Line |
| *c | H Line | *d | Hot Zone |
Turn on the fog lights and check if the upper edge of the hot zone for each fog light matches the upper edge as shown in the illustration (for China).

| *A | Aligning distance 10 m (32.8 ft.) | *B | Aligning distance 3 m (9.84 ft.) |
| *a | V RH Line | *b | V LH Line |
| *c | H Line | *d | Hot Zone |
| 7. ADJUST FOG LIGHT AIMING (w/ Fog Light) |
![]() |
Adjust the aim vertically:
Adjust the aim of each fog light to the specified range by turning each aiming screw with a screwdriver.
| *1 | Aiming Screw |