Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM

POWER STEERING SYSTEM > EPS Warning Light Circuit

for Preparation Click here


DESCRIPTION

If the power steering ECU assembly detects a malfunction, the EPS warning light comes on. At this time, the power steering ECU assembly stores a DTC in its memory.

WIRING DIAGRAM


C200250E08


INSPECTION PROCEDURE

NOTICE:
  1. If the power steering ECU assembly is replaced with a new one, perform rotation angle sensor initialization and torque sensor zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When the power supply voltage to the power steering ECU assembly (terminals IG and PIG) drops, required steering effort increases and the EPS warning light turns on.

1.CHECK HARNESS AND CONNECTOR
  1. Turn the ignition switch to ON.

  1. Check the indication condition of the EPS warning light by wiggling the power steering ECU assembly connector and wire harness up and down, and right and left.

    OK:
    EPS warning light indication condition does not change.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)
  1. Check for DTCs (Click here).

    OK:
    DTC is not output.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


3.READ VALUE USING GTS (IG POWER SUPPLY)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / EMPS / Data List.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG Power Supply
    ECU power source voltage/
    Min.: 0.0000 V
    Max.: 20.1531 V
    9 to 16 V
    The ignition switch is ON.

    OK:
    The normal condition value is displayed the GTS.



NG
Go to step 6
OK


4.READ VALUE USING GTS (PIG POWER SUPPLY)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / EMPS / Data List.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    PIG Power Supply
    Power source voltage to active motor/
    Min.: 0.0000 V
    Max.: 20.1531 V
    9 to 16 V
    The engine is running and power steering is operating.

    OK:
    The normal condition value is displayed the GTS.



NG
Go to step 7
OK


5.PERFORM ACTIVE TEST USING GTS (METER / GAUGE SYSTEM)
  1. Perform the Active Test of the combination meter using the GTS (Click here).

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. EPS
    EPS warning light
    OFF/ON
    Vehicle is stopped and engine is idling

  1. Check that the EPS warning light operates in accordance with the Active Test.

    HINT:
    Reconnect the connectors and restore the vehicle to its previous condition before checking the combination meter.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)  

6.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY/BODY GROUND)


    C198250E04
  1. Disconnect the A14 and A15 power steering ECU assembly connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A15-6 (IG) - Body ground
    Ignition switch ON
    9 to 16 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A14-2 (PGND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Power Steering ECU Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)  

7.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY/BODY GROUND)


    C198251E04
  1. Disconnect the A14 power steering ECU assembly connector .

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A14-1 (PIG) - Body ground
    Always
    9 to 16 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A14-2 (PGND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)