Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM

DTC    C1511    Torque Sensor Circuit Malfunction

DTC    C1512    Torque Sensor Circuit Malfunction

DTC    C1513    Torque Sensor Circuit Malfunction

DTC    C1514    Torque Sensor Power Supply Abnormal

DTC    C1517    Torque Hold Abnormal

for Preparation Click here


DESCRIPTION

The torque sensor converts the rotation torque input to the steering wheel into an electrical signal and sends it to the power steering ECU assembly. Based on this signal, the ECU detects steering effort.

DTC Code
DTC Detection Condition
Trouble Area
C1511
A torque sensor (TRQ1) signal error or stop
  1. Steering column assembly (torque sensor)
  2. Power steering ECU assembly
C1512
A torque sensor (TRQ2) signal error or stop
C1513
The deviation between torque sensor TRQ1 and TRQ2 exceeds a specified value.
C1514
A torque sensor power supply voltage error
C1517
Temporary control due to a malfunction related to the torque sensor continues for long time.

WIRING DIAGRAM


C261868E01


INSPECTION PROCEDURE

NOTICE:
If the power steering ECU assembly or steering column assembly is replaced, perform rotation angle sensor initialization and torque sensor zero point calibration (Click here).

1.CHECK CONNECTOR CONNECTION CONDITION (TORQUE SENSOR - POWER STEERING ECU ASSEMBLY)


    C198234E15
  1. Check the connection condition of the z2 torque sensor connector.

    OK:
    Torque sensor connector is securely connected to the power steering ECU assembly.

    Text in Illustration 
    *a
    Component with harness connected
    (Power Steering ECU Assembly)



NG
CONNECT CONNECTOR SECURELY
OK


2.CHECK POWER STEERING ECU ASSEMBLY (TRQV VOLTAGE)
  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON.



    C198234E16
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    z2-9 (TRQV) - z2-11 (TRQG)
    Ignition switch ON
    4.5 to 5.5 V

    HINT:
    When the value is within the specified range, record the value.

    Text in Illustration 
    *a
    Component with harness connected
    (Power Steering ECU Assembly)



NG
REPLACE POWER STEERING ECU ASSEMBLY (Click here)
OK


3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)


    C198234E17
  1. Start the engine.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    z2-8 (TRQ1) - z2-11 (TRQG)
    Engine running, steering wheel not turned (without load)
    2.3 to 2.7 V
    Engine running, steering wheel turned to right with vehicle stopped
    2.3 to 3.8 V
    Engine running, steering wheel turned to left with vehicle stopped
    1.2 to 2.7 V
    z2-10 (TRQ2) - z2-11 (TRQG)
    Engine running, steering wheel not turned (without load)
    2.3 to 2.7 V
    Engine running, steering wheel turned to right with vehicle stopped
    1.2 to 2.7 V
    Engine running, steering wheel turned to left with vehicle stopped
    2.3 to 3.8 V

  1. Calculate the difference between the value recorded when measuring the voltage at terminal TRQV in the previous step, and the sum of the output of torque sensor 1 and torque sensor 2.

    OK:
    0.3 V or less (Absolute value)

    Text in Illustration 
    *a
    Component with harness connected
    (Power Steering ECU Assembly)



NG
REPLACE STEERING COLUMN ASSEMBLY (Click here)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)