Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)

WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System) > No Answer-Back

for Preparation Click here


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light and/or wireless door lock buzzer answer-back function(s)* does not operate. In such cases, hazard warning light and wireless door lock buzzer signal outputs from the main body ECU (network gateway ECU) may be malfunctioning.
  1. *: w/ Wireless Door Lock Buzzer Answer-back Function

WIRING DIAGRAM


B315516E03


INSPECTION PROCEDURE

NOTICE:
The wireless door lock control system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (Click here).

1.READ VALUE USING GTS (ANSWER-BACK OPERATION)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Utility / Customize / Wireless Door Lock.

  1. Select the setting by referring to the table below.

    Display
    Default
    Content
    Setting
    Relevant ECU
    Hazard Answer Back
    ON
    When the doors are locked by wireless operation, the hazard warning lights flash once.
    When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
    OFF or ON
    Main body ECU (network gateway ECU)
    Wireless Buzzer Resp*
    ON
    Wireless door lock buzzer response
    OFF or ON
    Main body ECU (network gateway ECU)
    Wireless Buzzer Vol*
    Level 5
    Wireless door lock buzzer volume
    Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level 0
    Main body ECU (network gateway ECU)

    1. *: w/ Wireless Door Lock Buzzer Answer-back Function

    Result:
    Result
    Proceed to
    Both items are ON and except Level 0
    A
    Either item is OFF or Level 0
    B



B
PERFORM CUSTOMIZE FUNCTION (Click here)
A


2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
  1. Check the wireless door lock control function using the electrical key transmitter sub-assembly (Click here).

    Result:
    Result
    Proceed to
    Wireless door lock/unlock operates normally (w/ Wireless Door Lock Buzzer Answer-back Function).
    A
    Wireless door lock/unlock operates normally (w/o Wireless Door Lock Buzzer Answer-back Function).
    B
    Wireless door lock/unlock does not operate normally.
    C



B
Go to step 9

C
GO TO PROBLEM SYMPTOMS TABLE (Click here)
A


3.CHECK WIRELESS ANSWER-BACK OPERATION
  1. Check the wireless answer-back operation using the electrical key transmitter sub-assembly (Click here).

    Result:
    Result
    Proceed to
    Only wireless door lock buzzer answer-back does not occur.
    A
    Only hazard warning light answer-back does not occur.
    B



B
Go to step 9
A


4.PERFORM ACTIVE TEST USING GTS (WIRELESS DOOR LOCK BUZZER)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. Perform the Active Test according to the display on the GTS.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Wireless Buzzer
    Wireless door lock buzzer
    OFF/ON
    -

    Result:
    Result
    Proceed to
    Wireless door lock buzzer does not turn on/off.
    A
    Wireless door lock buzzer turns on/off.
    B



B
REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)
A


5.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU)
  1. Disconnect the A63 wireless door lock buzzer and A73 main body ECU (network gateway ECU) connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A63-1 (+) - A73-1 (BZR)
    Always
    Below 1 Ω
    A63-2 (-) - Body ground
    Always
    Below 1 Ω
    A63-1 (+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. Remove the instrument panel junction block assembly (Click here).


    B312640E05


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    MB-3 - 3B-14
    Always
    Below 1 Ω
    MB-3 - 3B-16
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


7.REPLACE WIRELESS DOOR LOCK BUZZER
  1. Temporarily replace the wireless door lock buzzer with a new one (Click here).


NEXT


8.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
  1. Check the operation of the wireless answer-back function (Click here).

    OK:
    Wireless answer-back function operates normally.



NG
REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)
OK

END (WIRELESS DOOR LOCK BUZZER WAS DEFECTIVE) 

9.HAZARD WARNING LIGHTS OPERATION
  1. Check that the hazard warning light blinks when the hazard warning signal switch is pressed.

    OK:
    Hazard warning light signal is normal.



NG
GO TO LIGHTING SYSTEM (PROBLEM SYMPTOMS TABLE) (Click here)
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)