Home › Engine / Hybrid System › FA20 COOLING › COOLING FAN MOTOR

COOLING FAN MOTOR > REMOVAL

for Preparation Click here



1. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A276525
  1. Disengage the clamp, and disconnect the mass air flow meter connector.

  1. Remove the 3 bolts.

  1. Loosen the hose clamp, and disconnect the hose.

  1. Remove the air cleaner case sub-assembly.



2. REMOVE FRONT BUMPER COVER
(Click here)


3. REMOVE AIR CLEANER DUCT


    A278312
  1. Remove the 2 bolts and air cleaner duct.



4. REMOVE RADIATOR COVER PLATE


    A278313
  1. Remove the 6 clips and radiator cover plate.



5. REMOVE RADIATOR RESERVE TANK ASSEMBLY


    A277918
  1. Remove the 2 bolts and radiator reserve tank assembly.



6. REMOVE WATER FILLER SUB-ASSEMBLY


    A281443
  1. Remove the 4 bolts and separate the water filler sub-assembly.



7. DISCONNECT HOOD LOCK ASSEMBLY (for LHD)


    B313108
  1. Remove the 3 bolts and hood lock assembly.

  1. Disconnect the hood lock control cable assembly from the hood lock assembly.



8. DISCONNECT HOOD LOCK ASSEMBLY (for RHD)


    B309228
  1. Remove the 3 bolts and hood lock assembly.

  1. Disconnect the hood lock control cable assembly from the hood lock assembly.



9. REMOVE RADIATOR SUPPORT SUB-ASSEMBLY


    A277923
  1. Remove the 2 bolts.



    A277926
  1. Remove the 4 bolts and radiator support sub-assembly.



10. REMOVE FAN SHROUD


    A277942E01
  1. Disconnect the 2 wire harness clamps and the 2 cooling fan motor connectors.
    Text in Illustration 
    *1
    Cooling fan motor connector
    *2
    No. 2 cooling fan motor connector (with Air Conditioning System)

    NOTICE:
    Be careful not to damage the connectors.



    A277927
    A282916E01
  1. Mark the sponge on the upper surface of the fan shroud, and use scissors, etc. to cut the sponge.

    HINT:
    Cut the radiator packing at the position between the corner of the radiator packing and the edge of the fun shroud.

    Text in Illustration 
    *1
    Cutting Line



    A277929
    A277943E01
  1. Detach the 2 claws and separate the fan shroud from the radiator assembly.
    Text in Illustration 
    *1
    Cardboard or Blanket
    *2
    Fan shroud

    HINT:
    Insert a cardboard or a blanket between the radiator assembly and the fan shroud to protect the radiator assembly.



    A277944
  1. Remove the fan shroud from the radiator assembly.

    NOTICE:
    Do not apply any excessive force to the outlet radiator hose, inlet radiator hose, No. 1 radiator hose, pipe or water filler sub-assembly when removing the fan shroud.



11. REMOVE FAN


    A277945
  1. Remove the nut and fan.



12. REMOVE NO. 2 FAN (w/ Air Conditioning System)


    A281321
  1. Remove the nut and No. 2 fan.



13. REMOVE COOLING FAN MOTOR (w/o Air Conditioning System)


    A277947
  1. Remove the 3 screws and cooling fan motor.



14. REMOVE COOLING FAN MOTOR (w/ Air Conditioning System)


    A277946
  1. Disengage the connector clamp, and disconnect the connector from cooling fan motor.



    A277947
  1. Remove the 3 screws and cooling fan motor.



15. REMOVE NO. 2 COOLING FAN MOTOR (w/ Air Conditioning System)


    A277949
  1. Remove the 3 screws and the No. 2 cooling fan motor.