Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM

LIN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (NETWORK GATEWAY ECU)

B311513E02


Text in Illustration 
*1
Instrument Panel Junction Block Assembly
*2
Main Body ECU (Network Gateway ECU)
  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly (Click here).

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No.
    (Symbol)
    Wiring Color
    Terminal Description
    Switch Condition
    Specified Condition
    MB-1 (BECU) - Body ground
    None - Body ground
    Battery power supply
    Always
    11 to 14 V
    MB-8 (IG) - Body ground
    None - Body ground
    Battery power supply
    Ignition switch ON
    11 to 14 V
    MB-11 (GND) - Body ground
    None - Body ground
    Ground
    Always
    Below 1 Ω
    MB-32 (BMPX) - Body ground
    None - Body ground
    Battery power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Install the main body ECU (network gateway ECU) onto the instrument panel junction block assembly.

  4. Measure the pulses according to the value(s) in the table below.

    Terminal No.
    (Symbol)
    Wiring Color
    Terminal Description
    Switch Condition
    Specified Condition
    D5-4 (LIN) - D6-1 (GND)
    LG - B
    LIN Communication line
    Ignition switch ON
    Pulse generation
    If the result is not as specified, the main body ECU (network gateway ECU) or instrument panel junction block assembly may have a malfunction.


CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

E246782E01


Text in Illustration 
*1
for RHD
*2
for LHD
  1. Disconnect the F6*1 or E8*2 power window regulator master switch assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No.
    (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F6-5 (GND) - Body ground*1
    B - Body ground
    Ground
    Always
    Below 1 Ω
    E8-5 (GND) - Body ground*2
    F6-12 (+B) - Body ground*1
    SB - Body ground
    Battery power supply
    Always
    11 to 14 V
    E8-12 (+B) - Body ground*2
    If the result is not as specified, there may be a malfunction in the wire harness.
    *1 : for RHD
    *2 : for LHD


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)

B264892E42

  1. Disconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No.
    (Symbol)
    Wiring Color
    Terminal Description
    Switch Condition
    Specified Condition
    D48-2 (+B) - D48-11 (GND)
    R - B
    Battery power supply
    Always
    11 to 14 V
    D48-11 (GND) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω

  3. Connect the D41 and D48 certification ECU (smart key ECU assembly) connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No.
    (Symbol)
    Wiring Color
    Terminal Description
    Switch Condition
    Specified Condition
    D41-5 (IG2) - D48-11 (GND)
    Y - B
    Battery power supply
    Ignition switch ON
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.


CHECK STEERING LOCK ACTUATOR ASSEMBLY (w/ Entry and Start System)

B201269E05

  1. Disconnect the D59 steering lock actuator assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No.
    (Symbol)
    Wiring Color
    Terminal Description
    Switch Condition
    Specified Condition
    D59-1 (GND) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    D59-6 (IGN1) - D59-1 (GND)
    BR - B
    Battery power supply
    Ignition switch ON
    11 to 14 V
    D59-7 (B) - D59-1 (GND)
    SB - B
    Battery power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.


CHECK ID CODE BOX (IMMOBILISER CODE ECU) (w/ Entry and Start System with ID Code Box)

E249054E01

  1. Disconnect the A30 ID code box (immobiliser code ECU) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No.
    (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A30-1 (+B) - A30-5 (GND)
    R-W - B-Y
    Battery power supply
    Always
    11 to 14 V
    A30-5 (GND) - Body ground
    B-Y - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.