Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM

DTC    B2785    Communication Malfunction between ECUs Connected by LIN

for Preparation Click here


DESCRIPTION

The certification ECU (smart key ECU assembly) monitors the communications with the steering lock actuator assembly connected to the certification LIN bus and the ID code box (immobiliser code ECU)*. DTC B2785 is stored if the certification ECU (smart key ECU assembly) detects a communications error between the steering lock actuator assembly connected to the certification LIN bus and the ID code box (immobiliser code ECU), and the LIN communications error (+B short, GND short, communication not possible because of noise, etc.) continues for 1 second.

DTC No.
DTC Detection Condition
Trouble Area
B2785
The certification ECU (smart key ECU assembly) detects a LIN communication error (+B short, GND short, communication not possible because of noise, etc.) that continues for 1 second.
  1. Certification ECU (smart key ECU assembly)
  2. Steering lock actuator assembly
  3. ID code box (immobiliser code ECU)*
  4. Harness or connector
* : w/ ID Code Box

WIRING DIAGRAM


E201074E14


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the ID code box (immobiliser code ECU)*, certification ECU (smart key ECU assembly) or steering lock actuator assembly (steering lock ECU), refer to the registration procedures for the Service Bulletin.
  2. When using the GTS with the engine switch off to troubleshoot:
    Connect the GTS to the vehicle and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
* : w/ ID Code Box

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC 2785 is output
    A
    DTC 2785 is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - EACH ECU)
  1. Disconnect the D41 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the D59 steering lock actuator assembly connector.

  1. Disconnect the A30 ID code box (immobiliser code ECU)* connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D41-17 (LIN) - D59-5 (LIN)
    Always
    Below 1 Ω
    D41-17 (LIN) - A30-2 (LIN)*
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D41-17 (LIN) or D59-5 (LIN) - Body ground
    Always
    10 kΩ or higher
    D41-17 (LIN) or A30-2 (LIN) - Body ground*
    Always
    10 kΩ or higher

  1. Reconnect the D41 certification ECU (smart key ECU assembly) connector.

  1. Reconnect the D59 steering lock actuator assembly connector.

* : w/ ID Code Box


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.SYSTEM CHECK
  1. Check the vehicle specifications.

Result 
Result
Proceed to
w/ ID Code Box
A
w/o ID Code Box
B


B
Go to step 7
A


5.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


6.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2785 is output
    A
    DTC B2785 is not output
    B



B
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
A


7.CLEAR DTC
  1. Disconnect the D59 steering lock actuator assembly connector.

  1. Clear the DTCs (Click here).


NEXT


8.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2785 is output
    A
    DTC B2785 is not output
    B



B
REPLACE STEERING LOCK ACTUATOR ASSEMBLY (Click here)
A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)