Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM

DTC    B2786    No Response from Steering Lock ECU

for Preparation Click here


DESCRIPTION

This DTC is stored when the communication between the certification ECU (smart key ECU assembly) and the steering lock actuator assembly stops for more than 10 seconds.

DTC No.
DTC Detection Condition
Trouble Area
B2786
This DTC is stored when communication between the certification ECU (smart key ECU assembly) and the steering lock actuator assembly stops for more than 10 seconds.
  1. Steering lock actuator assembly
  2. Certification ECU (smart key ECU assembly)
  3. Wire harness or connector

WIRING DIAGRAM


E219752E03


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the certification ECU (smart key ECU assembly) or steering lock actuator assembly (steering lock ECU), refer to the registration procedures for the Service Bulletin.
  2. When using the GTS to troubleshoot with the engine switch off:
    Connect the GTS to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When communication between the steering lock actuator assembly and certification ECU (smart key ECU assembly) stops, DTC B2785 is also stored.

1.CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTC (Click here).

Result 
Result
Proceed to
DTC B2786 is output
A
DTC B2786 and B2785 is output
B


B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ACTUATOR ASSEMBLY
  1. Disconnect the D41 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the D59 steering lock actuator assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D41-17 (LIN) - D59-5 (LIN)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D41-17 (LIN) or D59-5 (LIN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
E175960E06
  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
D59-1 (GND) - Body ground
Always
Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D59-6 (IGN1) - Body ground
Engine Switch On (IG)
11 to 14 V
D59-7 (B) - Body ground
Always
11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Steering Lock Actuator Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


5.REPLACE STEERING LOCK ACTUATOR ASSEMBLY
  1. Replace the steering lock actuator assembly. (Click here)


NEXT


6.CHECK DTC OUTPUT
  1. Clear the DTC (Click here).

  1. Recheck for DTCs.
    Result 
    Result
    Proceed to
    DTC B2786 is not output
    A
    DTC B2786 is output
    B



B
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
A

END (STEERING LOCK ACTUATOR ASSEMBLY WAS DEFECTIVE)