Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Odo/Trip Switch Malfunction

for Preparation Click here


DESCRIPTION

The ODO/TRIP display of the combination meter changes each time the trip switch is pressed.

HINT:
For more information about switching between displays, refer to the owner's manual.


WIRING DIAGRAM


E249058E02


INSPECTION PROCEDURE

1.READ VALUE USING GTS (MULTI DISPLAY SELECT SWITCH, ODO/TRIP CHANGE SW)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Combination Meter / Data List.

  1. According to the display on the tester, read the Data List.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ODO/TRIP Change SW
    ODO/TRIP switch / OFF or ON
    OFF: ODO/TRIP switch not pushed
    -
    ON: ODO/TRIP switch pushed
    Multi Display Select Switch
    Multi Display Select Switch / OFF or ON
    OFF: DISP switch not pushed
    -
    ON: DISP switch pushed

    OK:
    The value displayed on the GTS changes in accordance with the actual ODO/TRIP change switch and multi display select switch operation.



NG
Go to step 2
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

2.INSPECT TRIP SWITCH


    E249059E01
  1. Remove the trip switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (TRIP) - 1
    ODO/TRIP switch on
    (pushed)
    Below 1 Ω
    2 (TRIP) - 1
    ODO/TRIP switch off
    (not pushed)
    10 kΩ or higher
    3 (DISP) - 1*1
    DISP switch on
    (pushed)
    Below 1 Ω
    3 (DISP) - 1*1
    DISP switch off
    (not pushed)
    10 kΩ or higher
    8 (CS) - 1*2
    km/h/MPH switch on
    (pushed)
    Below 1 Ω
    8 (CS) - 1*2
    km/h/MPH switch off
    (not pushed)
    10 kΩ or higher

*1: except TFT Meter Type
*2 : w/ km/h / MPH Switch
Text in Illustration 
*a
Component without harness connected
(Trip Switch)


NG
REPLACE TRIP SWITCH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - TRIP SWITCH AND BODY GROUND)
  1. Disconnect the D7 combination meter assembly connector.

  1. Disconnect the D64 trip switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D7-34 (DISP) - D64-3 (DISP)*1
    Always
    Below 1 Ω
    D7-35 (CS) - D64-8 (CS)*2
    Always
    Below 1 Ω
    D7-36 (TRIP) - D64-2 (TRIP)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D7-34 (DISP) or D64-3 (DISP) - Body ground*1
    Always
    10 kΩ or higher
    D7-35 (CS) or D64-8 (CS) - Body ground*2
    Always
    10 kΩ or higher
    D7-36 (TRIP) or D64-2 (TRIP) - Body ground
    Always
    10 kΩ or higher

*1: except TFT Meter Type
*2 : w/ km/h / MPH Switch


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)