Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY

FRONT SEAT SIDE AIRBAG ASSEMBLY > REMOVAL

for Preparation Click here


CAUTION:
  1. Be sure to read Precaution thoroughly before servicing. (Click here)
  2. Wear protective gloves. Sharp areas on the parts may may injure your hands.
  3. If the side airbag was deployed, replace the front seat airbag assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage. (Click here)

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. REMOVE FRONT SEAT ASSEMBLY
(Click here)


2. REMOVE RECLINING ADJUSTER RELEASE HANDLE


    B299961E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the claw and remove the reclining adjuster release handle.
    Text in Illustration 
    *1
    Protective Tape



3. REMOVE VERTICAL ADJUSTING HANDLE (for Driver Side)


    B299962
  1. Remove the screw and vertical adjusting handle.



4. REMOVE SEAT ADJUSTER COVER CAP


    B348034E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the 3 claws to remove the seat adjuster cover cap.
    Text in Illustration 
    *1
    Protective Tape



5. REMOVE FRONT SEAT CUSHION SHIELD


    B311900
  1. Remove the 2 screws.

  1. Disengage the 4 claws, 5 guides and clip to remove the front seat cushion shield.



6. REMOVE FRONT SEAT INNER CUSHION SHIELD


    B299964
  1. Disengage the 2 claws and 4 guides to remove the front seat inner cushion shield.



7. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY


    B299970
  1. Disengage the 2 hooks.



    B299965
  1. Disconnect the rubber band of the separate type front seatback cover.



    B281106
  1. Disconnect the front seat heater connector and disengage the clamp. (w/ Seat Heater System)



    B280208
  1. Disengage the fastener and separate the front seat airbag assembly wire harness.



    B311905
  1. Disengage the claw and 4 clamps to separate the front seat airbag assembly wire harness.



    B348038
  1. Remove the washer (for Fold Down Seat Type).



    B311908
  1. Using a T40 "TORX" socket wrench, remove the 4 bolts, separate type front seatback assembly and No. 2 front seat travel link.



8. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
  1. Disconnect the occupant detection sensor connector. (for Front Passenger side)



    B311906
  1. Disengage the claw and 3 clamps to separate the front seat heater wire harness. (w/ Seat Heater System)



  1. Disengage each hook and remove the separate type front seat cushion cover with pad from separate type front seat cushion spring assembly. (for Driver Side)


    B299978



  1. Disengage each hook and remove the separate type front seat cushion cover with pad from separate type front seat cushion spring assembly. (for Front Passenger Side)


    B311409



9. REMOVE FRONT SEAT AIRBAG ASSEMBLY


    B311964
  1. Disengage the 2 clamps.



    B311965
  1. Remove the 2 nuts and the front seat airbag assembly.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.