CAMSHAFT > REMOVAL |
| 1. INSTALL ENGINE STAND |
| 2. REMOVE ENGINE HANGER |
Remove the bolt and engine hanger.
| 3. REMOVE GENERATOR COVER |
![]() |
Remove the 2 bolts and generator cover.
| 4. REMOVE BELT GENERATOR COVER |
![]() |
Disengage the 2 clamps and separate the wire harness from the belt generator cover.
Remove the 2 bolts and belt generator cover.
| 5. REMOVE FAN AND GENERATOR V BELT |
![]() |
While turning the belt tensioner clockwise, align the holes and insert a 3 mm (0.118 in.) hexagon wrench into the holes to hold the belt tensioner.
| *1 | Hexagon Wrench |
Remove the fan and generator V belt from the belt tensioner.
| 6. REMOVE GENERATOR ASSEMBLY |
![]() |
Remove the 2 bolts and generator assembly.
| 7. REMOVE OIL LEVEL DIPSTICK GUIDE |
![]() |
Remove the oil level dipstick sub-assembly.
Remove the bolt and oil level dipstick guide.
Remove the O-ring from the oil level dipstick guide.
| 8. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY |
![]() |
Remove the bolt, washer plate and No. 2 idler pulley sub-assembly.
| 9. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Remove the 4 bolts and V-ribbed belt tensioner assembly.
| 10. REMOVE INJECTOR COVER (for Bank 2) |
![]() |
Remove the 2 bolts and injector cover.
| 11. REMOVE INJECTOR COVER (for Bank 1) |
![]() |
Remove the 2 bolts and injector cover.
| 12. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY |
![]() |
Remove the bolt and disconnect the fuel delivery pipe sub-assembly.
Disconnect the No. 2 fuel vapor feed hose.
![]() |
Remove the union bolt and gasket, and disconnect the fuel delivery pipe sub-assembly.
| 13. SEPARATE VENTILATION HOSE |
![]() |
Disconnect the ventilation hose.
| 14. REMOVE INTAKE MANIFOLD |
![]() |
Disconnect the throttle body assembly connector.
![]() |
Disconnect the 2 water by-pass hoses from the throttle body assembly.
![]() |
Disconnect the vacuum sensor connector.
![]() |
Disconnect the No. 1 vacuum switching valve assembly connector.
![]() |
Disengage the 2 clamps and disconnect the 4 connectors.
| *a | for Bank 2 |
| *b | for Bank 1 |
Disconnect the wire harness.
![]() |
Disconnect the fuel pump connector.
![]() |
Remove the 6 bolts, intake manifold and 2 gaskets.
| *a | for Bank 2 |
| *b | for Bank 1 |
| 15. REMOVE NO. 2 FUEL DELIVERY PIPE |
![]() |
Using a union nut wrench, loosen the 2 union nuts and remove the No. 2 fuel delivery pipe.
| 16. REMOVE FUEL PUMP ASSEMBLY |
![]() |
Using a "TORX" Plus Socket Wrench, remove the 2 bolts and fuel pump assembly.
Remove the O-ring from the fuel pump assembly.
| 17. REMOVE VALVE LIFTER |
![]() |
Remove the valve lifter from the pump drive case assembly.
| 18. REMOVE PUMP DRIVE CASE ASSEMBLY |
![]() |
Using a 6 mm hexagon wrench, remove the 3 bolts and pump drive case assembly.
| 19. REMOVE VACUUM PUMP ASSEMBLY (for Automatic Transmission) |
![]() |
Remove the 3 bolts and vacuum pump assembly.
![]() |
Remove the O-ring.
Remove the seal packing from the vacuum pump assembly and the engine.
| 20. REMOVE REAR CYLINDER HEAD PLATE (for Manual Transmission) |
![]() |
Remove the 3 bolts and rear cylinder head plate.
| 21. REMOVE NO. 1 WATER BY-PASS PIPE (for Automatic Transmission) |
![]() |
Loosen the 2 hose clips and disconnect the 2 water by-pass hoses.
Remove the 2 bolts and No. 1 water by-pass pipe.
| 22. REMOVE NO. 1 WATER BY-PASS PIPE (for Manual Transmission) |
![]() |
Loosen the hose clip and disconnect the water by-pass hose.
Remove the 2 bolts and the No. 1 water by-pass pipe.
| 23. REMOVE CRANKSHAFT PULLEY |
![]() |
Install SST to the crankshaft pulley.
| *1 | Claw |
![]() |
Using SST, hold the crankshaft pulley and loosen the crankshaft pulley set bolt.
| *a | Hold |
| *b | Turn |
Remove the crankshaft pulley.
![]() |
Remove the O-ring and crankshaft pulley spacer.
| 24. REMOVE TIMING CHAIN OR BELT COVER OIL SEAL |
![]() |
Using a screwdriver with its tip wrapped in protective tape, pry out the timing chain or belt cover oil seal.
| *1 | Protective Tape |
| 25. DISCONNECT ENGINE WIRE |
Remove the 2 bolts and disconnect the 2 wire harness clamp brackets from the engine assembly.
![]() |
Remove the bolts and disconnect the wire harness clamp bracket from the engine assembly.
Disconnect the camshaft position sensor connector.
![]() |
Disconnect the camshaft position sensor connector and 2 camshaft timing oil control valve connectors.
![]() |
Disconnect the camshaft position sensor connector and camshaft timing oil control valve connector.
Disconnect the engine oil pressure switch connector and engine oil temperature connector.
Disengage the clamp.
![]() |
Disconnect the camshaft position sensor connector and camshaft timing oil control valve connector.
| 26. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY |
Remove the 32 bolts.

Using a screwdriver with its tip wrapped with protective tape, remove the timing chain or belt cover sub-assembly by prying between the timing chain or belt cover sub-assembly and cylinder head or cylinder block.

| *1 | Protective Tape | - | - |
Remove the 4 O-rings.

| 27. REMOVE CHAIN SUB-ASSEMBLY (for Bank 1) |
![]() |
Temporarily install the crankshaft pulley spacer and crankshaft pulley.
![]() |
Using SST, turn the crankshaft pulley clockwise until the alignment marks on the camshaft timing intake gear assembly RH and the camshaft timing exhaust gear assembly RH, and the crankshaft pulley pin hole are aligned at the positions shown in the illustration.
| *a | Alignment Mark |
| *b | Crankshaft Pulley Pin Hole |
| *c | Crankshaft Timing Gear key |
Remove the crankshaft pulley and crankshaft pulley spacer.
![]() |
Push down the chain tensioner slipper and retain the plunger by inserting a 2.5 mm (0.098 in.) diameter hexagonal wrench into the No. 1 chain tensioner assembly through the stopper plate.
![]() |
Remove the 2 bolts and No. 1 chain tensioner assembly.
Remove the chain tensioner slipper.
![]() |
Using a 5 mm hexagonal wrench, remove the bolt and No. 1 chain vibration damper.
Remove the chain sub- assembly (for bank 1).
| 28. REMOVE CHAIN SUB-ASSEMBLY (for Bank 2) |
Temporarily install the crankshaft pulley spacer and crankshaft pulley.
Using SST, turn the crankshaft pulley clockwise until the alignment marks on the camshaft timing intake gear assembly LH and the camshaft timing exhaust gear assembly LH, and the crankshaft pulley pin hole are aligned at the positions shown in the illustration.

| *a | Alignment Mark | *b | Crankshaft Pulley Pin Hole |
| *c | Crankshaft Timing Gear key | *d | Cylinder Block Guide Pin |
Remove the crankshaft pulley and crankshaft pulley spacer.
![]() |
Push the chain tensioner slipper and retain the plunger by inserting an approximately 1 mm (0.039 in.) diameter wire into the No. 2 chain tensioner assembly through the stopper plate .
![]() |
Remove the 2 bolts and No. 2 chain tensioner assembly.
Remove the chain tensioner slipper.
![]() |
Remove the O-ring from the cylinder block.
![]() |
Using a 5 mm socket hexagon wrench, remove the bolt and No. 1 chain vibration damper.
![]() |
While releasing the tension of chain sub-assembly using SST, remove the chain sub-assembly.
| 29. ROTATE CRANKSHAFT AND CAMSHAFT |
Temporarily install the crankshaft pulley spacer and crankshaft pulley.
![]() |
Using SST, turn the crankshaft about 200 degrees counterclockwise until the crankshaft pulley pin hole is aligned at the position shown in the illustration.
| *a | Crankshaft Pulley Pin Hole |
| *b | Alignment Mark |
| *c | Crankshaft Timing Gear Key |
Remove the crankshaft pulley and crankshaft pulley spacer.
![]() |
Using SST, turn the camshaft timing intake gear assembly LH approximately 180°clockwise, and align the alignment mark on the camshaft timing intake gear assembly LH to the position (zero-lift position) shown in the illustration.
| *a | Alignment Mark |
| 30. REMOVE CAMSHAFT TIMING INTAKE GEAR ASSEMBLY RH |
![]() |
Using SST, hold the camshaft timing intake gear assembly RH and remove the 3 bolts with a "TORX" socket wrench E16.
Remove the camshaft timing intake gear assembly RH.
| 31. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY RH |
![]() |
Using SST, hold the camshaft timing exhaust gear assembly RH and remove the 3 bolts with a "TORX" socket wrench E16.
Remove the camshaft timing exhaust gear assembly RH.
| 32. REMOVE CAMSHAFT TIMING INTAKE GEAR ASSEMBLY LH |
![]() |
Using SST, hold the camshaft timing intake gear assembly LH and remove the 3 bolts with a "TORX" socket wrench E16.
Remove the camshaft timing intake gear assembly LH.
| 33. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY LH |
![]() |
Using SST, hold the camshaft timing exhaust gear assembly LH and remove the 3 bolts with a "TORX" socket wrench E16.
Remove the camshaft timing exhaust gear assembly LH.
| 34. REMOVE IGNITION COIL ASSEMBLY (for Bank 2) |
![]() |
Disconnect the 2 ignition coil connectors from the ignition coil assembly.
Remove the 2 bolts and remove the 2 ignition coils.
| 35. REMOVE SPARK PLUG (for Bank 2) |
![]() |
Remove the 2 spark plugs.
| 36. REMOVE IGNITION COIL ASSEMBLY (for Bank 1) |
![]() |
Disconnect the 2 ignition coil connectors from the ignition coil assembly.
Remove the 2 bolts and remove the 2 ignition coils.
| 37. REMOVE SPARK PLUG (for Bank 1) |
![]() |
Remove the 2 spark plugs.
| 38. REMOVE INJECTOR DRIVER BRACKET |
![]() |
Remove the 2 bolts and injector driver bracket.
| 39. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH |
Operate the engine stand so that the bank 1 side faces upward.
![]() |
Remove the 8 bolts.
Using a screwdriver with its tip wrapped in protective tape, remove the cylinder head cover sub-assembly RH.
Remove the cylinder head cover gasket.
![]() |
Remove the 2 spark plug tube gaskets.
| 40. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH |
![]() |
Loosen the 9 bolts in the order shown in the illustration and remove them.
Using a screwdriver with its tip wrapped in protective tape, remove the camshaft housing sub-assembly RH.
![]() |
Remove the 2 O-rings and 8 No. 1 valve rocker arm sub-assemblies from the cylinder head sub-assembly.
![]() |
Remove the 8 valve adjusting shims and 8 roller rocker arm pivots from the cylinder head sub-assembly.
| 41. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH |
Operate the engine stand so that the bank 2 side faces upward.
![]() |
Remove the 8 bolts.
Using a screwdriver with its tip wrapped in protective tape, remove the cylinder head cover sub-assembly LH.
Remove the cylinder head cover gasket.
![]() |
Remove the 2 spark plug tube gaskets.
| 42. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH |
![]() |
Loosen the 9 bolts in the order shown in the illustration and remove them.
Using a screwdriver with its tip wrapped in protective tape, remove the camshaft housing sub-assembly LH.
![]() |
Remove the 2 O-rings and 8 No. 1 valve rocker arm sub-assemblies from the cylinder head sub-assembly LH.
![]() |
Remove the 8 valve adjusting shims and 8 roller rocker arm pivots from the cylinder head sub-assembly LH.
| 43. REMOVE CAMSHAFT CAP (for Bank 1) |
![]() |
In several steps, uniformly loosen the 12 bolts in the order shown in the illustration, and remove the front camshaft cap RH, intake center camshaft cap RH, intake rear camshaft cap RH, exhaust center camshaft cap RH, and exhaust rear camshaft cap RH.
| 44. REMOVE CAMSHAFT RH (for Bank 1) |
![]() |
Remove the intake camshaft RH and exhaust camshaft RH from the camshaft housing sub-assembly RH.
| 45. REMOVE CAMSHAFT CAP (for Bank 2) |
![]() |
In several steps, uniformly loosen the 13 bolts in the order shown in the illustration, and remove the front camshaft cap LH, intake center camshaft cap LH, intake rear camshaft cap LH, exhaust center camshaft cap LH and exhaust rear camshaft cap LH.
| 46. REMOVE CAMSHAFT LH (for Bank 2) |
![]() |
Remove the intake camshaft LH and exhaust camshaft LH from the camshaft housing sub-assembly LH.