Home › Engine / Hybrid System › FA20 ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here



1. SET HOOD SUB-ASSEMBLY



A276897E01

  1. Change the front hood stay position from A to B, and support the hood sub-assembly at position B.



2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Air Conditioning System)
  1. for HFC-134a (R134a):
    (Click here)

  1. for HFO-1234yf (R1234yf):
    (Click here)



3. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
The power window system utilizes a mechanism in which the door glass moves down slightly when the door is opened, and in which the glass moves up when the door closed in order to prevent the door molding from being damaged. When the negative (-) battery terminal needs to be disconnected for servicing, fully open the driver and passenger door glasses in advance.



5. REMOVE FRONT SUSPENSION UPPER TO COWL BRACE SUB-ASSEMBLY LH


    C260995E02
  1. Remove the bolt, 3 nuts and the front suspension upper to cowl brace sub-assembly LH
    Text in Illustration 
    *a
    Bolt
    *b
    Nut



6. REMOVE FRONT SUSPENSION UPPER TO COWL BRACE SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



7. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE


    A281521
  1. Disconnect the hose.



    A281071
  1. Remove the 2 bolts and disconnect the chamber.



    A283417
  1. Loosen the hose clamp and disconnect the No. 2 ventilation hose.



    A283418
  1. Disconnect the mass air flow meter connector.

  1. Disengage the clamp and separate the wire harness from the air cleaner cap.



    C257564
  1. Loosen the hose clamp.



    A283420
  1. Remove the 3 bolts and air cleaner cap with air cleaner hose.



    A281495
  1. Remove the bolt and stay from the body.



8. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and drain the oil into a container.

  1. Clean and install the oil pan drain plug with a new oil pan drain plug gasket.

    Torque:
    42 N*m{ 425 kgf*cm , 31 ft.*lbf }



9. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator cap, cylinder block drain cock plugs and radiator drain cock plug while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the local regulations.



    A277916
  1. Remove the service hole cover from the front bumper under cover.

  1. Connect a hose with an inside diameter of 8 mm (0.315 in.) to the drain plug.



    A277917
  1. Loosen the radiator drain cock plug.



    A279728
  1. Open the air bleed plug on the heater hose side. (for LHD)



    A279727
  1. Open the air bleed plug on the heater hose side. (for RHD)

  1. Remove the radiator cap and drain the coolant.



10. REMOVE RADIATOR RESERVE TANK ASSEMBLY


    A277918
  1. Remove the 2 bolts and radiator reserve tank assembly.



11. REMOVE WATER FILLER SUB-ASSEMBLY


A276898
  1. Remove the 2 bolts and disconnect the water filler sub-assembly.

  1. Remove the 2 clamps and water filler sub-assembly.



12. REMOVE INJECTOR DRIVER


    A277974E02
  1. Move the lock levers in the direction indicated by the arrow to release the 3 connector locks. Disconnect the 4 connectors from the injector driver.
    Text in Illustration 
    *1
    Lock Lever
    *a
    Release
    V100135
    Lock with Connector
    V100136
    Normal Connector



    A277975
  1. Remove the 3 bolts and injector driver.

    NOTICE:
    Be careful not to drop or strike the injector driver.



13. DISCONNECT ENGINE WIRE (for RHD)

HINT:
Fix the disconnected harness components with tape to keep them out of the way.



  1. for Automatic Transmission:



      A276929E01
    1. Release the lock of connector (A) and disconnect the connector.

    2. Disconnect the connector (B).

    3. Disconnect the 2 wire harness clamps.



    4. A276930
    5. Slide the connector in the direction shown in the illustration, and disconnect the wire harness.



    A276899E01
  1. Remove the bolt and wire harness bracket from the No. 2 engine hanger.

  1. Release the lock of connector (A) and disconnect the connector.

  1. Disconnect the connector (B).



    A276902
  1. Disconnect the wire harness clamp and wire harness from the No. 2 engine hanger.



    A276900
  1. Disconnect the 2 wire harness clamps.

  1. Remove the 2 bolts and 2 wire harness clamp brackets.



    A276901
  1. Disconnect the 5 wire harness clamps.



    A276903
  1. Disconnect the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Disconnect the generator connector and disengage the clamp.



14. DISCONNECT ENGINE WIRE (for LHD)

HINT:
Fix the disconnected harness components with tape to keep them out of the way.



    A276899E01
  1. Remove the bolts and wire harness clamp bracket from the No. 2 engine hanger.

  1. Release the lock of connector (A) and disconnect the connector.

  1. Disconnect the connector (B).



    A282282
  1. Disconnect the connector.



    A276902
  1. Disconnect the wire harness clamp and wire harness from the No. 2 engine hanger.



    A281063
  1. Disconnect the 3 wire harness clamps.



  1. for Automatic Transmission:



      A281064E01
    1. Release the lock of connector (A) and disconnect the connector.

    2. Disconnect the connector (B).



    3. A281065
    4. Slide the connector in the direction shown in the illustration, and disconnect the wire harness.



    5. A281066
    6. Disconnect the 3 wire harness clamps.

    7. Remove the bolt and wire harness clamp bracket.



    A276903
  1. Disconnect the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Disconnect the generator connector and disengage the clamp.



15. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Air Conditioning System)


    A276538E01
  1. Disengage the 3 craws and remove the No. 1 engine cover sub-assembly.

    HINT:
    Disengage the 3 craws in the order shown in the illustration.



16. DISCONNECT VACUUM TUBE CONNECTOR HOSE (for Automatic Transmission)


  1. for LHD:



      A281061
    1. Loosen the hose clamp and disconnect the vacuum tube connector hose.



    2. A281062
    3. Remove the 2 bolts and disconnect the vacuum tube connector hose.



  1. for RHD:



      C260988
    1. Loosen the hose clamp and disconnect the union to check valve hose.



17. DISCONNECT VACUUM TUBE CONNECTOR HOSE (for Manual Transmission)


    C264090E01
  1. Loosen the hose clamp and disconnect the union to check valve hose from the intake manifold.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD



18. REMOVE EXHAUST MANIFOLD
(Click here)


19. FIX FRONT EXHAUST PIPE SUB-ASSEMBLY (for Manual Transmission)


    A277903
  1. Tie the front exhaust pipe sub-assembly to the front cross member sub-assembly with rope.



20. DISCONNECT HEATER WATER HOSE


    A276056
  1. Loosen the 2 hose clamps and disconnect the 2 heater water hoses.



21. DISCONNECT NO. 1 TRANSMISSION OIL COOLER HOSE (for Automatic Transmission)


    A281713
  1. Loosen the clip and disconnect the No. 1 transmission oil cooler hose.



22. REMOVE SUCTION HOSE SUB-ASSEMBLY (w/ Air Conditioning System)


    E246390
  1. Remove the bolt and disconnect the suction hose sub-assembly from the compressor assembly with pulley.

  1. Remove the O-ring from the discharge hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



  1. for LHD:



      A282283
    1. Remove the bolt and slide the hook connector.

    2. Remove the nut and suction pipe sub-assembly.

    3. Remove the O-ring from the suction pipe sub-assembly.

      NOTICE:
      Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



  1. for RHD:



      E246448
    1. Remove the bolt and slide the hook connector.

    2. Disconnect the suction pipe sub-assembly.

    3. Remove the O-ring from the suction pipe sub-assembly.

      NOTICE:
      Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



23. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (w/ Air Conditioning System)


    E246391
  1. Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose from the compressor with magnet clutch.

  1. Remove the O-ring from the No. 1 cooler refrigerant discharge hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



24. REMOVE STARTER ASSEMBLY (for Automatic Transmission)
(Click here)


25. REMOVE STARTER ASSEMBLY (for Manual Transmission)
(Click here)


26. DISCONNECT NO. 3 TRANSMISSION OIL COOLER HOSE (for Automatic Transmission)


    A281712
  1. Loosen the clip and disconnect the No. 3 transmission oil cooler hose.



27. DISCONNECT RADIATOR OUTLET HOSE


    A276058
  1. Loosen the clip and disconnect the radiator outlet hose.



28. DISCONNECT GROUNDED CABLE


    A276059
  1. Remove the 2 bolts and disconnect the 2 grounded cables.



29. REMOVE REAR ENGINE UNDER COVER LH (w/ Floor Under Cover)


    C258518
  1. Remove the 3 bolts and 8 clips, then remove the rear engine under cover LH.



30. REMOVE FRONT STABILIZER BAR (for Automatic Transmission)
(Click here)


31. FIX FRONT EXHAUST PIPE ASSEMBLY (for Automatic Transmission)


    A277903
  1. Tie the front exhaust pipe assembly to the front cross member sub-assembly with rope.



32. SEPARATE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)


    A281519E01
  1. Remove the 3 bolts and 2 nuts.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

    NOTICE:
    In order to prevent dropping, do not remove bolt B.



33. REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)


    A281520E01
  1. Remove the 3 bolts and 2 nuts.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

    NOTICE:
    In order to prevent dropping, do not remove bolt B.



34. SEPARATE FRONT CROSS MEMBER SUB-ASSEMBLY


    A276061
  1. Remove the 2 nuts from the front cross member sub-assembly.



35. REMOVE FLYWHEEL HOUSING UNDER COVER


    C260571
  1. Remove the flywheel housing side cover from the automatic transmission assembly.



36. REMOVE DRIVE PLATE SETTING HEXAGON BOLT (for Automatic Transmission)


    A276036E01
  1. Using SST, hold the crankshaft pulley.

    SST
    09960-10010   (09962-01000, 09963-01000)



    C260572
  1. Remove the 6 drive plate and torque converter setting bolt.



37. SEPARATE FUEL HOSE


  1. for Clamp Type:



      C257571E01
    1. Put matchmarks on the fuel hoses and fuel pipes.
      Text in Illustration 
      *a
      matchmark

    2. Remove the clamp and disconnect the fuel tube, No. 2 fuel tube and fuel tube from the fuel pipe.



  1. for Metal Type:



      C264501
    1. Using SST, disconnect the fuel tube and No. 2 fuel tube from the fuel pipe (Click here).

      SST
      SU003-03936  



    2. A282016
    3. Remove the clamp and disconnect the No. 2 fuel vapor feed hose from the fuel pipe.



38. INSTALL ENGINE HANGER


    A276063E01
  1. Install the engine hanger with the bolt, as shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }

    HINT:
    No. 1 Engine Hanger
    12281-38030
    Bolt
    90119-14120

  1. Use an engine sling device and a mini crane to hold the engine.



39. SUPPORT TRANSMISSION ASSEMBLY


    A276064
  1. Support the transmission assembly clutch housing with a jack.

    NOTICE:
    Support the transmission assembly until the installation of the engine assembly is completed.



40. REMOVE ENGINE ASSEMBLY


    A281496E01
  1. Remove the bolt from the transmission assembly.
    Text in Illustration 
    *A
    for Automatic Transmission
    *B
    for Manual Transmission

  1. Hoist the engine assembly up with an engine sling device and a mini crane.



41. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)


    A276036E01
  1. Using SST, hold the crankshaft.

    SST
    09960-10010   (09962-01000, 09963-01000)



    A276896
  1. Remove the 8 bolts, drive plate and ring gear sub-assembly and rear drive plate spacer.



42. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)


    C258509E01
  1. Put the matchmarks on the clutch cover assembly and the flywheel sub-assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Loosen the 6 bolts one turn at a time until spring tension is released.

  1. Remove the 6 bolts and pull off the clutch cover assembly.

    NOTICE:
    Do not drop the clutch disc assembly.



43. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)
  1. Remove the clutch disc assembly.

    NOTICE:
    Keep the lining part of the clutch disk and the surfaces of the pressure plate and flywheel free of oil and foreign matter.



44. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)


    A276036E01
  1. Using SST, hold the crankshaft.

    SST
    09960-10010   (09962-01000, 09963-01000)



    A276046
  1. Remove the 8 bolts and flywheel sub-assembly.



45. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
  1. Remove the No. 1 crankshaft position sensor plate.



46. INSTALL ENGINE STAND
  1. Set the engine on an engine stand.

    NOTICE:
    With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.



47. REMOVE FRONT ENGINE MOUNTING BRACKET


    A276925
  1. Remove the 4 bolts and 2 front engine mounting brackets.