Home › Vehicle Exterior › BODY PANEL › COWL TOP TO APRON BRACE
BM2090E _01 Vehicle Exterior _060720 BODY PANEL _0297847 COWL TOP TO APRON BRACE F

BODY PANEL  COWL TOP TO APRON BRACE  ASSEMBLY REPLACEMENT  


K105347

REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disk Sander etc.


REMOVAL POINT
1.

*1: Bolts.

2.

After removing the front fender apron patch No.4 and front fender apron patch, remove the cowl top side panel sub-assembly.


U147356E02
2.958,1.333 2.958,0.896 false 2.5,2.979 2.5,4.146 false 4.927,7.427 4.677,8.802 4.677,8.802 4.365,8.802 false 3.042,1.417 3.323,1.708 0.281,0.292 10 false x3 2.896,0.719 3.052,0.865 0.156,0.146 10 false *1 1.552,2.271 1.656,2.427 0.104,0.156 10 false 4 5.052,6.063 5.146,6.219 0.094,0.156 10 false 3 3.188,3.865 3.292,4.021 0.104,0.156 10 false 4 4.208,5.865 4.313,6.021 0.104,0.156 10 false 2 5.76,6.052 5.865,6.208 0.104,0.156 10 false 5 6.688,7.031 6.792,7.188 0.104,0.156 10 false 2 5.854,8.458 5.958,8.615 0.104,0.156 10 false 6 3.552,6.969 3.656,7.125 0.104,0.156 10 false 3 1.125,4.448 3.531,4.76 2.406,0.313 10 false RH:FRONT FENDER APRON PATCH 1.125,4.156 3.854,4.469 2.729,0.313 10 false LH:FRONT FENDER APRON PATCH NO.4 1.615,8.729 4.354,9.042 2.74,0.313 10 false COWL TOP SIDE PANEL SUB-ASSEMBLY

INSTALLATION


Symbol meaning
K108823

Plug Weld
K108825

Plug Weld
K108830

Fillet Weld


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram)

3.

*1: Bolts.

4.

After welding the cowl top side panel sub-assembly to the vehicle side, install the front fender apron patch No.4 and front fender apron patch.

5.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

6.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K139726E01
4.667,5.219 5.833,5.469 1.167,0.25 0.25,9.167 1.521,9.417 1.271,0.25 4.802,9.104 4.802,7.656 false 5.281,6.01 5.281,5.688 false 2.865,4.26 2.865,2.667 false 4.021,3.49 4.646,3.708 0.625,0.219 10 false 15 (0.59) 1.521,4.302 4.292,4.542 2.771,0.24 10 false COWL TOP SIDE PANEL SUB-ASSEMBLY 5.208,5.5 5.521,5.698 0.313,0.198 10 false *1 3.51,9.125 6.208,9.375 2.698,0.25 10 false LH:FRONT FENDER APRON PATCH NO.4 3.49,9.313 5.854,9.521 2.365,0.208 10 false RH:FRONT FENDER APRON PATCH 0.302,9.198 2.656,9.438 2.354,0.24 10 false N*m (kgf*cm, ft.*lbf) : Specified torque 0.313,9.51 0.875,9.75 0.563,0.24 10 false mm (in.) 4.719,5.24 5.906,5.479 1.188,0.24 10 false 7.5 (76, 66 in.*lbf)