2012-2019 86 Service Manual
FA20
Trouble codes (606)
- P000AIntegrated deviations in target intake valve timing and actual intake valve timing per specified time exceed...
- P000BIntegrated deviations in target exhaust valve timing and actual exhaust valve timing per specified time...
- P000CIntegrated deviations in target intake valve timing and actual intake valve timing per specified time exceed...
- P000DIntegrated deviations in target exhaust valve timing and actual exhaust valve timing per specified time...
- P0010Oil control valve current is less than 0.306 A for intake camshaft circuit for 2 seconds or more (bank 1). (1...
- P0011Deviation in target intake valve timing and actual intake valve timing exceeds thresholds (bank 1). (2 trip...
- P0013Oil control valve current is less than 0.306 A for exhaust camshaft circuit for 2 seconds or more (bank 1)....
- P0014Deviation in target exhaust valve timing and actual exhaust valve timing exceeds threshold for 8 seconds...
- P0016Intake camshaft position has slipped from the threshold for 1 second (bank 1). (2 trip detection logic)
- P0017Exhaust camshaft position has slipped from the threshold for 5 seconds (bank 1). (2 trip detection logic)
- P0018Intake camshaft position has slipped from the threshold for 1 second (bank 2). (2 trip detection logic)
- P0019Exhaust camshaft position has slipped from the threshold for 5 seconds (bank 2). (2 trip detection logic)
- P0020Oil control valve current is less than 0.306 A for intake camshaft circuit for 2 seconds or more (bank 2). (1...
- P0021Deviation in target intake valve timing and actual intake valve timing exceeds thresholds (bank 2). (2 trip...
- P0023Oil control valve current is less than 0.306 A for exhaust camshaft circuit for 2 seconds or more (bank 2)....
- P0024Deviation in target exhaust valve timing and actual exhaust valve timing exceeds threshold for 8 seconds...
- P0030Air fuel ratio sensor impedance is greater than 65 Ω for 10 seconds or more. (2 trip detection logic)
- P0031Air fuel ratio sensor heater voltage is less than 1.2 V for 1 second or more. (1 trip detection logic)
- P0032Air fuel ratio sensor heater voltage is 1.2 V or more for 2 seconds or more. (1 trip detection logic)
- P0037Heated oxygen sensor heater voltage is less than battery voltage X 0.3 V for 10 seconds or more. (2 trip...
- P0037Heated oxygen sensor heater voltage is less than battery voltage X 0.3 V for 10 seconds or more. (2 trip...
- P0038Heated oxygen sensor heater voltage is battery voltage X 0.2 V or more for 10 seconds or more. (2 trip...
- P0038Heated oxygen sensor heater voltage is battery voltage X 0.2 V or more for 10 seconds or more. (2 trip...
- P0068One of the following conditions is met (2 trip detection logic): · Manifold absolute pressure sensor voltage...
- P0087Fuel pressure is lower than the target value for 10 seconds or more. (1 trip detection logic)
- P0088Fuel pressure is higher than the target value for 10 seconds or more. (1 trip detection logic)
- P0101One of the following conditions is met (2 trip detection logic): · Mass air flow meter voltage is less than...
- P0102Mass air flow meter voltage is 0.127 V or less for 0.5 seconds or more. (1 trip detection logic)
- P0103Mass air flow meter voltage is 4.723 V or more for 0.5 seconds or more. (1 trip detection logic)
- P0107Manifold absolute pressure sensor voltage is 0.61 V or less for 0.5 seconds or more. (1 trip detection logic)
- P0108Manifold absolute pressure sensor voltage is 3.906 V or more for 0.5 seconds or more. (1 trip detection logic)
- P0111The difference between maximum and minimum values for inlet air temperature sensor voltage is less than 0.02...
- P0112Intake air temperature sensor voltage is less than 0.4 V for 0.5 seconds or more. (1 trip detection logic)
- P0113Intake air temperature sensor voltage is 4.707 V or more for 0.5 seconds or more. (1 trip detection logic)
- P0116The engine coolant temperature has not dropped completely 6 hours after ignition switch turned off. (2 trip...
- P0117Engine coolant temperature sensor voltage is less than 0.47 V for 0.5 seconds or more. (1 trip detection...
- P0117Engine coolant temperature sensor voltage is less than 0.47 V for 0.5 seconds or more. (1 trip detection...
- P0118Engine coolant temperature sensor voltage is more than 4.698 V for 0.5 seconds or more. (1 trip detection...
- P0118Engine coolant temperature sensor voltage is more than 4.698 V for 0.5 seconds or more. (1 trip detection...
- P0122The voltage of VTA1 is 0.213 V or less for 0.024 seconds or more. (1 trip detection logic)
- P0123The voltage of VTA1 is more than 4.772 V for 0.024 seconds or more. (1 trip detection logic)
- P0125Despite estimated engine coolant temperature is 20°C (68 °F) or more, engine coolant temperature sensor value...
- P0125Engine coolant temperature is less than 20°C (68 °F) for 398.5 to 766.4 seconds or more (varies with engine...
- P0128Abnormal (open) thermostat functioning detected. (2 trip detection logic)
- P0131One of the following conditions is met for 1 second or more (1 trip detection logic): · The voltage of A1A+...
- P0132One of the following conditions is met for 1 second or more (1 trip detection logic): · The voltage of A1A+...
- P0133The calculated value for the air fuel ratio sensor response rate deterioration level is less than the...
- P0134Air fuel ratio sensor impedance is 450 Ω or more for 5 seconds or more. (1 trip detection logic)
- P0137Heated Oxygen (HO2) sensor voltage is less than 0.03 V. (2 trip detection logic)
- P0137Heated Oxygen (HO2) sensor voltage is less than 0.03 V. (2 trip detection logic)
- P0138Heated Oxygen (HO2) sensor voltage is 1.2 V or more for 2.5 seconds or more. (2 trip detection logic)
- P0138Heated Oxygen (HO2) sensor voltage is 1.2 V or more for 2.5 seconds or more. (2 trip detection logic)
- P013AThe response rate for heated oxygen sensor voltage to change from 0.5 V (rich) to 0.2 V (lean) is slow for 2...
- P013AThe response rate for heated oxygen sensor voltage to change from 0.5 V (rich) to 0.2 V (lean) is slow for 2...
- P013BThe response rate for heated oxygen sensor voltage to change from 0.3 V (lean) to 0.5 V (rich) is slow for 4...
- P013BThe response rate for heated oxygen sensor voltage to change from 0.3 V (lean) to 0.5 V (rich) is slow for 4...
- P013EHeated oxygen sensor voltage is slow in dropping to 0.5 V or less for 4 seconds or more. (2 trip detection...
- P013EHeated oxygen sensor voltage is slow in dropping to 0.5 V or less for 4 seconds or more. (2 trip detection...
- P013FHeated oxygen sensor voltage is slow in increasing to 0.3V or more for 120 seconds. (2 trip detection logic)
- P013FHeated oxygen sensor voltage is slow in increasing to 0.3V or more for 120 seconds. (2 trip detection logic)
- P0140One of the following conditions is met for 180 seconds or more (2 trip detection logic): · The minimum...
- P0141Heated oxygen sensor heater voltage is less than battery voltage X 0.88 V for 10 seconds or more. (2 trip...
- P0141Heated oxygen sensor heater voltage is less than battery voltage X 0.88 V for 10 seconds or more. (2 trip...
- P014CThe "Rich to Lean response rate deterioration level*" value is standard or less for 70 seconds. (2 trip...
- P014DThe "Lean to Rich response rate deterioration level*" value is standard or more for 70 seconds. (2 trip...
- P015AThe "Rich to Lean delay level*" value is standard or more. (2 trip detection logic)
- P015BThe "Lean to Rich delay level*" value is standard or more. (2 trip detection logic)
- P0171With warm engine and stable air fuel ratio feedback, fuel trim considerably in error to lean side. (2 trip...
- P0172With warm engine and stable air fuel ratio feedback, fuel trim considerably in error to rich side. (2 trip...
- P0191One of the following conditions is met (2 trip detection logic): · Fuel pressure is 1.9 MPa or more 5 hours...
- P0191One of the following conditions is met (2 trip detection logic): · Fuel pressure is 1.9 MPa or more 5 hours...
- P0192Fuel pressure sensor voltage is too low for 2.4 seconds or more. (1 trip detection logic)
- P0192Fuel pressure sensor voltage is too low for 2.5 seconds or more. (1 trip detection logic)
- P0193Fuel pressure sensor voltage is too high for 2.4 seconds or more. (1 trip detection logic)
- P0193Fuel pressure sensor voltage is too high for 2.5 seconds or more. (1 trip detection logic)
- P0196Despite estimated engine oil temperature is higher than 45°C (113°F), engine oil temperature sensor value is...
- P0196Despite estimated engine oil temperature is higher than 45°C (113°F), engine oil temperature sensor value is...
- P0197Engine oil temperature sensor voltage is less than 0.203 V for 0.5 seconds or more. (1 trip detection logic)
- P0197Engine oil temperature sensor voltage is less than 0.203 V for 0.5 seconds or more. (1 trip detection logic)
- P0198Engine oil temperature sensor voltage is more than 4.698 V for 0.5 seconds or more. (1 trip detection logic)
- P0198Engine oil temperature sensor voltage is more than 4.698 V for 0.5 seconds or more. (1 trip detection logic)
- P0201Received diagnostic information (open circuit detected / GND short / +B short or overheating) from the fuel...
- P0202Received diagnostic information (open circuit detected / GND short / +B short or overheating) from the fuel...
- P0203Received diagnostic information (open circuit detected / GND short / +B short or overheating) from the fuel...
- P0204Received diagnostic information (open circuit detected / GND short / +B short or overheating) from the fuel...
- P0222The voltage of VTA2 is 0.213 V or less for 0.024 seconds or more. (1 trip detection logic)
- P0223The voltage of VTA2 is 4.772 V or more for 0.024 seconds or more. (1 trip detection logic)
- P0230Open or short in fuel pump circuit for 2.5 seconds or more. (1 trip detection logic)
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip...
- P0301Misfiring of the No. 1 cylinder occurs and one of the following conditions is met (2 trip detection logic): ·...
- P0302Misfiring of the No. 2 cylinder occurs and one of the following conditions is met (2 trip detection logic): ·...
- P0303Misfiring of the No. 3 cylinder occurs and one of the following conditions is met (2 trip detection logic): ·...
- P0304Misfiring of the No. 4 cylinder occurs and one of the following conditions is met (2 trip detection logic): ·...
- P0327Knock sensor voltage is less than 0.154 V for 1 second or more (bank 1). (1 trip detection logic)
- P0328Knock sensor voltage is more than 4.838 V for 1 second or more (bank 1). (1 trip detection logic)
- P0332Knock sensor voltage is less than 0.154 V for 1 second or more (bank 2). (1 trip detection logic)
- P0333Knock sensor voltage is more than 4.838 V for 1 second or more (bank 2). (1 trip detection logic)
- P0335No crankshaft position sensor signal is sent to the ECM while cranking for 3 seconds or more. (1 trip...
- P0335No crankshaft position sensor signal is sent to the ECM while cranking for 3 seconds or more. (1 trip...
- P0336Crankshaft position sensor signal is not 30 counts per 1 revolution of crankshaft 10 times continuously. (2...
- P0336Crankshaft position sensor signal is not 30 counts per 1 revolution of crankshaft. (2 trip detection logic)
- P0340One of the following conditions is met (1 trip detection logic): · No VVT sensor for intake side signal input...
- P0341VVT sensor for intake side signal is not 3 during crankshaft 2 rotations (bank 1). (1 trip detection logic)
- P0345One of the following conditions is met (1 trip detection logic): · No VVT sensor for intake side signal input...
- P0346VVT sensor for intake side signal is not 3 during crankshaft 2 rotations (bank 2). (1 trip detection logic)
- P0351The ECM driver IC detects open and short in signal line circuit between No. 1 ignition coil and ECM (open...
- P0351The ECM driver IC detects open and short in signal line circuit between No. 1 ignition coil and ECM (open...
- P0352The ECM driver IC detects open and short in signal line circuit between No. 2 ignition coil and ECM (open...
- P0352The ECM driver IC detects open and short in signal line circuit between No. 2 ignition coil and ECM (open...
- P0353The ECM driver IC detects open and short in signal line circuit between No. 3 ignition coil and ECM (open...
- P0353The ECM driver IC detects open and short in signal line circuit between No. 3 ignition coil and ECM (open...
- P0354The ECM driver IC detects open and short in signal line circuit between No. 4 ignition coil and ECM (open...
- P0354The ECM driver IC detects open and short in signal line circuit between No. 4 ignition coil and ECM (open...
- P0365No VVT sensor for exhaust side signal input during crankshaft 7.5 rotations (bank 1). (1 trip detection logic)
- P03662 VVT sensor for exhaust side signals are not output during crankshaft 2 rotations (bank 1). (1 trip...
- P0390No VVT sensor for exhaust side signal input during crankshaft 7.5 rotations (bank 2). (1 trip detection logic)
- P03912 VVT sensor for exhaust side signals are not output during crankshaft 2 rotations (bank 2). (1 trip...
- P0420Diagnostic value is more than the standard value. (2 trip detection logic)
- P0420Diagnostic value is more than the standard value. (2 trip detection logic)
- P0441While engine running, following conditions successively met: · The pressure difference between non-purge and...
- P0451The difference between the canister pressure sensor output value and the manifold absolute pressure sensor...
- P0452EVAP pressure sensor less than 0.973 V for 1 second.
- P0453EVAP pressure sensor more than 4.095 V for 1 second.
- P0455Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure is measured....
- P0456Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure is measured....
- P0458The voltage of purge valve circuit is low for 2.5 seconds or more. (2 trip detection logic)
- P0459The voltage of purge valve circuit is high for 2.5 seconds or more. (2 trip detection logic)
- P0461Compared with the estimated fuel consumption, the actual variation in the fuel sender gauge assembly signal...
- P0462Fuel sender gauge assembly voltage is less than 0.35 V for 2.5 seconds or more. (2 trip detection logic)
- P0463Fuel sender gauge assembly voltage is higher than 7.183 V for 1 second or more. (2 trip detection logic)
- P0500The vehicle speed signal from the driving wheels is 300 km/h or more for 2.5 seconds or more. (1 trip...
- P0500The vehicle speed signal from the driving wheels is 300 km/h or more for 2.5 seconds or more. (1 trip...
- P0506The engine speed is not close to the target engine speed for 30 seconds or more ((Actual engine speed -...
- P0507The engine speed is not close to the target engine speed for 30 seconds or more ((Actual engine speed -...
- P050AThe engine speed does not achieve the target engine speed for 7 seconds with engine cooled down. (2 trip...
- P050BThe ignition timing is not retarded for 7 seconds, despite rapid warming control of the catalyst (to retard...
- P0512Starter signal remains input for 30 seconds or more after engine started. (1 trip detection logic)
- P0560Back up power source terminal voltage is 3.5 V or less with the engine running for 2.5 seconds or more. (1...
- P0560Backup power source terminal voltage is 3.5 V or less with the engine running for 2.5 seconds or more. (1...
- P0562The voltage of BATT is less than 10.8 V for 30 seconds or more when engine speed is 1500 rpm or more. (1 trip...
- P0562The voltage of BATT is less than 10.8 V for 30 seconds or more when engine speed is 1500 rpm or more. (1 trip...
- P0563The voltage of BATT is 16.2 V or more for 30 seconds or more when engine speed is 1500 rpm or more. (1 trip...
- P0563The voltage of BATT is 16.2 V or more for 30 seconds or more when engine speed is 1500 rpm or more. (1 trip...
- P0604P0604
- P0605P0605
- P0606P0606
- P060AP060A
- P060BP060B
- P0616No starter signal is input when engine started. (1 trip detection logic)
- P0617Starter signal remains input after engine started. (1 trip detection logic)
- P062DWhen injection is finished in all cylinders, the diagnostic signal from the EDU does not change (open or...
- P062DWhen injection is finished in all cylinders, the diagnostic signal from the EDU does not change (open or...
- P062FP062F
- P0700Automatic transmission system malfunction received from the TCM (1 trip detection logic)
- P081AShort in ST CUT relay circuit is detected. (1 trip detection logic)
- P0851for Manual Transmission No non-neutral position detected in shift change running state (judged based on...
- P0852for Manual Transmission No neutral position detected in shift change running state (judged based on changes...
- P1109ISC learning value is 95% or more of the maximum learning ISC learning value, and 50% or more deposit is...
- P1160After setting throttle valve opening angle at 40% in throttle actuator control, the change in opening angle...
- P1170Although a DTC is stored for a rich or lean condition, the amount of fuel trim during direct injection is...
- P117BAlthough a DTC is stored for a rich or lean condition, the amount of fuel trim during port injection is...
- P1235When fuel pump for high pressure is operating, the diagnostic signal from injector driver (EDU) does not...
- P1261When the injection of No. 1 cylinder is finished, the diagnostic signal from injector driver (EDU) does not...
- P1261When the injection of No. 1 cylinder is finished, the diagnostic signal from injector driver (EDU) does not...
- P1262When the injection of No. 2 cylinder is finished, the diagnostic signal from injector driver (EDU) does not...
- P1262When the injection of No. 2 cylinder is finished, the diagnostic signal from injector driver (EDU) does not...
- P1263When the injection of No. 3 cylinder is finished, the diagnostic signal from injector driver (EDU) does not...
- P1263When the injection of No. 3 cylinder is finished, the diagnostic signal from injector driver (EDU) does not...
- P1264When the injection of No. 4 cylinder is finished, the diagnostic signal from injector driver (EDU) does not...
- P1264When the injection of No. 4 cylinder is finished, the diagnostic signal from injector driver (EDU) does not...
- P1449The canister pressure sensor output value has rapidly changed.
- P1451A blockage in the EVAP system pipe is detected.
- P1603After monitoring for startability problems (P1604) finishes and starting the engine, with the engine running,...
- P1603After monitoring for startability problems (P1604) finishes and starting the engine, with the engine running,...
- P1603After monitoring for startability problems (P1604) finishes and starting the engine, with the engine running,...
- P1604One of the following conditions is met (1 trip detection logic): · The engine speed is less than 500 rpm with...
- P1604One of the following conditions is met (1 trip detection logic): · The engine speed is less than 500 rpm with...
- P1604One of the following conditions is met (1 trip detection logic): · The engine speed is less than 500 rpm with...
- P1604One of the following conditions is met (1 trip detection logic): · The engine speed is less than 500 rpm with...
- P2096With warm engine and stable air fuel ratio feedback, sub fuel trim considerably in error to lean side (2 trip...
- P2097With warm engine and stable air fuel ratio feedback, sub fuel trim considerably in error to rich side (2 trip...
- P2101One of the following conditions is met (1 trip detection logic): · Throttle actuator current is 8 A or more....
- P2101One of the following conditions is met (1 trip detection logic): · Throttle actuator current is 8 A or more....
- P2102ECM is turning ETCS relay on but throttle actuator power supply voltage is 5 V or less. (1 trip detection...
- P2102ECM is turning ETCS relay on but throttle actuator power supply voltage is 5 V or less. (1 trip detection...
- P2103ECM is turning ETCS relay off but throttle actuator power supply voltage is 5 V or more. (1 trip detection...
- P2103ECM is turning ETCS relay off but throttle actuator power supply voltage is 5 V or more. (1 trip detection...
- P2109One of the following conditions is met (1 trip detection logic): · The throttle position sensor opening angle...
- P2119The throttle valve opening angle continues to vary greatly from the target opening angle. (1 trip detection...
- P2122VPA voltage is less than 0.213 V. (1 trip detection logic)
- P2123VPA voltage is 4.737 V or more. (1 trip detection logic)
- P2127VPA2 voltage is less than 0.213 V. (1 trip detection logic)
- P2128VPA2 voltage is 4.737 V or more. (1 trip detection logic)
- P2135Deviation in voltages of VTA1 and VTA2 exceed thresholds for 0.212 seconds or more. (1 trip detection logic)
- P2138Difference in the signals from VPA and VPA2 exceeds the threshold. (1 trip detection logic)
- P2158P2158
- P2195Lambda is less than 0.85 for 10 seconds in air fuel ratio feed back control (2 trip detection logic)
- P2196Lambda is more than 1.15 for 10 seconds in air fuel ratio feed back control (2 trip detection logic)
- P219AOne of the following conditions is met (2 trip detection logic): · Air fuel ratio sensor signal fluctuates in...
- P2270Heated oxygen sensor voltage is less than 0.55 V for 15 seconds or more. (2 trip detection logic)
- P2271Heated oxygen sensor voltage is more than 0.15 V for 0.5 seconds or more. (2 trip detection logic)
- P2401, P2402, P2419 and P2420 stored when one of following conditions met during EVAP monitor: · Leak...
- P2402P2402
- P2404Leak detection pump ending pressure is more than the threshold. The difference between the leak detection...
- P2419P2419
- P2420P2420
- P2610One of the following conditions is met (2 trip detection logic): Timer diagnosis · [(Engine ECU counter -...
- U0073Bus off state for 0.436 seconds or more (1 trip detection logic)
- U0101No communication between ECM and TCM for 0.5 seconds or more (1 trip detection logic)
- U0122No communication between ECM and skid control ECU for 0.5 seconds or more (1 trip detection logic)
- U0155No communication between ECM and combination meter assembly for 0.5 seconds or more (1 trip detection logic)
- U0402Invalid data received from TCM for 2 seconds or more (1 trip detection logic)
- U0416Invalid data received from skid control ECU for 2 seconds or more (1 trip detection logic)
- U0423Invalid data received from combination meter assembly for 2 seconds or more (1 trip detection logic)
- P0500DTC P0500 is detected in SFI system.
- U0073Bus off state for 0.436 seconds or more (1 trip detection logic)
- U0101No communication between ECM and TCM for 0.5 seconds or more (1 trip detection logic)
- U0122No communication between ECM and skid control ECU for 0.5 seconds or more (1 trip detection logic)
- U0155No communication between ECM and combination meter assembly for 0.5 seconds or more (1 trip detection logic)
- U0402Invalid data received from TCM for 2 seconds or more (1 trip detection logic)
- U0416Invalid data received from skid control ECU for 2 seconds or more (1 trip detection logic)
- U0423Invalid data received from combination meter assembly for 2 seconds or more (1 trip detection logic)
- B10161. Ignition switch is turned to ON 2. Shift lock circuit open, short to B+, or short to ground 3. For 3...
- P06011. Ignition switch is turned to ON 2. TCM internal malfunction 3. - 4. 1-trip detection logic
- P062F1. Ignition switch is turned to ON 2. TCM internal error 3. - 4. 1-trip detection logic
- P07071. The output speed sensor SP2 is normal, not learning control prohibited status, and the vehicle speed is 30...
- P07081. Not learning control prohibited status 2. 2 or more shift positions are detected at the same time 3....
- P07111. Detects that the park/neutral position switch assembly is normal, the shift position sensor is in D, the...
- P07121. Not learning control prohibited status 2. The oil temperature sensor input voltage is 0.05 V or less 3....
- P07131. Park/neutral position switch assembly is normal, and shift lever is in D or R for 1 min. or more Not...
- P07171. The shift solenoid valve (S1, S2, S3, S4, SR, SL1, SL2, SLT), output speed sensor SP2 and shift position...
- P07221. The shift solenoid valve (S1, S2, S3, S4, SR, SL1, SL2, SLT), input speed sensor NT and shift position...
- P07291. While driving with the shift lever in D, the ATF temperature 20°C (68°F) or more, and coolant temperature...
- P07511. While driving with the shift lever in D, the ATF temperature 20°C (68°F) or more, and coolant temperature...
- P07521. While driving with the shift lever in D, the ATF temperature 20°C (68°F) or more, and coolant temperature...
- P07561. While driving with the shift lever in D, the ATF temperature 20°C (68°F) or more, and coolant temperature...
- P07571. While driving with the shift lever in D, the ATF temperature 20°C (68°F) or more, and coolant temperature...
- P07611. While driving with the shift lever in D, the ATF temperature 20°C (68°F) or more, and coolant temperature...
- P07621. While driving with the shift lever in D, the ATF temperature 20°C (68°F) or more, and coolant temperature...
- P07661. While driving with the shift lever in D, the ATF temperature 20°C (68 °F) or more, and coolant temperature...
- P07671. While driving with the shift lever in D, the ATF temperature 20°C (68 °F) or more, and coolant temperature...
- P07761. While driving with the shift lever in D, the ATF temperature 20°C (68 °F) or more, and coolant temperature...
- P07811. While driving with the shift lever in D, the ATF temperature 20°C (68°F) or more, and coolant temperature...
- P08821. The engine speed and input speed sensor NT are 400 rpm or more, and the CAN communication and input speed...
- P08941. While driving with the shift lever in D, the ATF temperature 10°C or more, and coolant temperature 40°C or...
- P09611. Not learning control prohibited status Not open or short in the shift solenoid valve SL1 circuit 2. The...
- P09621. Not learning control prohibited status 1 second or more has elapsed after turning shift solenoid valve SL1...
- P09631. Not learning control prohibited status 1 second or more has elapsed after turning shift solenoid valve SL1...
- P09651. Not learning control prohibited status 2. The difference between the shift solenoid valve SL2 operational...
- P09661. Not learning control prohibited status 1 second or more has elapsed after turning shift solenoid valve SL2...
- P09671. Not learning control prohibited status 1 second or more has elapsed after turning shift solenoid valve SL2...
- P09731. Not learning control prohibited status 2. During shift solenoid valve S1 on signal is output, the TCM S1...
- P09741. Not learning control prohibited status 2. During shift solenoid valve S1 off signal is output, the TCM S1...
- P09761. Not learning control prohibited status 2. During shift solenoid valve S2 on signal is output, the TCM's S2...
- P09771. Not learning control prohibited status 2. During shift solenoid valve S2 off signal is output, the TCM's...
- P09791. Not learning control prohibited status 2. During shift solenoid valve S3 on signal is output, the TCM's S3...
- P09801. Not learning control prohibited status 2. During shift solenoid valve S3 off signal is output, the TCM's...
- P09821. Not learning control prohibited status 2. During shift solenoid valve S4 on signal is output, the TCM's S4...
- P09831. Not learning control prohibited status 2. During shift solenoid valve S4 off signal is output, the TCM's...
- P09851. Not learning control prohibited status 2. During shift solenoid valve SR on signal is output, the TCM's SR...
- P09861. Not learning control prohibited status 2. During shift solenoid valve SR off signal is output, the TCM's...
- P160A1. Ignition switch is turned to ON 2. TCM internal malfunction. When the information recorded inside the TCM...
- P18171. Shift position sensor is normal, and not in learning control prohibited status. 2. The shift lever is in...
- P27141. While driving with the shift lever in D, the ATF temperature 10°C or more, and coolant temperature 40°C or...
- P27191. Not learning control prohibited status 2. The difference between the shift solenoid valve SLT operational...
- P27201. Not learning control prohibited status 2. 1 second or more has elapsed after turning shift solenoid valve...
- P27211. Not learning control prohibited status 2. 1 second or more has elapsed after turning shift solenoid valve...
- P27571. The following conditions are met: (a) Not learning control prohibited status (b) 4 seconds or more have...
- P27581. The following conditions are met: (a) Not learning control prohibited status (b) 4 seconds or more have...
- P27621. Not learning control prohibited status. Not open or short in the shift solenoid valve SLU/DSU circuit. 2....
- P27631. Not learning control prohibited status Not malfunction with the shift solenoid valve SLU/DSU circuit...
- P27641. Not learning control prohibited status Not malfunction with the shift solenoid valve SLU/DSU circuit...
- U00731. Ignition voltage is 9 V or more, and this condition continues for 1 second or more. 2. Data reception and...
- U01001. CAN bus is normal. 2. Signal from the ECM is interrupted. 3. 500 ms, 800 ms, 2000 ms (differs depending on...
- U01221. CAN bus is normal. 2. Signal from the skid control ECU (brake actuator assembly) is interrupted. 3. 800 ms...
- U01401. CAN bus is normal. 2. Signal from the main body ECU (network gateway ECU) is interrupted. 3. 800 ms, 20000...
- U01551. CAN bus is normal. 2. Signal from combination meter assembly is interrupted. 3. 2000 ms 4. 1-trip...
- U04011. CAN bus is normal. 2. Reception of malfunction signal from the ECM. 3. 50 times 4. 1-trip detection logic
- U04161. CAN bus is normal. 2. Reception of malfunction signal from the skid control ECU (brake actuator assembly)....
- U04221. CAN bus is normal. 2. Reception of malfunction signal from the main body ECU (network gateway ECU). 3. 40...
- U04231. CAN bus is normal. 2. Reception of malfunction signal from the combination meter assembly. 3. 40 times 4....
- B1247In diagnostic mode, an applicable RDA signal cannot be received within 10 seconds with the ignition switch ON.
- C2111/11 Tire pressure warning valve and transmitters stop transmitting signals
- C2112/12 Tire pressure warning valve and transmitters stop transmitting signals
- C2113/13 Tire pressure warning valve and transmitters stop transmitting signals
- C2114/14 Tire pressure warning valve and transmitters stop transmitting signals
- C2121/21 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2122/22 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2123/23 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2124/24 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2126/26 After ID registration is completed, ECU does not receive radio waves from transmitters whose IDs are stored...
- C2141/41 If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will...
- C2142/42 If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will...
- C2143/43 If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will...
- C2144/44 If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will...
- C2171/71 Transmitter ID code is not registered. (When an ID code is unregistered for 3 minutes or more)
- C2176/76 Malfunction in the tire pressure warning ECU and receiver internal circuit
- C2177/77 All conditions below are met: · During initialization · Tire pressure warning valve and transmitter is not in...
- C2179/79 Communication between the main body ECU (network gateway ECU) and tire pressure warning ECU and receiver is...
- C2181/81 Test mode procedure is performed.
- C2182/82 Test mode procedure is performed.
- C2183/83 Test mode procedure is performed.
- C2184/84 Test mode procedure is performed.
- C2198/98 Test mode procedure is performed.
- C1201Engine control system malfunction signal continues for 5 seconds while the vehicle is being driven.
- C1225Solenoid valve signal does not match the check result.
- C1226Solenoid valve signal does not match the check result.
- C1227Solenoid valve signal does not match the check result.
- C1228Solenoid valve signal does not match the check result.
- C1231When the +BS terminal voltage is between 9.6 and 16.5 V, the steering sensor malfunction signal is received.
- C1234Internal failure of the skid control ECU (Yaw rate sensor).
- C1237Any of the following is detected: 1. Discrepancy among four wheel speed sensor output. 2. Abnormal pulse...
- C1237Any of the following is detected: 1. Discrepancy among four wheel speed sensor output. 2. Abnormal pulse...
- C1241Any of the following is detected: 1. The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage...
- C1241Any of the following is detected: 1. The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage...
- C1246Any of the following is detected: 1. The voltage of the sensor signal is out of range (below 0.129 V, above...
- C1249Any of the following is detected: · The vehicle speed is 10 km/h (6 mph) or more, the accelerator pedal is...
- C1271Detected only during Test Mode.
- C1271Detected only during Test Mode.
- C1272Detected only during Test Mode.
- C1272Detected only during Test Mode.
- C1273Detected only during Test Mode.
- C1274Detected only during Test Mode.
- C1275Detected only during Test Mode.
- C1275Detected only during Test Mode.
- C1276Detected only during Test Mode.
- C1276Detected only during Test Mode.
- C1277Detected only during Test Mode.
- C1277Detected only during Test Mode.
- C1278Detected only during Test Mode.
- C1278Detected only during Test Mode.
- C1288ECM does not match.
- C1294C1294
- C1300Internal failure of the skid control ECU.
- C1330An open or short in the speed sensor signal circuit.
- C1330An open or short in the speed sensor signal circuit.
- C1331An open or short in the speed sensor signal circuit.
- C1331An open or short in the speed sensor signal circuit.
- C1332An open or short in the speed sensor signal circuit.
- C1333An open or short in the speed sensor signal circuit.
- C1419Internal failure of the skid control ECU (Acceleration sensor).
- C1464An abnormal signal is received from a wheel speed sensor.
- C1464An abnormal signal is received from a wheel speed sensor.
- C1465An abnormal signal is received from a wheel speed sensor.
- C1465An abnormal signal is received from a wheel speed sensor.
- C1466An abnormal signal is received from a wheel speed sensor.
- C1467An abnormal signal is received from a wheel speed sensor.
- C1468Solenoid valve signal does not match the check result.
- C1469Solenoid valve signal does not match the check result.
- C146ASolenoid valve signal does not match the check result.
- C146BSolenoid valve signal does not match the check result.
- C146CAny of the following is detected: 1. When the ABS motor relay is actuated, voltage is not supplied to the...
- C146EEither of the following is detected: 1. A solenoid relay drive circuit in the skid control ECU is...
- C1472Internal failure of the skid control ECU (Lateral G sensor).
- C1474Internal failure of the skid control ECU (Forward and backward G sensor).
- C1492Clutch switch system circuit has a malfunction
- C1493Clutch switch system circuit has a malfunction
- C1494Back-up switch system circuit has a malfunction
- C1495Back-up switch system circuit has a malfunction
- U0073The +BS terminal voltage is between 9.6 and 16.5 V and bus off is judged for 0.1 seconds or more.
- U0073The +BS terminal voltage is between 9.6 and 16.5 V and bus off is judged for 0.1 seconds or more.
- U0100The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals...
- U0100The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals...
- U0101U0101
- U0101U0101
- U0126The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals...
- U0126The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals...
- U0140The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle is being driven, and signals from the...
- C1511A torque sensor (TRQ1) signal error or stop
- C1512A torque sensor (TRQ2) signal error or stop
- C1513The deviation between torque sensor TRQ1 and TRQ2 exceeds a specified value.
- C1514A torque sensor power supply voltage error
- C1515Torque sensor zero point calibration has not been performed.
- C1516Torque sensor zero point calibration is incomplete due to the steering wheel being touched during calibration.
- C1517Temporary control due to a malfunction related to the torque sensor continues for long time.
- C1521Motor overcurrent
- C1522A motor current sensor malfunction
- C1523An excessively large current deviation
- C1524A short or open in the motor circuit or abnormal voltage or current in the motor circuit
- C1525Rotation angle sensor value initialization has not been performed.
- C1526Rotation angle sensor value initialization is incomplete due to the steering wheel being touched during...
- C1528A rotation angle sensor malfunction
- C1531An ECU internal malfunction (CPU malfunction)
- C1532An ECU internal malfunction (peripheral circuit malfunction)
- C1533An ECU internal malfunction (substrate temperature sensor malfunction)
- C1534An ECU internal malfunction (EEPROM error)
- C1541The vehicle speed signals malfunction
- C1551An IG power supply circuit malfunction inside the ECU
- C1552A PIG power supply circuit malfunction inside the ECU
- C1554A power supply relay circuit malfunction
- C1555A motor relay malfunction
- C1581The assist map is not written in the power steering ECU assembly.
- C1581The assist map is not written in the power steering ECU assembly.
- C1582Data that does not match the vehicle specification is received through CAN communication.
- C1582Data that does not match the vehicle specification is received through CAN communication.
- C1583Correct information cannot be received.
- U0100Lost communication with the ECM/PCM "A"
- U0122Lost communication with the brake system control module
- U0416The brake system control module signal malfunction
- B2781One of the following conditions is met (1-trip detection logic*1): · The steering lock/unlock position sensor...
- B2782Either condition is met (1-trip detection logic*1): · The steering lock motor activation command circuit has...
- B2788Mismatch between the steering lock actuator assembly (steering lock ECU) IGN1 input from the LIN...
- P0516· Engine speed is 500 r/min or more, battery voltage is 10.9 V or more, and 1 second or more have elapsed...
- P0517· Engine speed is 500 r/min or more, battery voltage is 10.9 V or more, and 1 second or more have elapsed...
- P0562Either of the following conditions is met for 30 seconds: Condition 1 · The engine speed is 500 rpm or more....
- P0563Either of the following conditions is met for 30 seconds: Condition 1 · The final output duty cycle of...
- P065AEither of the following conditions is met for 512 ms: Condition 1 · A generator assembly internal failure...
- P0A3BA generator assembly internal failure flag (high-temperature alert) is set and the internal temperature of...
- P1530· Engine speed is 500 r/min or more, battery voltage is 10.9 V or more, and 1 second or more have elapsed...
- P1531· Engine speed is 500 r/min or more, battery voltage is 10.9 V or more, and 1 second or more have elapsed...
- P1532· Ignition switch ON · Current sensor fixing diagnosis: The difference between the maximum and minimum...
- P1C00The IBS information about the abnormality in the battery temperature sensor, battery voltage sensor or...
- U0077Both of the following conditions are met for 1.24 seconds: · The battery voltage is 10.9 V or more. · LIN...
- U1712Both of the following conditions are met for 2 seconds: · The battery voltage is 10.9 V or more. · The...
- U171FEither of the following conditions is met for 2 seconds: Condition 1 · The battery voltage is 10.9 V or more....
- B1010Main body ECU (network gateway ECU) internal error
- B1011When BMPX voltage is 8.3 V or less, or 16.7 V or more (BMPX circuit malfunction)
- B1012When BECU voltage is 8.3 V or less, or 16.7 V or more (BECU circuit malfunction)
- B1013When IG voltage is 8.3 V or less, or 16.7 V or more (IG circuit malfunction)
- B1014When ACC voltage is 8.3 V or less, or 16.7 V or more (ACC circuit malfunction)
- B2321Lost communication between the multiplex network master switch assembly and the main body ECU (network...
- B2325The main body ECU (network gateway computer) detects errors in door LIN bus communication lines at 2.6-second...
- B2785The certification ECU (smart key ECU assembly) detects a LIN communication error (+B short, GND short,...
- B2786This DTC is stored when communication between the certification ECU (smart key ECU assembly) and the steering...
- B2789No communication between the certification ECU (smart key ECU assembly) and the ID code box (immobiliser code...
- B1242In diagnostic mode, applicable RDA signal cannot be received 3 times in succession after the PRG signal is...
- B1242In diagnostic mode, applicable RDA signal cannot be received 3 times in succession after the PRG signal is...
- B2271Either condition is met (1-trip detection logic*1): · The IG1 or IG2 drive circuit in the certification ECU...
- B2274Malfunction in the ACC relay activation circuit in the certification ECU (smart key ECU assembly) or the...
- B2275· Circuit malfunction detected in the engine start permission output circuit inside the certification ECU...
- B2276When an input malfunction occurs in the ACC relay cut input signal circuit inside the certification ECU...
- B2277The water submersion detection circuit in the certification ECU (smart key ECU assembly) detects water...
- B2282Mismatch between the vehicle speed signal from the direct line sent by the brake actuator assembly (skid...
- B2283Either condition is met (vehicle speed sensor malfunction is detected) (1-trip detection logic*1): · Vehicle...
- B2284The brake signal information from the direct line and the brake signal information from the ECM via CAN...
- B2285The steering lock position signal sent by the steering lock ECU via direct line and the steering lock...
- B2286The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN...
- B27A1An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front...
- B27A2An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front...
- B27A5An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and indoor...
- B27A6An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 2...
- B27A7An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 3...
- B27A8An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and...
- P0335The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN...
- U0073CAN communication system malfunction (1-trip detection logic*).
- U0100CAN communication malfunction between the certification ECU (smart key ECU assembly) and ECM (1-trip...
- U0101CAN communication malfunction between the certification ECU (smart key ECU assembly) and TCM (1-trip...
- U0122CAN communication malfunction between the certification ECU (smart key ECU assembly) and brake actuator...
- U0140CAN communication malfunction between the certification ECU (smart key ECU assembly) and main body ECU...
- U0155CAN communication malfunction between the certification ECU (smart key ECU assembly) and combination meter...
- U0401CAN communication malfunction between the certification ECU (smart key ECU assembly) and ECM (1-trip...
- U0422CAN communication malfunction between the certification ECU (smart key ECU assembly) and main body ECU...
- B1571The ECM reference code and reference code from the certification ECU (smart key ECU assembly) do not match (1...
- B1572When there is a problem in communication between the ID code box (immobiliser code ECU)*1 or certification...
- B1576· Internal malfunction in the ECM (1 trip detection logic*). · When the ROM in the ECM cannot be accessed...
- B1577· Internal malfunction in the certification ECU (smart key ECU assembly) (1 trip detection logic*). · When...
- B2784The transponder key amplifier coil built into the engine switch is open or shorted (determined by...
- B278AA short to GND in the power supply of the transponder key amplifier of the engine switch (VC5 - VC5) (1 trip...
- B278DOne of the following conditions is met: · The certification ECU (smart key ECU assembly) recognizes that the...
- B1401The main body ECU (network gateway ECU) reference code and reference code from the combination meter assembly...
- B1402When an improper key (a key not registered in the main body ECU (network gateway ECU)) is inserted into the...
- B1405The main body ECU (network gateway ECU) reference code and reference code from the transponder key ECU...
- B1406Internal malfunction in the transponder key ECU assembly when the ROM in the transponder key ECU assembly...
- B1407When there is a problem in communication between the main body ECU (network gateway ECU) and the combination...
- B1408Internal malfunction in the combination meter assembly.
- B1409When there is a problem in communication between the main body ECU (network gateway ECU) and the transponder...
- B1410When there is a problem in communication between the key and the main body ECU (network gateway ECU).
- B1411B1411
- B1571The main body ECU (network gateway ECU) reference code and reference code from the ECM do not match.
- B1572When there is a problem in communication between the main body ECU (network gateway ECU) and ECM.
- B1576· Internal malfunction in the ECM. · When the ROM in the ECM cannot be accessed when registering a key.
- B1577· Internal malfunction in the main body ECU (network gateway ECU). · When the ROM in the main body ECU...
- B1578· The combination meter assembly reference code and the reference code from the main body ECU (network...
- B1500When combination meter detects fuel sender gauge malfunction
- B1509An open or short in the thermistor assembly circuit.
- U0073Lost Communication with Each ECU
- U0100ECM communication error
- U0122Skid control ECU (brake actuator assembly) communication error
- U0131Power steering ECU assembly communication error
- U0140Main body ECU (network gateway ECU) communication error
- U0151Airbag sensor assembly communication error
- B1000Airbag ECU assembly malfunction
- B11F1Deployment of horn button assembly (driver side squib), instrument panel passenger airbag assembly (front...
- B11F6Deployment of front seat airbag assembly RH or LH (front side squib RH or LH) and curtain shield airbag...
- B1610· Front airbag sensor RH malfunction · Airbag ECU assembly malfunction
- B1612· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1613· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1615· Front airbag sensor LH malfunction · Airbag ECU assembly malfunction
- B1617· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1618· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B161A· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1620· Side No. 2 airbag sensor assembly RH malfunction · Airbag ECU assembly malfunction
- B1622· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1623· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1625· Side No. 2 airbag sensor assembly LH malfunction · Airbag ECU assembly malfunction
- B1627· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1628· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1630· Rear airbag sensor RH malfunction · Airbag ECU assembly malfunction
- B1632· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1633· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1635· Rear airbag sensor LH malfunction · Airbag ECU assembly malfunction
- B1637· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1638· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1642· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1647· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1651· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1660· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1675· No. 2 airbag sensor assembly malfunction. · Airbag ECU assembly malfunction.
- B1678· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1679· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1690· Side airbag sensor assembly RH malfunction · Airbag ECU assembly malfunction
- B1692· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1693· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1695· Side airbag sensor assembly LH malfunction · Airbag ECU assembly malfunction
- B1697· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1698· The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B16F2· Improper installation of front airbag sensor RH · Airbag ECU assembly malfunction
- B16F3· Improper installation of front airbag sensor LH · Airbag ECU assembly malfunction
- B16F4· Improper installation of side No. 2 airbag sensor assembly RH · Airbag ECU assembly malfunction
- B16F5· Improper installation of side No. 2 airbag sensor assembly LH · Airbag ECU assembly malfunction
- B16F6· Improper installation of rear airbag sensor RH · Airbag ECU assembly malfunction
- B16F7· Improper installation of rear airbag sensor LH · Airbag ECU assembly malfunction
- B16F8· Improper installation of No. 2 airbag sensor assembly. · Airbag ECU assembly malfunction.
- B16F9· Improper installation of side airbag sensor assembly RH · Airbag ECU assembly malfunction
- B16FA· Improper installation of side airbag sensor assembly LH · Airbag ECU assembly malfunction
- B1800· The airbag ECU assembly receives a line short circuit signal in the driver side squib circuit during...
- B1801· The airbag ECU assembly receives an open circuit signal in the driver side squib circuit. · Spiral cable...
- B1802· The airbag ECU assembly receives a short circuit to ground signal in the driver side squib circuit. ·...
- B1803· The airbag ECU assembly receives a short circuit to B+ signal in the driver side squib circuit. · Spiral...
- B1805· The airbag ECU assembly receives a line short circuit signal in the front passenger side squib circuit...
- B1806· The airbag ECU assembly receives an open circuit signal in the front passenger side squib circuit. · Front...
- B1807· The airbag ECU assembly receives a short circuit to ground signal in the front passenger side squib...
- B1808· The airbag ECU assembly receives a short circuit to B+ signal in the front passenger side squib circuit. ·...
- B1810· The airbag ECU assembly receives a line short circuit signal in the driver side squib 2nd step circuit...
- B1811· The airbag ECU assembly receives an open circuit signal in the driver side squib 2nd step circuit. · Spiral...
- B1812· The airbag ECU assembly receives a short circuit to ground signal in the driver side squib 2nd step...
- B1813· The airbag ECU assembly receives a short circuit to B+ signal in the driver side squib 2nd step circuit. ·...
- B1815· The airbag ECU assembly receives a line short circuit signal in the front passenger side squib 2nd step...
- B1816· The airbag ECU assembly receives an open circuit signal in the front passenger side squib 2nd step circuit....
- B1817· The airbag ECU assembly receives a short circuit to ground signal in the front passenger side squib 2nd...
- B1818· The airbag ECU assembly receives a short circuit to B+ signal in the front passenger side squib 2nd step...
- B1820· The airbag ECU assembly receives a line short circuit signal in the front side squib RH circuit during...
- B1821· The airbag ECU assembly receives an open circuit signal in the front side squib RH circuit. · Front side...
- B1822· The airbag ECU assembly receives a short circuit to ground signal in the front side squib RH circuit. ·...
- B1823· The airbag ECU assembly receives a short circuit to B+ signal in the front side squib RH circuit. · Front...
- B1825· The airbag ECU assembly receives a line short circuit signal in the front side squib LH circuit during...
- B1826· The airbag ECU assembly receives an open circuit signal in the front side squib LH circuit. · Front side...
- B1827· The airbag ECU assembly receives a short circuit to ground signal in the front side squib LH circuit. ·...
- B1828· The airbag ECU assembly receives a short circuit to B+ signal in the front side squib LH circuit. · Front...
- B1830· The airbag ECU assembly receives a line short circuit signal in the curtain shield squib RH circuit during...
- B1831· The airbag ECU assembly receives an open circuit signal in the curtain shield squib RH circuit. · Curtain...
- B1832· The airbag ECU assembly receives a short circuit to ground signal in the curtain shield squib RH circuit. ·...
- B1833· The airbag ECU assembly receives a short circuit to B+ signal in the curtain shield squib RH circuit. ·...
- B1835· The airbag ECU assembly receives a line short circuit signal in the curtain shield squib LH circuit during...
- B1836· The airbag ECU assembly receives an open circuit signal in the curtain shield squib LH circuit. · Curtain...
- B1837· The airbag ECU assembly receives a short circuit to ground signal in the curtain shield squib LH circuit. ·...
- B1838· The airbag ECU assembly receives a short circuit to B+ signal in the curtain shield squib LH circuit. ·...
- B1860· The airbag ECU assembly receives a line short circuit signal in the driver side knee airbag squib circuit...
- B1861· The airbag ECU assembly receives an open circuit signal in the driver side knee airbag squib circuit. ·...
- B1862· The airbag ECU assembly receives a short circuit to ground signal in the driver side knee airbag squib...
- B1863· The airbag ECU assembly receives a short circuit to B+ signal in the driver side knee airbag squib circuit....
- B1900· The airbag ECU assembly receives a line short circuit signal in the front pretensioner squib RH circuit...
- B1901· The airbag ECU assembly receives an open circuit signal in the front pretensioner squib RH circuit. · Front...
- B1902· The airbag ECU assembly receives a short circuit to ground signal in the front pretensioner squib RH...
- B1903· The airbag ECU assembly receives a short circuit to B+ signal in the front pretensioner squib RH circuit. ·...
- B1905· The airbag ECU assembly receives a line short circuit signal in the front pretensioner squib LH circuit...
- B1906· The airbag ECU assembly receives an open circuit signal in the front pretensioner squib LH circuit. · Front...
- B1907· The airbag ECU assembly receives a short circuit to ground signal in the front pretensioner squib LH...
- B1908· The airbag ECU assembly receives a short circuit to B+ signal in the front pretensioner squib LH circuit. ·...
- U0073Control Module Communication Bus OFF
- B1430/21 Open in room temperature sensor circuit
- B1431/-21
- B1432/22 Open in ambient temperature sensor circuit
- B1433/-22
- B1434/23 Open in evaporator sensor circuit
- B1435/-23
- B1436/45 Open in passenger side air mix damper position sensor circuit
- B1437/-45
- B1438/49 Open in Air Outlet Damper Position Sensor Circuit
- B1439/-49
- B1440/41 Open in driver side air mix damper position sensor circuit
- B1441/E45 Passenger side air mix damper control servomotor circuit
- B1442/-41
- B1443/E49 Air outlet damper Control servo motor circuit
- B1446/E41 Driver side air mix damper position sensor circuit
- B14A1/25 Open in Solar Sensor Circuit
- B14A2/-25
- U0073Control Module Communication Bus Off
- U0100Lost Communication With ECM/PCM "A"
- U0101Lost Communication With TCM
- U0122Lost Communication with Vehicle Dynamics Control Module
- U0140Lost Communication with Body Control Module
- U0155Lost Communication With Instrument Panel Cluster Control Module
- U0401Invalid Data Received from ECM/PCM "A"
- U0402Invalid Data Received from TCM
- U0416Invalid Data Received from Vehicle Dynamics Control Module
- U0422Invalid Data Received from Body Control Module
- U0423Invalid Data Received from Instrument Panel Cluster Control Module
- B2311· Power window regulator motor assembly malfunction (pulse sensor) · Power window regulator master switch...
- B2312· The power window regulator master switch is stuck · Power window regulator master switch assembly held in...
- B2313· Power window regulator master switch assembly not initialized · Power window regulator motor assembly (for...
- B2314· Power window regulator motor assembly malfunction (pulse sensor) · Power window regulator switch assembly...
- B2315· The power window regulator switch is stuck · Power window regulator switch assembly held in same position...
- B2316· Power window regulator switch assembly not initialized · Power window regulator motor assembly (for front...
Common jobs · FA20 (14)
- Read / clear codes
- Timing chain: installation
- Ignition coil: removal
- Drive belt: on-vehicle inspection · removal · installation
- Coolant: replacement
- Water pump: on-vehicle inspection · removal · installation
- Thermostat: inspection · removal · installation
- Radiator: on-vehicle inspection · removal · installation
- Fuel pump: on-vehicle inspection · inspection · removal · disassembly · reassembly · installation
- Injectors: inspection · removal · installation
- Throttle body: inspection · removal · installation
- Cylinder head gasket: removal · installation
- Cylinder head: disassembly · reassembly
- Starter: inspection · removal · disassembly · reassembly · installation
Common jobs · chassis & body (9)
- Alternator: inspection · removal · disassembly · reassembly · installation
- ATF: replacement · adjustment
- Clutch: inspection · removal · installation
- Front brakes: inspection · removal · disassembly · reassembly · installation
- Rear brakes: inspection · removal · disassembly · reassembly · installation
- Brake fluid: on-vehicle inspection · bleeding
- Parking brake: inspection
- Wheel alignment: adjustment
- Headlights: removal · disassembly · reassembly · installation · adjustment
Repair Manual
General251 documents
Engine / Hybrid System454 documents
Drivetrain245 documents
Suspension98 documents
Brake194 documents
Steering82 documents
Audio / Visual / Telematics75 documents
Power Source / Network110 documents
Vehicle Interior699 documents
Vehicle Exterior422 documents
New Car Features
General31 documents
Engine / Hybrid System67 documents
Drivetrain22 documents
Suspension15 documents
Brake16 documents
Steering12 documents
Audio / Visual / Telematics15 documents
Power Source / Network15 documents
Vehicle Interior76 documents
Vehicle Exterior43 documents