Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR
BM2090E _01 Vehicle Exterior _060720 BODY PANEL _0297850 FRONT BODY PILLAR F

BODY PANEL  FRONT BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K105349

With the front body pillar lower gusset removed.


Weld work for 980 MPa ultra high strength steel

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

*1: When welding 2 panels together including 980 MPa ultra high strength steel.

Spot weld Pressure 2940 N (300 kgf, 661 lbf)
Weld current 10000 A
Weld time 18 Cyc. (0.30 Sec.)
Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas


*2: When welding more than 3 panels together including 980 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas


REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location


REMOVAL POINT
1.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


U147392E02
4.208,7.219 4.875,7.396 0.667,0.177 10 false 120 (4.72) 0.438,9.271 0.969,9.542 0.531,0.271 10 false mm (in.) 3.958,3.469 4.063,3.625 0.104,0.156 10 false 1 3.354,3.438 3.552,3.594 0.198,0.156 10 false 10 4.813,7.552 5.479,7.729 0.667,0.177 10 false 120 (4.72) 3.354,3.115 3.458,3.271 0.104,0.156 10 false 1 1.917,2.302 2.021,2.458 0.104,0.156 10 false 1 1.01,4.229 1.115,4.385 0.104,0.156 10 false 1 0.958,3.573 1.063,3.729 0.104,0.156 10 false 5 0.948,2.927 1.052,3.083 0.104,0.156 10 false 1 2.344,4.927 2.448,5.083 0.104,0.156 10 false 6 3.479,4.927 3.583,5.083 0.104,0.156 10 false 8

K139729

U147394E02
4.073,0.917 4.75,1.094 0.677,0.177 10 false 170 (6.69) 4.646,6.354 5.271,6.542 0.625,0.188 10 false 20 (0.79) 0.271,9.396 0.802,9.667 0.531,0.271 10 false mm (in.) 1.583,2.031 1.688,2.188 0.104,0.156 10 false 4 2.094,3.969 2.198,4.125 0.104,0.156 10 false 1 1.063,2.438 1.156,2.594 0.094,0.156 10 false 1 0.615,4.104 0.719,4.26 0.104,0.156 10 false 1 1.229,4.104 1.323,4.26 0.094,0.156 10 false 2 3.365,2.646 3.469,2.802 0.104,0.156 10 false 4 4.396,3.292 4.5,3.448 0.104,0.156 10 false 1 4.177,4.281 4.271,4.438 0.094,0.156 10 false 2 3.667,8.813 3.771,8.969 0.104,0.156 10 false 1 1.51,7.833 1.615,7.99 0.104,0.156 10 false 2 3.667,8.156 3.76,8.313 0.094,0.156 10 false 1 0.917,8.323 1.021,8.479 0.104,0.156 10 false 2 2.094,9.396 2.198,9.552 0.104,0.156 10 false 8 3.667,7.333 3.771,7.49 0.104,0.156 10 false 1 5.521,6.844 5.625,7 0.104,0.156 10 false 1

INSTALLATION


Symbol meaning
K108821

Spot Weld
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


5.

Follow the welding conditions when welding *1 and *2 to assure sufficient weld strength. (See the introduction)

6.

Before temporarily installing the new parts, weld the front body pillar sub-assembly inner and front pillar extension lower with the standard number of welding points.

7.

When welding *3, make a hole on a new part for plug welding and weld the panel with the panel behind completely.

8.

After welding the front body lower inner pillar the vehicle side, install the front body pillar sub-assembly inner and front pillar extension lower.

9.

After welding the front body lower inner pillar, front body pillar sub-assembly inner and front pillar extension lower the vehicle side, install the rocker reinforce sub-assembly outer.

10.

After welding the front body lower inner pillar, front body pillar sub-assembly inner, front pillar extension lower and rocker reinforce sub-assembly outer the vehicle side, install the front body pillar reinforce sub-assembly lower.

11.

After welding the front body lower inner pillar, front body pillar sub-assembly inner, front pillar extension lower, rocker reinforce sub-assembly outer and front body pillar reinforce sub-assembly lower the vehicle side, install the front body pillar upper outer and rocker panel outer rear.

12.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

13.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K139730E01
3.615,4.323 3.729,4.323 3.729,4.323 3.969,4.552 false 2.115,3.698 2.01,3.698 2.01,3.698 1.906,3.188 false 5.302,7.635 4.781,6.281 4.781,6.281 4.677,6.281 false 2.885,2.385 3.479,2.604 0.594,0.219 10 false 20 (0.79) 2.177,3.594 5.198,3.875 3.021,0.281 10 false FRONT BODY PILLAR SUB-ASSEMBLY INNER 1.219,4.219 3.552,4.458 2.333,0.24 10 false FRONT PILLAR EXTENSION LOWER 1.552,6.177 4.677,6.406 3.125,0.229 10 false ROCKER REINFORCE SUB-ASSEMBLY OUTER 2.531,8.698 3.26,8.958 0.729,0.26 10 false 440 (17.32) 0.521,9.271 1.083,9.49 0.563,0.219 10 false mm (in.)

K139731E01
3.385,5.5 3.552,5.5 3.552,5.5 4.583,7.094 false 6.094,7.906 6.406,8.104 0.313,0.198 10 false *3 0.583,2.906 0.896,3.104 0.313,0.198 10 false *3 0.917,5.396 3.375,5.635 2.458,0.24 10 false FRONT BODY LOWER INNER PILLAR

K139732E01
5.844,6.76 6.156,6.958 0.313,0.198 10 false *1 4.156,8.333 4.469,8.531 0.313,0.198 10 false *1 5.229,9.375 5.813,9.594 0.583,0.219 10 false 15 (0.59) 0.313,9.438 0.896,9.677 0.583,0.24 10 false mm (in.)

K139733E01
4.094,3.76 4.292,3.76 4.292,3.76 4.969,4.698 false 5.365,3.406 5.677,3.604 0.313,0.198 10 false *1 6.365,4.063 6.677,4.26 0.313,0.198 10 false *1 6.375,4.531 6.688,4.729 0.313,0.198 10 false *1 1.104,8.479 1.417,8.677 0.313,0.198 10 false *1 0.125,3.667 4.083,3.896 3.958,0.229 10 false FRONT BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER

K139734E01
4.969,6.75 4.844,6.75 4.844,6.75 4.521,5.76 false 4.344,3.594 3.833,3.229 3.833,3.229 3.719,3.229 false 1.219,3.125 3.729,3.354 2.51,0.229 10 false FRONT BODY PILLAR UPPER OUTER 5.031,6.646 7.083,6.875 2.052,0.229 10 false ROCKER PANEL OUTER REAR

K139735E01
1.938,1.198 2.25,1.396 0.313,0.198 10 false *2 3.531,2.552 3.844,2.75 0.313,0.198 10 false *2 5.281,5.823 5.854,6.052 0.573,0.229 10 false 5 (0.20) 0.25,9.51 0.833,9.74 0.583,0.229 10 false mm (in.)