Home › Vehicle Exterior › BODY PANEL › CENTER BODY PILLAR › from 2016.06
BM2090E _01 Vehicle Exterior _060720 BODY PANEL _0297851 CENTER BODY PILLAR F

BODY PANEL  CENTER BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K105350

With the quarter panel removed.


Weld work for 980 MPa ultra high strength steel

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

*1: When welding 2 panels together including 980 MPa ultra high strength steel.

Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas


*2: When welding more than 3 panels together including 980 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas


REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location


REMOVAL POINT
1.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)

2.

*3 is reused.


U190487E02
1.448,3.125 1.552,3.281 0.104,0.156 10 false 1 2.802,4.667 2.979,4.823 0.177,0.156 10 false 14 1.99,2.76 2.094,2.917 0.104,0.156 10 false 1 3.854,1.594 3.958,1.75 0.104,0.156 10 false 2 4.49,1.802 4.594,1.958 0.104,0.156 10 false 1 3.604,4.563 3.708,4.719 0.104,0.156 10 false 2 4.823,5.104 5,5.26 0.177,0.156 10 false 12 2.708,6.781 3.333,6.969 0.625,0.188 10 false 30 (1.18) 0.5,9.188 1.031,9.458 0.531,0.271 10 false mm (in.)

U147402E02
1.583,1.229 1.677,0.302 1.677,0.302 1.854,0.302 false 1.885,0.198 2.042,0.344 0.156,0.146 10 false *3 1.313,2.573 2,2.75 0.688,0.177 10 false 180 (7.09) 2.208,0.583 2.833,0.771 0.625,0.188 10 false 40 (1.57) 0.688,1.729 1.375,1.906 0.688,0.177 10 false 150 (5.91) 2.042,3.49 2.146,3.646 0.104,0.156 10 false 1 3.167,3.729 3.271,3.885 0.104,0.156 10 false 4 0.854,4.094 0.958,4.25 0.104,0.156 10 false 1 0.74,4.344 0.844,4.5 0.104,0.156 10 false 3 0.74,4.573 0.844,4.729 0.104,0.156 10 false 1 0.844,4.854 0.948,5.01 0.104,0.156 10 false 1 1.781,6.135 1.885,6.292 0.104,0.156 10 false 5 2.521,6.292 2.625,6.448 0.104,0.156 10 false 2 1.021,7.333 1.125,7.49 0.104,0.156 10 false 2 0.438,9.229 0.969,9.5 0.531,0.271 10 false mm (in.) 3.844,4.792 3.938,4.948 0.094,0.156 10 false 2 6.354,3.51 6.979,3.698 0.625,0.188 10 false 90 (3.54) 5.823,9.167 5.917,9.323 0.094,0.156 10 false 4

INSTALLATION


Symbol meaning
K108823

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Follow the welding conditions when welding *1 and *2 to assure sufficient weld strength. (See the introduction)

5.

Before temporarily installing the new parts, weld the center body pillar reinforcement sub-assembly and rocker reinforce sub-assembly outer with the standard number of welding points.

6.

After welding the No.1 inner pillar sub-assembly the vehicle side, install the center body pillar reinforcement sub-assembly and rocker reinforce sub-assembly outer.

7.

After welding the No.1 inner pillar sub-assembly, center body pillar reinforcement sub-assembly and rocker reinforce sub-assembly outer the vehicle side, install the *3.

8.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

9.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K139736E01
3.896,5.177 4.188,4.781 4.188,4.781 4.031,4.781 false 2.75,3.656 2.75,2.802 false 4.354,3.167 5.083,3.406 0.729,0.24 10 false 480 (18.90) 1.271,3.688 4.365,3.927 3.094,0.24 10 false ROCKER REINFORCE SUB-ASSEMBLY OUTER 0.125,4.667 4.021,4.885 3.896,0.219 10 false CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY 0.427,9.448 1.01,9.667 0.583,0.219 10 false mm (in.)

K139739E01
3.01,1.688 3.583,0.823 3.583,0.823 3.75,0.823 false 3.813,0.729 6.292,0.948 2.479,0.219 10 false NO.1 INNER PILLAR SUB-ASSEMBLY 4.125,6.854 4.729,7.094 0.604,0.24 10 false 20 (0.79) 2.302,8.906 2.885,9.156 0.583,0.25 10 false 15 (0.59) 0.156,9.573 0.74,9.781 0.583,0.208 10 false mm (in.)

K139740E01
1.75,8.146 2.125,7.135 2.125,7.135 2.271,7.135 false 3.49,0.563 3.802,0.76 0.313,0.198 10 false *1 1.552,1.365 1.865,1.563 0.313,0.198 10 false *1 1.719,4.542 2.031,4.74 0.313,0.198 10 false *1 2.448,4.677 2.76,4.875 0.313,0.198 10 false *1 3.177,5.708 3.49,5.906 0.313,0.198 10 false *1 0.604,5.49 0.917,5.688 0.313,0.198 10 false *1 0.615,5.938 0.927,6.135 0.313,0.198 10 false *1 2.073,7.521 2.385,7.719 0.313,0.198 10 false *2 2.313,7.031 2.625,7.229 0.313,0.198 10 false *3 0.771,8.802 1.083,9 0.313,0.198 10 false *2