Home › Vehicle Exterior › BODY PANEL › REAR FLOOR PAN
BM2090E _01 Vehicle Exterior _060720 BODY PANEL _0297857 REAR FLOOR PAN F

BODY PANEL  REAR FLOOR PAN  CUT AND JOIN REPLACEMENT SECTIONS  


K105096

With the body lower back panel removed.


REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108829

Cut Location


REMOVAL POINT
1.

After removing the rear floor side panel and rear bumper bracket, remove the rear floor pan.


K139757E01
0.885,4.219 0.719,4.219 0.719,4.219 1.229,2.896 false 2.146,2.365 3.74,2.854 3.74,2.854 3.875,2.854 false 0.208,0.156 0.552,0.406 0.344,0.25 12 false LH: 3.938,2.76 5.76,2.99 1.823,0.229 10 false REAR FLOOR SIDE PANEL 0.948,4.115 2.729,4.323 1.781,0.208 10 false REAR BUMPER BRACKET

K139758E01
2.885,2.323 3.719,1.625 3.719,1.625 3.875,1.625 false 3.156,2.708 3.552,3.115 3.552,3.115 3.677,3.115 false 0.229,0.167 0.583,0.406 0.354,0.24 12 false RH: 3.927,1.531 5.76,1.76 1.833,0.229 10 false REAR FLOOR SIDE PANEL 3.74,3.01 5.521,3.229 1.781,0.219 10 false REAR BUMPER BRACKET

U147377E03
3.385,6.063 3.385,6.615 3.385,6.615 3.594,6.615 false 3.604,4.979 4.177,5.167 0.573,0.188 10 true 30 (1.18) 2.938,4.896 3.531,5.104 0.594,0.208 10 true 30 (1.18) 1.865,6.406 1.969,6.563 0.104,0.156 10 false 5 5.448,6.406 5.552,6.563 0.104,0.156 10 false 5 0.229,9.417 0.76,9.688 0.531,0.271 10 false mm (in.) 3.646,6.531 5.042,6.771 1.396,0.24 10 false REAR FLOOR PAN

INSTALLATION


Symbol meaning
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108829

Cut Location
K108830

Fillet Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Cut the new part so that it overlaps the previous cut location.

2.

When welding *2, make a hole on a new part for plug welding and weld the panel with the panel behind completely.

3.

*1: Perform plug-welding in the area where the panel are overlapped. Apply body sealer to both sides of each panel.

HINT:
·

Confirm that the panels are securely welded together.

·

Apply body sealer in an even, continuous bead.



4.

After welding the rear floor pan to the vehicle side, install the rear floor side panel and rear bumper bracket.

5.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)

6.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K139759E01
3.823,3.625 3.698,3.625 3.698,3.625 3.583,3.156 false 4.938,1.969 5.656,2.229 0.719,0.26 10 false 130 (5.12) 4.958,2.542 5.698,2.75 0.74,0.208 10 false 290 (11.42) 3.885,2.094 4.5,2.333 0.615,0.24 10 true 20 (0.79) 2.698,2.083 3.313,2.323 0.615,0.24 10 true 20 (0.79) 1.573,1.958 2.292,2.219 0.719,0.26 10 false 130 (5.12) 1.573,2.531 2.313,2.74 0.74,0.208 10 false 290 (11.42) 3.896,3.521 5.177,3.729 1.281,0.208 10 false REAR FLOOR PAN 5.021,4.052 5.333,4.25 0.313,0.198 10 false *1 4.875,7.531 5.188,7.729 0.313,0.198 10 false *1 5.677,9.354 5.99,9.552 0.313,0.198 10 false *1 0.219,9.469 0.813,9.698 0.594,0.229 10 false mm (in.)

K139760E01
2.146,2.365 3.396,2.99 3.396,2.99 3.542,2.99 false 0.792,4.021 0.646,4.021 0.646,4.021 1.156,2.781 false 0.198,0.167 0.521,0.396 0.323,0.229 12 false LH: 1.865,0.792 2.094,0.99 0.229,0.198 10 false *2 3.26,2.26 3.49,2.458 0.229,0.198 10 false *2 3.625,2.896 5.438,3.125 1.813,0.229 10 false REAR FLOOR SIDE PANEL 0.865,3.927 2.646,4.125 1.781,0.198 10 false REAR BUMPER BRACKET

K139761E01
3.146,2.729 3.698,2.979 3.698,2.979 3.813,2.979 false 2.896,2.333 3.833,1.771 3.833,1.771 3.99,1.771 false 0.26,0.26 0.646,0.5 0.385,0.24 12 false RH: 1.927,0.719 2.24,0.917 0.313,0.198 10 false *2 4.042,1.688 5.865,1.917 1.823,0.229 10 false REAR FLOOR SIDE PANEL 3.875,2.875 5.667,3.104 1.792,0.229 10 false REAR BUMPER BRACKET 0.667,2.177 0.979,2.375 0.313,0.198 10 false *2