Home › Engine / Hybrid System › FA20 (INTAKE / EXHAUST) › EXHAUST SYSTEM › 2012.03–2016.06
NM2090E _51 Engine / Hybrid System _060623 FA20 INTAKE / EXHAUST _0297319 EXHAUST SYSTEM UN GENERAL/CONTROL/DETAILS F

FA20 INTAKE / EXHAUST  EXHAUST SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


CONSTRUCTION


a.

Exhaust Manifold Sub-assemblies

i.

Noise has been reduced and heat resistance has been ensured by the adoption of an insulator on the stainless steel exhaust manifold, while catalyst warm-up following engine startup has been quickened to lower emissions.


ii.

Loss of exhaust pressure has been reduced and power improved by the adoption of a 4-2-1 layout and optimization of the pipe diameter.


iii.

A catalytic converter that integrates with the exhaust manifold has been adopted, thereby quickening the catalytic converter warm-up and improving emission performance immediately after engine startup.


iv.

A design with compressed vertical dimensions has been adopted to lower the installation position of the engine.


v.

The intermediate pipe has been located above the front suspension crossmember to accommodate the low engine height.

W108178E03
3.792,0.875 3.281,0.563 true 1.344,3.177 2.625,2.417 true 3.833,3.698 3.375,4.167 true 3.49,1.885 5.229,1.781 5.229,1.781 5.094,3.219 true 3.094,0.438 3.25,0.615 0.156,0.177 10 false *1 1.177,3.115 1.333,3.292 0.156,0.177 10 false *2 3.229,4.156 3.385,4.333 0.156,0.177 10 false *3 5.24,1.625 5.396,1.802 0.156,0.177 10 false *4

Text in Illustration
*1 Intermediate Pipe *2 TWC
*3 Insulator *4 Exhaust Manifold



b.

Exhaust Pipe

i.

The exhaust pipes are made of stainless steel for improved rust resistance.


ii.

A compact sub-muffler has been installed to lower pressure loss and improve noise performance.


iii.

A low-pressure-loss catalyst has been installed to lower pressure loss and improve exhaust gas performance.


iv.

A ball joint is used to join the front exhaust pipe assembly and center exhaust pipe assembly. As a result, in-vehicle sound has been muffled, vibration has been minimized, and weight reduction has been achieved.

W107440E02
2.958,3.354 3.167,4.135 3.167,4.135 3.729,3.115 true 1.594,3.302 1.104,2.594 1.104,2.594 0.896,3.583 true 2.094,3.344 2.292,4.073 true 4.844,3.417 4.448,3.594 true 5.302,3.042 5.083,2.906 true 6.094,1.688 5.781,2.271 true 6.719,1.948 6.438,2.49 true 2.771,0.5 2.927,0.677 0.156,0.177 10 false *a 4.135,3.323 4.354,3.542 0.219,0.219 10 false *A 5.542,3.323 5.76,3.542 0.219,0.219 10 false *B 2.24,4.094 2.396,4.271 0.156,0.177 10 false *2 3.073,4.156 3.229,4.333 0.156,0.177 10 false *3 5.323,3.021 5.479,3.198 0.156,0.177 10 false *4 6.063,1.531 6.219,1.708 0.156,0.177 10 false *5 1.01,2.385 1.167,2.563 0.156,0.177 10 false *1 6.677,1.781 7.125,1.979 0.448,0.198 10 false *6 (*C) 4.865,3.323 5.073,3.521 0.208,0.198 10 false *6

Text in Illustration
*A Models for Korea *B Models for China
*C Models with Tail Pipe Baffle - -
*1 TWC *2 Front Exhaust Pipe Assembly
*3 Sub Muffler *4 Center Exhaust Pipe Assembly
*5 Tail Exhaust Pipe Assembly *6 Tail Pipe Baffle
*a Ball Joint Portion - -