Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM › 2012.03–2016.06
NM2090E _54 Brake _060637 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297335 BRAKE CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


Component Function
Combination Meter Assembly Brake System Warning Light
·

Illuminates to alert the driver when the skid control ECU detects a malfunction in the EBD or brake system.

·

Illuminates to alert the driver when the brake fluid level is low.

·

Illuminates to inform the driver of the parking brake condition.


ABS Warning Light Illuminates to alert the driver when the skid control ECU detects a malfunction in the ABS.
Slip Indicator Light
·

Blinks to inform the driver when the TRC and VSC.

·

Illuminates to alert the driver when the skid control ECU detects a malfunction in the TRC or VSC.


VSC OFF Indicator Light
·

Illuminates when the VSC OFF switch (pattern select switch assembly) is pressed for about three seconds to select VSC OFF Mode.*1

·

Illuminates when VSC SPORT Mode is selected.


VSC SPORT Indicator Light Illuminates when VSC SPORT Mode is selected.
TRC OFF Indicator Light
·

Illuminates when the VSC OFF switch (pattern select switch assembly) is pressed briefly to select TRC OFF Mode.*2

·

Illuminates when the VSC OFF switch (pattern select switch assembly) is pressed for about three seconds to select TRC OFF Mode.*1


VSC OFF Switch (Pattern Select Switch Assembly) Enables the driver to select "Normal Mode", "TRC OFF Mode", "VSC OFF Mode" or "VSC/TRC OFF Mode".
VSC SPORT Switch (Pattern Select Switch Assembly) Enables the driver to select Normal Mode or VSC SPORT Mode.
Stop Light Switch Assembly Detects the brake pedal depressing signal.
Steering Sensor Detects the direction and angle of the steering wheel.
Front and Rear Speed Sensors Detects the wheel speed of each of the 4 wheels.
Brake Actuator Assembly Changes the fluid path based on the signals from the skid control ECU during the operation of the brake control system functions, in order to control the fluid pressure applied to the wheel cylinders.
Master Cylinder Pressure Sensor
(Built into Brake Actuator Assembly)
Detects the master cylinder pressure.
Skid Control ECU Judges the vehicle driving condition based on the signals from each sensor, and sends the brake control signals to the brake actuator.
Yawrate Sensor
(with Built-in Skid Control ECU)
Detects vehicle turning angle velocity and front and rear, left and right acceleration.
ECM Based on the signals received from the skid control ECU, controls the engine output.

HINT:

*1: If the VSC OFF switch (pattern select switch assembly) is pressed for about three seconds, VSC and TRC turn off, and the VSC OFF indicator light and TRC OFF indicator light illuminate simultaneously.

*2: If the vehicle speed exceeds about 50 km/h (31.1 mph) while in TRC OFF mode, TRC automatically turns on, and the TRC OFF indicator light turns off.



SYSTEM CONTROL


Control Outline
Anti-lock Brake System (ABS) The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface.
Electronic Brake Force Distribution (EBD) The EBD control utilizes ABS, achieving proper brake force distribution between the front and rear wheels in accordance with the driving conditions.
Brake Assist
·

The primary purpose of brake assist is to provide an auxiliary brake force to assist a driver who cannot generate a large brake force during emergency braking, thus helping ensure the vehicle's braking performance.

·

If the skid control ECU judges that the brake pedal force applied by the driver is not sufficient to ensure adequate braking force, brake assist is used to enhance the braking force.


Traction Control (TRC) The TRC helps restrain the slippage of the drive wheels if the driver depresses the accelerator pedal excessively when starting off or while accelerating on a slippery surface.
Limited Slip Differential (LSD) Function The LSD function detects a difference in rotation speeds between the left and right drive wheels. If there is a difference in rotation speeds between them, this function applies brake to the drive wheel that rotates faster than the other using pressurization function of the VSC to minimize the difference.
Vehicle Stability Control (VSC) The VSC helps restrain sideways slippage of the vehicle during a strong front wheel skid or strong rear wheel skid, which may occur while cornering.

a.

Anti-lock Brake System (ABS)

i.

The ABS prevents the wheels from locking during sudden braking or braking on a slippery surface. This provides the proper braking force when the vehicle slips, thus ensuring vehicle stability and excellent braking performance.

X102923E04
1.448,2.198 1.823,2.573 0.375,0.375 12 false *B: 1.448,0.865 1.823,1.24 0.375,0.375 12 false *A: 4.573,0.927 4.823,1.167 0.25,0.24 10 false *a

Text in Illustration (Illustration Provides Conceptual Image:)
*A Models with ABS *B Models without ABS
*a Brake Operation - -



b.

Electronic Brake Force Distribution (EBD)

i.

This function controls the brake force that acts on the rear wheels in accordance with the changes in the vehicle conditions such as load factors or deceleration, in order to ensure excellent braking performance.

X100697E01
1.948,1.719 1.781,1.719 1.781,1.719 1.781,2.563 true 4.917,1.406 4.74,1.406 4.74,1.406 4.74,2.375 true 2.406,2.635 2.229,2.635 2.229,2.635 2.063,2.49 true 5.417,2.604 5.24,2.604 5.24,2.604 5.073,2.458 true 0.594,2.135 1.344,2.542 0.75,0.406 10 Rear Brake Force 3.583,2.135 4.344,2.781 0.76,0.646 10 Rear Brake Force 1.99,1.635 3.125,2.031 1.135,0.396 10 Ideal Brake Force Distribution 4.958,1.323 6.104,1.708 1.146,0.385 10 Ideal Brake Force Distribution 2.438,2.542 3.229,2.854 0.792,0.313 10 EBD Control 5.448,2.531 6.24,2.844 0.792,0.313 10 EBD Control 1.729,2.917 2.885,3.24 1.156,0.323 10 Front Brake Force 4.74,2.917 5.896,3.24 1.156,0.323 10 Front Brake Force 1.667,3.281 3.01,3.625 1.344,0.344 10 Without Load in Rear 4.781,3.292 5.927,3.625 1.146,0.333 10 With Load in Rear


ii.

During cornering braking, this function controls the brake force that acts on the left and right wheels in accordance with the vehicle conditions. This ensures vehicle stability and excellent braking performance.

X102924

Text in Illustration
V100136

Control Moment
V100135

Brake Force



c.

Brake Assist

i.

During the brake assist, the skid control ECU calculates the speed and the amount of the brake pedal application based on the signals from the master cylinder pressure sensor and then determines the intention of the driver to make an emergency brake application. If the skid control ECU determines that the driver intends to make an emergency brake application, this function activates the brake actuator to increase the brake fluid pressure, which increases the brake force.

X108794E02
0.854,2.948 3.979,3.323 3.125,0.375 10 false Fluid Pressure Increased by Brake Actuator 1.073,0.354 2.302,0.833 1.229,0.479 10 false Skid Control ECU 1.167,1.448 2.313,1.781 1.146,0.333 10 false Brake Actuator 3.938,0.823 4.406,1.677 0.469,0.854 10 false Brake Force 5.573,2.792 6.323,3.146 0.75,0.354 10 false Time 4.99,1.646 6.25,2.01 1.26,0.365 10 false With Brake Assist 4.771,2.323 6.313,2.646 1.542,0.323 10 false Without Brake Assist



d.

Traction Control (TRC)

i.

The TRC helps prevent the drive wheels from slipping if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface. Simultaneously with the hydraulic brake control of the drive wheels, the skid control ECU makes a request to the ECM to effect engine output control. This produces the drive force that suits the driving conditions, in order to ensure the proper start-off acceleration.

X102925E02
5.021,1.458 4.531,1.458 true 5.01,1.052 4.521,1.052 true 6.115,1.896 5.458,1.896 true 4.354,1.354 4.552,1.604 0.198,0.25 10 false *2 2.563,0.313 2.844,0.615 0.281,0.302 12 false *B: 0.948,0.313 1.229,0.604 0.281,0.292 12 false *A: 4.344,0.948 4.521,1.177 0.177,0.229 10 false *1 6.146,1.792 6.365,2.052 0.219,0.26 10 false *a

Text in Illustration (Driving on Road with Differing Surface Friction Characteristics:)
*A Models without TRC *B Models with TRC
*1 ECM
- Engine Output Control
*2 Brake Actuator Assembly
- Hydraulic Brake Control
*a Brake Slipping Drive Wheel - -
V100145

Slippery Surface - -



e.

Limited Slip Differential (LSD) Function

i.

The LSD function detects a difference in rotation speeds between the left and right drive wheels. If there is a difference in rotation speeds between them, this function applies brake to the drive wheel that rotates faster than the other using pressurization function of the VSC* to minimize the difference.


ii.

This function makes it possible to start and accelerate the vehicle stably.

HINT:

*:This function always activates regardless of ON/OFF of the VSC mode.




f.

Vehicle Stability Control (VSC)

i.

The following are 2 examples that can be considered circumstances in which the tires exceed their lateral grip limit. The VSC is designed to help control the vehicle behavior by controlling the engine output and the brakes of each wheel when the vehicle is under one of the conditions indicated below:

X102948E01
4.696,2.1 5.333,2.377 0.638,0.277 10 *b 2.154,2.1 2.792,2.377 0.638,0.277 10 *a

Text in Illustration
*a Front Wheel Skid Tendency (Understeer)
- When the front wheels lose grip in relation to the rear wheel
*b Rear Wheel Skid Tendency (Oversteer)
- When the rear wheels lose grip in relation to the front wheels


ii.

The vehicle's sideways skid tendency is determined by the skid control computer based on the target yaw rate and actual vehicle yaw rate values.


iii.

Whether or not the vehicle is experiencing a front wheel skid is determined by the difference between the target yaw rate and the vehicle's actual yaw rate. When the vehicle's actual yaw rate is smaller than the target yaw rate (which is determined based on the vehicle speed and steering angle) that should be generated when the driver operates the steering wheel, it means the vehicle is making a turn at a greater angle than the target locus of travel. Thus, the skid control ECU determines that there is a large front wheel skid tendency.

X102926E01
3.366,0.042 3.752,0.288 0.386,0.247 10 *a 4.744,0.75 5.129,0.996 0.386,0.247 10 *b

Text in Illustration
*a Actual Locus of Travel (Actual Yaw Rate) *b Locus of Travel Based on Target Yaw Rate


iv.

Whether or not the vehicle is experiencing a rear wheel skid is determined by the values of the vehicle's slip angle and the vehicle's slip angular velocity (time-dependent changes in the vehicle's slip angle). When the vehicle's slip angle is large, and the slip angular velocity is also large, the skid control ECU determines that the vehicle has a large rear wheel skid tendency.

X102927E01
3.566,0.029 3.852,0.287 0.286,0.258 10 *a 3.902,0.174 4.188,0.432 0.286,0.258 10 *b

Text in Illustration
*a Travel Direction of Vehicle's Center of Gravity *b Movement of Vehicle
V100136

Slip Angle - -


v.

When the skid control ECU determines that the vehicle is exhibiting a tendency to experience a front wheel skid or a rear wheel skid, it decreases the engine output and applies the brakes of each wheel to control the vehicle's yaw moment. The basic operation of the VSC is described below. However, the control method differs depending on the vehicle's characteristics and driving conditions.


vi.

When the skid control ECU determines that there is a front wheel skid tendency, it applies the brake on the rear wheel on the inside of the turn in accordance with the extent of the skid tendency in order to help restrain the front wheel from skidding.

X108795

Text in Illustration
V100136

Control Moment
V100135

Brake Force


vii.

When the skid control ECU determines that there is a large rear wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. It applies the brakes of the front wheel of the outer circle of the turn, and generates an outward moment of inertia in the vehicle, in order to restrain the rear wheel skid tendency. Along with the reduction in the vehicle speed caused by the braking force, excellent vehicle stability is ensured. In some cases, the skid control ECU applies the brake of the rear wheels, as necessary.

X108796

Text in Illustration
V100136

Control Moment
V100135

Brake Force




FUNCTION


a.

VSC OFF Switch (Pattern Select Switch Assembly)

i.

The operation of the VSC and TRC functions can be stopped by the VSC OFF switch (pattern select switch assembly). While the vehicle is running off the shoulder of the road or running on a dirt road, the engine output control is stopped to maintain drive torque.

X108406E02
5.531,1.979 5.531,2.323 true 1.667,0.646 1.875,0.854 0.208,0.208 10 false *2 1.146,0.656 1.354,0.865 0.208,0.208 10 false *1 5.458,2.344 5.667,2.552 0.208,0.208 10 false *3

Text in Illustration
*1 VSC OFF Indicator Light *2 TRC OFF Indicator Light
*3 VSC OFF Switch (Pattern Select Switch Assembly) - -


ii.

The VSC OFF switch (pattern select switch assembly) can select 3 modes (Normal mode, TRC OFF mode, and VSC OFF mode).


iii.

Briefly pressing the VSC OFF switch (pattern select switch assembly) in Normal mode selects TRC OFF mode.


iv.

Pressing and holding the VSC OFF switch (pattern select switch assembly) for 3 seconds or more will disable the VSC and TRC functions.


v.

Briefly pressing the VSC OFF switch (pattern select switch assembly) in TRC OFF mode or VSC OFF mode or turning the ignition switch off returns to the Normal mode.

X102940E06
3.51,0.552 3.854,0.844 0.344,0.292 10 false *a 4.875,1.781 5.219,2.073 0.344,0.292 10 false *b 2.094,1.792 2.438,2.083 0.344,0.292 10 false *c

Text in Illustration
*a Normal Mode *b TRC OFF Mode
*c VSC OFF Mode and TRC OFF Mode - -
V100135

VSC OFF Switch (Pattern Select Switch Assembly) Operation (Press and Hold for 3 Seconds or More)
V100136

VSC OFF Switch (Pattern Select Switch Assembly) Operation (Brief)


vi.

The operations of the brake control functions in each mode are as follows:

Mode Brake Control Function Combination Meter Assembly
TRC VSC Slip Indicator Light TRC OFF Indicator Light VSC OFF Indicator Light
Normal Mode Controllable Controllable - - -
TRC OFF Mode Not Controllable Controllable - (Blinks)*1 Illuminates -
VSC/TRC OFF Mode Not Controllable Not Controllable*2 - Illuminates Illuminates

HINT:

*1: When VSC is active

*2: If there is a major variance between the left and right driving wheels, the brakes might be applied.




b.

VSC SPORT Switch (Pattern Select Switch Assembly)

i.

Use this VSC SPORT switch (pattern select switch assembly) to allow the skid control computer to switch VSC control between Normal Mode and SPORT Mode.


ii.

Press the VSC SPORT switch (pattern select switch assembly) to switch VSC to SPORT Mode. When this happens, the driver will be informed that the vehicle is in VSC SPORT Mode by the illumination of the VSC SPORT indicator light and VSC OFF indicator light in the combination meter assembly.


iii.

In VSC SPORT mode, the VSC function is set to operate at a timing suitable for sporty driving, and only brake control is performed (engine output control is not performed).

X108407E03
6.521,1.938 6.521,2.281 true 0.948,0.656 1.156,0.865 0.208,0.208 10 false *1 6.448,2.292 6.719,2.5 0.271,0.208 10 false *2

Text in Illustration
*1 VSC SPORT Indicator Light *2 VSC SPORT Switch (Pattern Select Switch Assembly)




CONSTRUCTION


a.

Steering Sensor

i.

The steering sensor detects the steering direction and angle, and sends this information to the skid control ECU.

X108408E03
3.552,2.031 4.219,2.396 4.219,2.396 3.313,2.115 true 3.625,1.74 4.833,1.26 true 4.26,2.344 4.5,2.594 0.24,0.25 10 false *2 4.854,1.146 5.063,1.375 0.208,0.229 10 false *1 2.052,0.396 2.26,0.615 0.208,0.219 10 false *a

Text in Illustration
*1 Steering Sensor *2 Detection Gear
*a Front - -



b.

Speed Sensor

i.

An active type speed sensor is used. This sensor contains a Hall IC.


ii.

The sensor rotor, which consists of N and S poles that are arranged in a circle, is integrated with the hub bearing inner race.


iii.

An active type speed sensor uses a Hall IC to detect magnetic field changes caused when the sensor rotor rotates, and the sensor outputs the detected information to the skid control ECU as digital pulses.


iv.

To detect the vehicle speed, the frequency of the output pulses is used. Because the active sensor outputs vehicle speed pulses, the speed of the vehicle can be detected at speeds of 1.35 km/h (0.84 mph) or higher.

X100718E18
5.177,3.177 5.344,2.99 5.344,2.99 5.604,2.99 true 4.333,6.792 4.5,6.604 4.5,6.604 4.76,6.604 false 1.969,2.094 3.073,2.427 1.104,0.333 10 false Sensor Rotor 4,1.281 4.573,1.635 0.573,0.354 10 false Hall IC 5.656,2.896 6.76,3.229 1.104,0.333 10 false Speed Sensor 1.625,4.375 3.385,4.719 1.76,0.344 10 false N and S Poles Arrangement 2.135,5.479 2.646,5.958 0.51,0.479 10 false Vehicle Speed 2.135,6.542 2.646,7.021 0.51,0.479 10 false Sensor Output 4.833,6.51 5.938,6.844 1.104,0.333 10 false Digital Pulses 3.469,7.292 3.854,7.594 0.385,0.302 10 false Time



c.

Brake Actuator Assembly

i.

The brake actuator assembly consists of the brake actuator portion and skid control ECU.

X108410E02
3.521,0.531 4.521,0.219 4.521,0.219 4.667,0.219 true 3.281,0.583 2.688,0.24 2.688,0.24 2.542,0.24 true 2.906,0.958 2.302,0.677 2.302,0.677 2.125,0.677 true 3.865,0.698 4.823,1.052 4.823,1.052 4.969,1.052 true 4.135,1.615 4.875,1.938 4.875,1.938 5.021,1.938 true 3.99,1.802 4.75,2.531 4.75,2.531 4.927,2.531 true 2.156,2.042 1.677,1.823 1.677,1.823 1.51,1.823 true 3.875,2.313 4.188,2.594 4.188,2.594 4.365,2.594 true 2.365,0.125 2.542,0.365 0.177,0.24 10 false *4 1.948,0.573 2.135,0.792 0.188,0.219 10 false *3 1.333,1.719 1.521,1.958 0.188,0.24 10 false *2 4.708,0.125 4.969,0.354 0.26,0.229 10 false *5 5,0.938 5.219,1.167 0.219,0.229 10 false *6 5.063,1.833 5.281,2.104 0.219,0.271 10 false *7 4.969,2.417 5.188,2.646 0.219,0.229 10 false *8 4.396,2.479 4.594,2.698 0.198,0.219 10 false *1

Text in Illustration
*1 Brake Actuator Portion *2 Skid Control ECU
*3 Right Rear Brake Pipe *4 Left Front Brake Pipe
*5 Right Front Brake Pipe *6 Left Rear Brake Pipe
*7 Master Cylinder Pipe (Primary Side) *8 Master Cylinder Pipe (Secondary Side)


ii.

The actuator portion consists of 2 master cylinder cut solenoid valves, 2 reservoir cut solenoid valves, 4 pressure holding solenoid valves, 4 pressure reduction solenoid valves, 2 pumps, 2 reservoirs, and a master cylinder pressure sensor.

X108411E02
3.323,0.74 2.906,0.24 2.906,0.24 2.781,0.24 true 3.26,4.969 3.385,5.156 3.385,5.156 3.385,5.625 true 3.958,4.969 3.833,5.156 3.833,5.156 3.833,5.625 true 3.208,6.583 3.208,7 true 4,6.583 4,7 true 5.625,1.635 5.427,1.635 true 2.615,0.125 2.781,0.344 0.167,0.219 10 false *1 0.948,2.958 1.177,3.198 0.229,0.24 10 false *4 0.146,1.365 0.344,1.583 0.198,0.219 10 false *2 1.938,2.958 2.177,3.188 0.24,0.229 10 false *5 1.198,4.552 1.448,4.771 0.25,0.219 10 false *6 2.375,4.552 2.635,4.76 0.26,0.208 10 false *6 1.198,5.792 1.438,6.031 0.24,0.24 10 false *7 2.375,5.792 2.625,6.031 0.25,0.24 10 false *7 1.198,7.385 1.531,7.604 0.333,0.219 10 false *10 2.385,7.385 2.719,7.604 0.333,0.219 10 false *11 4.667,7.396 4.969,7.625 0.302,0.229 10 false *12 5.875,7.396 6.198,7.646 0.323,0.25 10 false *13 3.146,7 3.375,7.229 0.229,0.229 10 false *9 3.948,7 4.177,7.229 0.229,0.229 10 false *9 3.74,5.625 3.938,5.844 0.198,0.219 10 false *8 3.323,5.625 3.573,5.854 0.25,0.229 10 false *8 4.708,4.552 4.948,4.771 0.24,0.219 10 false *6 5.865,4.552 6.094,4.76 0.229,0.208 10 false *6 4.708,5.781 5,6.01 0.292,0.229 10 false *7 5.865,5.781 6.146,6.031 0.281,0.25 10 false *7 5.25,1.531 5.438,1.75 0.188,0.219 10 false *3 5.146,2.958 5.396,3.198 0.25,0.24 10 false *5 6.115,2.958 6.365,3.208 0.25,0.25 10 false *4

Text in Illustration
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Master Cylinder Cut Solenoid Valve
*5 Reservoir Cut Solenoid Valve *6 Pressure Holding Solenoid Valve
*7 Pressure Reduction Solenoid Valve *8 Pump
*9 Reservoir *10 Rear Brake Caliper (Right Side)
*11 Front Brake Caliper (Left Side) *12 Front Brake Caliper (Right Side)
*13 Rear Brake Caliper (Left Side) - -




OPERATION


a.

ABS and EBD

i.

Based on the signals received from the 4 speed sensors, the skid control ECU calculates the speed of each wheel, and checks the wheel slipping conditions. In accordance with the slipping condition, the skid control ECU controls each solenoid valve in the brake actuator in order to adjust the fluid pressure of each wheel cylinder in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes.

X102082E03
2.906,2.802 3.583,2.521 true 2.938,0.719 3.594,0.958 true 6.333,3.375 6.677,3.677 0.344,0.302 10 false *e 5.792,0.188 6.104,0.427 0.313,0.24 10 false *c 3.5,0.156 3.844,0.438 0.344,0.281 10 false *b 2.688,2.76 2.948,3.042 0.26,0.281 10 false *4 1.219,3.229 1.563,3.531 0.344,0.302 10 false *2 1.219,1.646 1.563,1.948 0.344,0.302 10 false *1 2.76,0.583 3.104,0.885 0.344,0.302 10 false *3 1.271,0.146 1.594,0.417 0.323,0.271 10 false *a 1.781,3.396 2.125,3.698 0.344,0.302 10 false *d

Text in Illustration
*1 Pressure Holding Solenoid Valve *2 Pressure Reduction Solenoid Valve
*3 Port A *4 Port B
*a Pressure Increase Mode *b Pressure Holding Mode
*c Pressure Reduction Mode *d to Wheel Cylinder
*e from Wheel Cylinder - -

Brake Actuator Operation in ABS and EBD
Pressure Mode Increase Mode Holding Mode Reduction Mode
Pressure Holding Solenoid Valve (Port A) Off (Open) On (Closed) On (Closed)
Pressure Reduction Solenoid Valve (Port B) Off (Closed) Off (Closed) On (Open)
Wheel Cylinder Pressure Increases Holds Reduces



b.

Brake Assist

i.

In the event of emergency braking, the skid control ECU determines the driver's intention based on the speed of the pressure increase in the master cylinder determined by the master cylinder pressure sensor signal. If the skid control ECU judges the need for additional brake assist, pressure is generated by the pump in the brake actuator and directed to the wheel cylinder to apply a large amount of fluid pressure.

X108412E02
0.656,1.135 2.135,1.479 1.479,0.344 10 false Speed Sensor (4) 0.313,3.729 2.26,4.073 1.948,0.344 10 false Stop Light Switch Assembly 3.125,0.573 4.125,0.958 1,0.385 10 false Solenoid Relay 3.063,2.063 4.292,2.719 1.229,0.656 10 false Skid Control ECU 3.198,3.625 4.073,3.979 0.875,0.354 10 false Motor Relay 3.281,2.979 4.052,3.323 0.771,0.344 10 false G Sensor 3.083,4.24 4.125,4.573 1.042,0.333 10 false Yawrate Sensor 5.281,0.417 6.667,1.104 1.385,0.688 10 false Master Cylinder Cut Solenoid Valve (2) 5.198,1.229 6.729,1.896 1.531,0.667 10 false Reservoir Cut Solenoid Valve (2) 5.021,2.031 6.802,2.698 1.781,0.667 10 false Pressure Holding Solenoid Valve (4) 5,2.844 6.802,3.51 1.802,0.667 10 false Pressure Reduction Solenoid Valve (4) 5.521,3.635 6.563,3.969 1.042,0.333 10 false Pump Motor 5.115,4.125 6.75,4.792 1.635,0.667 10 false Master Cylinder Pressure Sensor 2.708,5.323 4.625,5.667 1.917,0.344 10 false Combination Meter Assembly 5.406,4.969 7.073,5.438 1.667,0.469 10 false Brake Actuator Assembly 3,5.802 4.469,6.146 1.469,0.344 10 false Brake Warning Light 3.042,6.208 4.469,6.563 1.427,0.354 10 false ABS Warning Light 3.719,4.948 4.76,5.271 1.042,0.323 10 false CAN (V Bus)

X108413E02
3.156,0.635 2.781,0.24 2.781,0.24 2.604,0.24 true 1,2.281 0.76,1.969 0.76,1.969 0.615,1.969 true 2.021,2.281 2.531,1.969 2.531,1.969 2.677,1.969 true 5.188,2.281 4.635,1.958 4.635,1.958 4.49,1.958 true 6.208,2.292 6.479,1.927 6.479,1.927 6.625,1.927 true 5.948,5.156 6.479,4.781 6.479,4.781 6.615,4.781 true 5.927,3.927 5.521,4.344 5.521,4.344 5.406,4.344 true 4.781,3.917 5.167,3.74 5.167,3.74 5.26,3.74 true 2.427,3.927 2.021,4.344 2.021,4.344 1.896,4.344 true 1.292,3.927 1.677,3.75 1.677,3.75 1.771,3.75 true 4.792,5.167 5,4.958 5,4.958 5.083,4.958 true 1.26,5.177 0.729,4.802 0.729,4.802 0.583,4.802 true 2.417,5.167 2.219,4.969 2.219,4.969 2.115,4.969 true 3.281,4.896 3.396,5.01 3.396,5.01 3.396,5.573 true 3.948,4.906 3.823,5.021 3.823,5.021 3.823,5.583 true 3.208,6.521 3.208,6.99 true 4,6.531 4,7 true 5.625,1.594 5.417,1.594 true 5.24,1.479 5.427,1.708 0.188,0.229 10 false *3 2.438,0.135 2.604,0.365 0.167,0.229 10 false *1 0.146,1.365 0.354,1.635 0.208,0.271 10 false *2 0.938,2.896 1.229,3.198 0.292,0.302 10 false (1) 1.906,2.896 2.208,3.156 0.302,0.26 10 false (2) 1.177,4.5 1.479,4.75 0.302,0.25 10 false (5) 2.354,4.49 2.667,4.719 0.313,0.229 10 false (6) 1.208,5.729 1.448,6.063 0.24,0.333 10 false (9) 2.323,5.729 2.625,6.01 0.302,0.281 10 false (10) 0.406,1.865 0.667,2.156 0.26,0.292 10 false (A) 2.719,1.875 3.01,2.177 0.292,0.302 10 false (B) 5.125,2.896 5.365,3.167 0.24,0.271 10 false (3) 6.125,2.896 6.438,3.167 0.313,0.271 10 false (4) 4.708,4.5 5.01,4.74 0.302,0.24 10 false (7) 5.865,4.5 6.167,4.76 0.302,0.26 10 false (8) 4.667,5.729 4.99,6.01 0.323,0.281 10 false (11) 5.823,5.729 6.146,6.052 0.323,0.323 10 false (12) 4.708,7.333 4.958,7.604 0.25,0.271 10 false *8 3.146,6.99 3.365,7.24 0.219,0.25 10 false *5 3.948,7 4.167,7.219 0.219,0.219 10 false *5 3.75,5.573 3.958,5.802 0.208,0.229 10 false *4 3.344,5.573 3.542,5.823 0.198,0.25 10 false *4 5.885,7.344 6.156,7.594 0.271,0.25 10 false *9 1.177,7.333 1.448,7.573 0.271,0.24 10 false *6 2.375,7.333 2.594,7.604 0.219,0.271 10 false *7 4.271,1.854 4.521,2.135 0.25,0.281 10 false (C) 6.667,1.823 6.927,2.083 0.26,0.26 10 false (D) 6.667,4.667 6.927,4.948 0.26,0.281 10 false (L) 5.188,4.229 5.427,4.5 0.24,0.271 10 false (H) 5.302,3.646 5.563,3.927 0.26,0.281 10 false (G) 1.688,4.229 1.927,4.531 0.24,0.302 10 false (F) 1.802,3.646 2.063,3.927 0.26,0.281 10 false (E) 5.125,4.865 5.365,5.146 0.24,0.281 10 false (K) 1.948,4.875 2.198,5.156 0.25,0.281 10 false (J) 0.427,4.698 0.656,4.99 0.229,0.292 10 false (I)

Text in Illustration (Brake Assist Operation:)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Rear Brake Caliper (Right Side)
*7 Front Brake Caliper (Left Side) *8 Front Brake Caliper (Right Side)
*9 Rear Brake Caliper (Left Side) - -


ii.

Each valve operates as shown below:

Item Port Brake Assist Not Activated Brake Assist Activated
Master Cylinder Cut Solenoid Valves (1), (4) (A), (D) OFF (Open) ON*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open)
Front Brakes Pressure Holding Solenoid Valves (6), (7) (F), (G) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valves (10), (11) (J), (K) OFF (Closed) OFF (Closed)
Rear Brakes Pressure Holding Solenoid Valves (5), (8) (E), (H) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valves (9), (12) (I), (L) OFF (Closed) OFF (Closed)
Pump OFF ON

HINT:

*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.




c.

TRC

i.

The fluid pressure generated by the pump is regulated by the master cylinder cut solenoid valve to the required pressure. Thus, the wheel cylinders of the drive wheels are controlled in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes to control the slippage of the drive wheels.

X108416E03
0.677,1.635 2.094,1.99 1.417,0.354 10 false Speed Sensor (4) 3.104,1.063 4.146,1.427 1.042,0.365 10 false Solenoid Relay 3.083,2.833 4.323,3.271 1.24,0.438 10 false Skid Control ECU 3.219,4.135 4.135,4.49 0.917,0.354 10 false Motor Relay 5.229,0.917 6.771,1.594 1.542,0.677 10 false Master Cylinder Cut Solenoid Valve (2) 5.135,1.719 6.615,2.406 1.479,0.688 10 false Reservoir Cut Solenoid Valve (2) 5,2.531 6.771,3.198 1.771,0.667 10 false Pressure Holding Solenoid Valve (4) 5,3.323 6.823,4.01 1.823,0.688 10 false Pressure Reduction Solenoid Valve (4) 5.51,4.135 6.615,4.49 1.104,0.354 10 false Pump Motor 5.115,4.625 6.719,5.292 1.604,0.667 10 false Master Cylinder Pressure Sensor 5.375,5.458 7.115,5.802 1.74,0.344 10 false Brake Actuator Assembly 3.323,3.51 4.094,3.875 0.771,0.365 10 false G Sensor 3.104,4.771 4.135,5.125 1.031,0.354 10 false Yawrate Sensor 0.323,7.573 2.052,8.24 1.729,0.667 10 false Transmission Control ECU Assembly 1.021,6.531 1.531,6.865 0.51,0.333 10 false ECM 3.698,7.76 4.677,8.219 0.979,0.458 10 false CAN (V Bus) 5.042,5.854 7,6.198 1.958,0.344 10 false Combination Meter Assembly 5.302,6.365 6.792,6.698 1.49,0.333 10 false Brake Warning Light 5.354,6.76 6.698,7.115 1.344,0.354 10 false ABS Warning Light 5.323,7.958 6.719,8.302 1.396,0.344 10 false Slip Indicator Light 5.177,7.552 6.833,7.906 1.656,0.354 10 false VSC OFF Indicator Light 5.156,7.156 6.823,7.51 1.667,0.354 10 false TRAC OFF Indicator Light 0.552,4.208 2.063,4.573 1.51,0.365 10 false VSC SPORT Switch 0.656,4.729 1.969,5.083 1.313,0.354 10 false VSC OFF Switch 0.531,3.698 2.135,4.042 1.604,0.344 10 false Pattern Select Switch 5.083,8.354 6.865,8.698 1.781,0.344 10 false VSC SPORT Indicator Light

X108417E02
3.104,0.698 2.74,0.302 2.74,0.302 2.563,0.302 true 0.948,2.344 0.708,2.031 0.708,2.031 0.563,2.031 true 1.969,2.344 2.479,2.021 2.479,2.021 2.615,2.021 true 5.135,2.333 4.583,2.01 4.583,2.01 4.448,2.01 true 6.156,2.344 6.427,1.969 6.427,1.969 6.563,1.969 true 5.885,5.219 6.417,4.844 6.417,4.844 6.563,4.844 true 5.875,3.969 5.469,4.375 5.469,4.375 5.344,4.375 true 4.729,3.979 5.115,3.802 5.115,3.802 5.208,3.802 true 2.365,3.969 1.969,4.375 1.969,4.375 1.844,4.375 true 1.24,3.969 1.625,3.792 1.625,3.792 1.708,3.792 true 4.74,5.219 4.938,5.021 4.938,5.021 5.031,5.021 true 1.219,5.198 0.688,4.823 0.688,4.823 0.542,4.823 true 2.365,5.208 2.167,5.01 2.167,5.01 2.073,5.01 true 3.208,4.958 3.333,5.063 3.333,5.063 3.333,5.635 true 3.885,4.969 3.771,5.073 3.771,5.073 3.771,5.646 true 3.156,6.563 3.156,7.042 true 3.948,6.563 3.948,7.042 true 5.573,1.635 5.354,1.635 true 5.177,1.521 5.354,1.729 0.177,0.208 10 false *3 2.385,0.198 2.563,0.417 0.177,0.219 10 false *1 0.094,1.385 0.323,1.656 0.229,0.271 10 false *2 0.885,2.948 1.146,3.219 0.26,0.271 10 false (1) 1.865,2.948 2.094,3.208 0.229,0.26 10 false (2) 1.125,4.552 1.427,4.792 0.302,0.24 10 false (5) 2.292,4.552 2.583,4.792 0.292,0.24 10 false (6) 1.167,5.792 1.469,6.042 0.302,0.25 10 false (9) 2.271,5.792 2.594,6.042 0.323,0.25 10 false (10) 0.354,1.927 0.615,2.198 0.26,0.271 10 false (A) 2.656,1.917 2.958,2.167 0.302,0.25 10 false (B) 5.063,2.948 5.365,3.208 0.302,0.26 10 false (3) 6.073,2.958 6.365,3.219 0.292,0.26 10 false (4) 4.656,4.552 4.917,4.813 0.26,0.26 10 false (7) 5.802,4.552 6.052,4.802 0.25,0.25 10 false (8) 4.615,5.781 4.969,6.042 0.354,0.26 10 false (11) 5.76,5.781 6.073,6.021 0.313,0.24 10 false (12) 4.635,7.385 4.885,7.667 0.25,0.281 10 false *8 3.115,7.042 3.344,7.271 0.229,0.229 10 false *5 3.896,7.031 4.125,7.25 0.229,0.219 10 false *5 3.698,5.646 3.927,5.906 0.229,0.26 10 false *4 3.281,5.625 3.51,5.865 0.229,0.24 10 false *4 5.833,7.385 6.104,7.656 0.271,0.271 10 false *9 1.115,7.385 1.375,7.635 0.26,0.25 10 false *6 2.302,7.385 2.552,7.656 0.25,0.271 10 false *7 4.219,1.906 4.458,2.156 0.24,0.25 10 false (C) 6.604,1.865 6.854,2.125 0.25,0.26 10 false (D) 6.604,4.74 6.854,5.01 0.25,0.271 10 false (L) 5.125,4.26 5.354,4.531 0.229,0.271 10 false (H) 5.25,3.708 5.51,3.979 0.26,0.271 10 false (G) 1.625,4.229 1.865,4.5 0.24,0.271 10 false (F) 1.75,3.708 2.031,3.948 0.281,0.24 10 false (E) 5.073,4.917 5.333,5.188 0.26,0.271 10 false (K) 1.896,4.917 2.146,5.198 0.25,0.281 10 false (J) 0.385,4.719 0.594,4.99 0.208,0.271 10 false (I)

Text in Illustration (TRC Operation:)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Rear Brake Caliper (Right Side)
*7 Front Brake Caliper (Left Side) *8 Front Brake Caliper (Right Side)
*9 Rear Brake Caliper (Left Side) - -


ii.

Each valve operates as shown below:

Item Port TRC Not Activated TRC Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON* ON* ON*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open) ON (Open) ON (Open)
Front Brakes Pressure Holding Solenoid Valve (6), (7) (F), (G) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (10), (11) (J), (K) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure - - - - - -
Rear Brakes Pressure Holding Solenoid Valve (5), (8) (E), (H) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (9), (12) (I), (L) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Brake Wheel Cylinder Pressure - - - Increased Held Reduced
Pump OFF ON ON ON

HINT:

*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.




d.

VSC

i.

The VSC, by way of solenoid valves, controls the fluid pressure generated by the pump and applies it to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes. As a result, the tendency to front wheel skid or rear wheel skid is controlled.

X108418E04
0.677,1.417 2,1.76 1.323,0.344 10 false Speed Sensor (4) 3.146,0.844 4.167,1.208 1.021,0.365 10 false Solenoid Relay 3.073,2.625 4.323,3.115 1.25,0.49 10 false Skid Control ECU 3.24,3.927 4.125,4.281 0.885,0.354 10 false Motor Relay 5.292,0.688 6.656,1.375 1.365,0.688 10 false Master Cylinder Cut Solenoid Valve (2) 5.198,1.51 6.677,2.177 1.479,0.667 10 false Reservoir Cut Solenoid Valve (2) 5.052,2.313 6.75,2.979 1.698,0.667 10 false Pressure Holding Solenoid Valve (4) 5.021,3.125 6.833,3.792 1.813,0.667 10 false Pressure Reduction Solenoid Valve (4) 5.521,3.927 6.542,4.25 1.021,0.323 10 false Pump Motor 5.156,4.406 6.771,5.073 1.615,0.667 10 false Master Cylinder Pressure Sensor 3.135,4.583 4.177,4.948 1.042,0.365 10 false Yawrate Sensor 0.719,5.615 2.094,5.969 1.375,0.354 10 false Steering Sensor 5.063,5.646 7,5.958 1.938,0.313 10 false Combination Meter Assembly 5.271,5.24 7.042,5.594 1.771,0.354 10 false Brake Actuator Assembly 5.323,6.156 6.813,6.49 1.49,0.333 10 false Brake Warning Light 5.375,6.542 6.75,6.885 1.375,0.344 10 false ABS Warning Light 5.354,7.74 6.781,8.083 1.427,0.344 10 false Slip Indicator Light 5.198,7.344 6.833,7.688 1.635,0.344 10 false VSC OFF Indicator Light 5.177,6.948 6.854,7.302 1.677,0.354 10 false TRC OFF Indicator Light 3.313,3.302 4.083,3.667 0.771,0.365 10 false G Sensor 0.573,4 2.073,4.333 1.5,0.333 10 false VSC SPORT Switch 0.604,4.51 1.917,4.865 1.313,0.354 10 false VSC OFF Switch 0.479,3.49 2.083,3.833 1.604,0.344 10 false Pattern Select Switch 5.104,8.135 6.885,8.469 1.781,0.333 10 false VSC SPORT Indicator Light 3.708,8.083 4.708,8.521 1,0.438 10 false CAN (V Bus) 0.385,7.906 2.125,8.563 1.74,0.656 10 false Transmission Control ECU Assembly 1.104,6.885 1.698,7.229 0.594,0.344 10 false ECM


ii.

During front wheel skid restraining control, the brake for the right rear wheel on the inside of the turn will be applied. Brakes for all wheels may also be activated if necessary. The diagram below indicates hydraulic pressure pathways in pressure increase mode for controlling front wheel skid when the vehicle makes a right-hand turn. In other modes, the pressure holding valve and pressure reduction valve may be turned on or off as required by ABS and EBD activation patterns.

X108419E02
3.104,0.729 2.74,0.333 2.74,0.333 2.563,0.333 true 0.948,2.385 0.708,2.073 0.708,2.073 0.563,2.073 true 1.969,2.396 2.479,2.073 2.479,2.073 2.615,2.073 true 5.146,2.396 4.594,2.073 4.594,2.073 4.458,2.073 true 6.146,2.385 6.417,2.01 6.417,2.01 6.552,2.01 true 5.896,5.271 6.427,4.896 6.427,4.896 6.573,4.896 true 5.865,4.021 5.458,4.427 5.458,4.427 5.333,4.427 true 4.74,4.031 5.125,3.854 5.125,3.854 5.219,3.854 true 2.375,4.021 1.979,4.427 1.979,4.427 1.854,4.427 true 1.25,4 1.635,3.823 1.635,3.823 1.719,3.823 true 4.729,5.26 4.927,5.063 4.927,5.063 5.021,5.063 true 1.208,5.271 0.677,4.896 0.677,4.896 0.531,4.896 true 2.365,5.26 2.167,5.063 2.167,5.063 2.073,5.063 true 3.229,4.99 3.313,5.094 3.313,5.094 3.313,5.667 true 3.885,5 3.771,5.104 3.771,5.104 3.771,5.677 true 3.156,6.625 3.156,7.104 true 3.948,6.625 3.948,7.104 true 5.573,1.677 5.354,1.677 true 5.188,1.552 5.365,1.781 0.177,0.229 10 false *3 2.396,0.219 2.573,0.438 0.177,0.219 10 false *1 0.094,1.448 0.323,1.667 0.229,0.219 10 false *2 0.885,2.99 1.125,3.229 0.24,0.24 10 false (1) 1.865,2.99 2.115,3.25 0.25,0.26 10 false (2) 1.125,4.594 1.396,4.854 0.271,0.26 10 false (5) 2.292,4.594 2.594,4.833 0.302,0.24 10 false (6) 1.146,5.823 1.396,6.083 0.25,0.26 10 false (9) 2.271,5.823 2.563,6.073 0.292,0.25 10 false (10) 0.333,1.948 0.583,2.229 0.25,0.281 10 false (A) 2.656,1.969 2.979,2.24 0.323,0.271 10 false (B) 5.063,2.99 5.302,3.229 0.24,0.24 10 false (3) 6.073,2.99 6.344,3.229 0.271,0.24 10 false (4) 4.656,4.594 4.896,4.844 0.24,0.25 10 false (7) 5.802,4.594 6.094,4.844 0.292,0.25 10 false (8) 4.615,5.823 4.917,6.073 0.302,0.25 10 false (11) 5.76,5.823 6.104,6.115 0.344,0.292 10 false (12) 4.635,7.438 4.844,7.698 0.208,0.26 10 false *8 3.104,7.094 3.313,7.323 0.208,0.229 10 false *5 3.896,7.104 4.104,7.333 0.208,0.229 10 false *5 3.688,5.677 3.948,5.917 0.26,0.24 10 false *4 3.271,5.667 3.49,5.896 0.219,0.229 10 false *4 5.833,7.438 6.052,7.677 0.219,0.24 10 false *9 1.115,7.438 1.365,7.698 0.25,0.26 10 false *6 2.302,7.438 2.521,7.677 0.219,0.24 10 false *7 4.24,1.969 4.5,2.177 0.26,0.208 10 false (C) 6.594,1.906 6.854,2.156 0.26,0.25 10 false (D) 6.604,4.792 6.865,5.094 0.26,0.302 10 false (L) 5.115,4.302 5.375,4.552 0.26,0.25 10 false (H) 5.25,3.75 5.521,4 0.271,0.25 10 false (G) 1.635,4.313 1.865,4.583 0.229,0.271 10 false (F) 1.75,3.729 2.01,3.969 0.26,0.24 10 false (E) 5.063,4.969 5.323,5.229 0.26,0.26 10 false (K) 1.896,4.958 2.115,5.198 0.219,0.24 10 false (J) 0.375,4.802 0.573,5.073 0.198,0.271 10 false (I)

Text in Illustration (VSC Operation (Front Wheel Skid Restraining):)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Rear Brake Caliper (Right Side)
*7 Front Brake Caliper (Left Side) *8 Front Brake Caliper (Right Side)
*9 Rear Brake Caliper (Left Side) - -


iii.

Each valve operates as shown below:

Item Port VSC Not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valve (1) (A) OFF (Open) ON* ON (Closed) ON*
(4) (D) OFF (Open) OFF (Open) OFF (Open) OFF (Open)
Reservoir Cut Solenoid Valve (2) (B) OFF (Closed) ON (Open) ON (Open) ON (Open)
(3) (C) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Front Brakes Pressure Holding Solenoid Valve (6) (F) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
(7) (G) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (10) (J) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
(11) (K) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure Right - - - Increased Held Reduced
Left - - - - - -
Rear Brakes Pressure Holding Solenoid Valve (5) (E) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
(8) (H) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (9) (I) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
(12) (L) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure Right - - - Increased Held Reduced
Left - - - - - -
Pump OFF ON ON ON

HINT:

*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.



iv.

During rear wheel skid restraining control, the brake for the front wheel on the outside of the turn will be applied. The diagram below indicates hydraulic pressure pathways in pressure increase mode for controlling rear wheel skid when the vehicle makes a right-hand turn. In other modes, the pressure holding valve and pressure reduction valve may be turned on or off as required by ABS and EBD activation patterns.

X108742E02
3.104,0.677 2.74,0.281 2.74,0.281 2.563,0.281 true 0.948,2.333 0.708,2.021 0.708,2.021 0.563,2.021 true 1.969,2.333 2.479,2.021 2.479,2.021 2.615,2.021 true 5.135,2.333 4.583,2.01 4.583,2.01 4.448,2.01 true 6.146,2.333 6.417,1.969 6.417,1.969 6.552,1.969 true 5.885,5.198 6.417,4.823 6.417,4.823 6.563,4.823 true 5.865,3.969 5.458,4.385 5.458,4.385 5.333,4.385 true 4.729,3.958 5.115,3.781 5.115,3.781 5.208,3.781 true 2.375,3.958 1.979,4.375 1.979,4.375 1.854,4.375 true 1.229,3.958 1.615,3.781 1.615,3.781 1.698,3.781 true 4.74,5.198 4.927,5.021 4.927,5.021 5.021,5.021 true 1.208,5.219 0.677,4.844 0.677,4.844 0.531,4.844 true 2.365,5.198 2.167,5.01 2.167,5.01 2.073,5.01 true 3.219,4.927 3.313,5.042 3.313,5.042 3.313,5.604 true 3.885,4.948 3.771,5.063 3.771,5.063 3.771,5.625 true 3.156,6.573 3.156,7.052 true 3.948,6.573 3.948,7.052 true 5.573,1.635 5.354,1.635 true 5.177,1.521 5.365,1.74 0.188,0.219 10 false *3 2.396,0.177 2.563,0.406 0.167,0.229 10 false *1 0.094,1.406 0.292,1.667 0.198,0.26 10 false *2 0.885,2.938 1.125,3.219 0.24,0.281 10 false (1) 1.865,2.938 2.146,3.229 0.281,0.292 10 false (2) 1.125,4.542 1.396,4.802 0.271,0.26 10 false (5) 2.292,4.542 2.531,4.781 0.24,0.24 10 false (6) 1.146,5.771 1.438,6.031 0.292,0.26 10 false (9) 2.271,5.771 2.604,6.01 0.333,0.24 10 false (10) 0.344,1.906 0.594,2.167 0.25,0.26 10 false (A) 2.667,1.917 2.969,2.219 0.302,0.302 10 false (B) 5.063,2.938 5.302,3.188 0.24,0.25 10 false (3) 6.073,2.948 6.333,3.229 0.26,0.281 10 false (4) 4.656,4.542 4.938,4.792 0.281,0.25 10 false (7) 5.802,4.542 6.083,4.781 0.281,0.24 10 false (8) 4.615,5.771 4.917,6 0.302,0.229 10 false (11) 5.76,5.771 6.063,6.021 0.302,0.25 10 false (12) 4.635,7.375 4.865,7.635 0.229,0.26 10 false *8 3.094,7.042 3.344,7.292 0.25,0.25 10 false *5 3.896,7.052 4.104,7.281 0.208,0.229 10 false *5 3.688,5.625 3.917,5.896 0.229,0.271 10 false *4 3.271,5.604 3.479,5.823 0.208,0.219 10 false *4 5.833,7.385 6.073,7.635 0.24,0.25 10 false *9 1.115,7.375 1.344,7.625 0.229,0.25 10 false *6 2.302,7.375 2.573,7.635 0.271,0.26 10 false *7 4.229,1.906 4.479,2.146 0.25,0.24 10 false (C) 6.594,1.865 6.833,2.135 0.24,0.271 10 false (D) 6.594,4.708 6.833,4.979 0.24,0.271 10 false (L) 5.125,4.281 5.385,4.531 0.26,0.25 10 false (H) 5.24,3.677 5.5,3.927 0.26,0.25 10 false (G) 1.635,4.25 1.875,4.5 0.24,0.25 10 false (F) 1.75,3.698 2.01,3.948 0.26,0.25 10 false (E) 5.063,4.917 5.313,5.167 0.25,0.25 10 false (K) 1.896,4.917 2.135,5.198 0.24,0.281 10 false (J) 0.375,4.74 0.594,4.979 0.219,0.24 10 false (I)

Text in Illustration (VSC Operation (Rear Wheel Skid Restraining):)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Rear Brake Caliper (Right Side)
*7 Front Brake Caliper (Left Side) *8 Front Brake Caliper (Right Side)
*9 Rear Brake Caliper (Left Side) - -


v.

Each valve operates as shown below:

Item Port VSC Not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON* ON (Closed) ON*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open) ON (Open) ON (Open)
Front Brakes Pressure Holding Solenoid Valve (6) (F) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
(7) (G) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (10) (J) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
(11) (K) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure Right - - - - - -
Left - - - Increased Held Reduced
Rear Brakes Pressure Holding Solenoid Valve (5) (E) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
(8) (H) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (9) (I) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
(12) (L) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure Right - - - - - -
Left - - - - - -
Pump OFF ON ON ON

HINT:

*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.





FAIL-SAFE


a.

If a failure occurs in the skid control ECU, sensors, or brake actuator assembly, the system continues performing brake control by excluding the failed area and using only the areas that are operating normally.



DIAGNOSIS


a.

If the skid control ECU detects a malfunction in the brake control system, the warning lights or indicator light illuminate. At the same time, a Diagnostic Trouble Code (DTC) is stored in the memory of the skid control ECU.


b.

This system has a sensor signal check (test mode) function.


c.

For details of DTCs and the check function, refer to the Repair Manual.