Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM › from 2016.06
NM2090E _54 Brake _060637 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297335 BRAKE CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


Component Function
Combination Meter Assembly Brake System Warning Light
·

Illuminates to alert the driver when the skid control ECU detects a malfunction in the EBD or brake system.

·

Illuminates to alert the driver when the brake fluid level is low.

·

Illuminates to inform the driver of the parking brake condition.


ABS Warning Light Illuminates to alert the driver when the skid control ECU detects a malfunction in the ABS.
Slip Indicator Light
·

Blinks to inform the driver when the TRC and VSC.

·

Illuminates to alert the driver when the skid control ECU detects a malfunction in the TRC or VSC.


VSC OFF Indicator Light
·

Illuminates when the VSC OFF switch (pattern select switch assembly) is pressed for about three seconds to select VSC OFF Mode.*1

·

Illuminates when TRACK Mode is selected.


TRACK Indicator Light Illuminates when TRACK Mode is selected.
TRC OFF Indicator Light
·

Illuminates when the VSC OFF switch (pattern select switch assembly) is pressed briefly to select TRC OFF Mode.*2

·

Illuminates when the VSC OFF switch (pattern select switch assembly) is pressed for about three seconds to select TRC OFF Mode.*1


Hill Start Assist Control Indicator Light The light is on when the hill-start assist control function is on and flashes during operation. During a failure, a buzzer sounds and the light switches off at the same time.
Buzzer When hill-start assist control fails while the hill-start assist control function is on, an alarm sounds to warn the driver.
Master Warning Light*3 Illuminates when the warning message is displayed in the multi-information display.
Multi-information Display*3 Shows a warning message to alert the driver, such as when the vehicle is being driven with the parking brake still engaged.
VSC OFF Switch (Pattern Select Switch Assembly) Enables the driver to select "Normal Mode", "TRC OFF Mode", "VSC OFF Mode" or "VSC/TRC OFF Mode".
TRACK Switch (Pattern Select Switch Assembly) Enables the driver to select Normal Mode or TRACK Mode.
Stop Light Switch Assembly Detects the brake pedal depressing signal.
Steering Sensor Detects the direction and angle of the steering wheel.
Front and Rear Speed Sensors Detects the wheel speed of each of the 4 wheels.
Brake Actuator Assembly Changes the fluid path based on the signals from the skid control ECU during the operation of the brake control system functions, in order to control the fluid pressure applied to the wheel cylinders.
Master Cylinder Pressure Sensor
(Built into Brake Actuator Assembly)
Detects the master cylinder pressure.
Skid Control ECU
·

Judges the vehicle driving condition based on the signals from each sensor, and sends the brake control signals to the brake actuator.

·

Sends an emergency braking signal request signal to the main body ECU (network gateway ECU) based on signals received from each sensor and the operation of the brake pedal.


Yawrate Sensor
(with Built-in Skid Control ECU)
Detects vehicle turning angle velocity and front and rear, left and right acceleration.
ECM Based on the signals received from the skid control ECU, controls the engine output.
Parking Brake Switch Assembly Outputs a parking brake operation signal to the main body ECU (network gateway ECU).
Main Body ECU (Network Gateway ECU) Sends the parking brake switch signal to the main body ECU (network gateway ECU).
Clock Assembly Hazard Warning Signal Switch Transmits a hazard warning light on/off request signal to the main body ECU (network gateway ECU).

HINT:

*1: If the VSC OFF switch (pattern select switch assembly) is pressed for about three seconds, VSC and TRC turn off, and the VSC OFF indicator light and TRC OFF indicator light illuminate simultaneously.

*2: If the vehicle speed exceeds about 50 km/h (31.1 mph) while in TRC OFF mode, TRC automatically turns on, and the TRC OFF indicator light turns off.

*3: Models with TFT LCD type multi-information display



SYSTEM CONTROL


Control Outline
Anti-lock Brake System (ABS) The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface.
Electronic Brake Force Distribution (EBD) The EBD control utilizes ABS, achieving proper brake force distribution between the front and rear wheels in accordance with the driving conditions.
Brake Assist
·

The primary purpose of brake assist is to provide an auxiliary brake force to assist a driver who cannot generate a large brake force during emergency braking, thus helping enhance the vehicle's braking performance.

·

If the skid control ECU judges that the brake pedal force applied by the driver is not sufficient to enhance adequate braking force, brake assist is used to enhance the braking force.


Traction Control (TRC) The TRC helps restrain the slippage of the drive wheels if the driver depresses the accelerator pedal excessively when starting off or while accelerating on a slippery surface.
Limited Slip Differential (LSD) Function The LSD function detects a difference in rotation speeds between the left and right drive wheels. If there is a difference in rotation speeds between them, this function applies brake to the drive wheel that rotates faster than the other using pressurization function of the VSC to minimize the difference.
Vehicle Stability Control (VSC) The VSC helps restrain sideways slippage of the vehicle during a strong front wheel skid or strong rear wheel skid, which may occur while cornering.
Hill-start Assist Control*1 When starting uphill, this control maintains the brake hydraulic pressure on all 4 wheels, in order to momentarily prevent the vehicle from descending backward.
Emergency Brake Signal*2 In the case of emergency braking, the emergency brake signal flashers the hazard warning lights to alert drivers in following vehicles.

HINT:

*1: Hill-start assist control is off by default.

*2: Except Models for Korea


a.

Anti-lock Brake System (ABS)

i.

The ABS helps prevent the wheels from locking during sudden braking or braking on a slippery surface. This provides the proper braking force when the vehicle slips, thus ensuring vehicle stability and excellent braking performance.

X102923E04
1.448,2.198 1.823,2.573 0.375,0.375 12 false *B: 1.448,0.865 1.823,1.24 0.375,0.375 12 false *A: 4.573,0.927 4.823,1.167 0.25,0.24 10 false *a

Text in Illustration (Illustration Provides Conceptual Image:)
*A Models with ABS *B Models without ABS
*a Brake Operation - -



b.

Electronic Brake Force Distribution (EBD)

i.

This function controls the brake force that acts on the rear wheels in accordance with the changes in the vehicle conditions such as load factors or deceleration, in order to enhance excellent braking performance.

X100697E01
1.948,1.719 1.781,1.719 1.781,1.719 1.781,2.563 true 4.917,1.406 4.74,1.406 4.74,1.406 4.74,2.375 true 2.406,2.635 2.229,2.635 2.229,2.635 2.063,2.49 true 5.417,2.604 5.24,2.604 5.24,2.604 5.073,2.458 true 0.594,2.135 1.344,2.542 0.75,0.406 10 Rear Brake Force 3.583,2.135 4.344,2.781 0.76,0.646 10 Rear Brake Force 1.99,1.635 3.125,2.031 1.135,0.396 10 Ideal Brake Force Distribution 4.958,1.323 6.104,1.708 1.146,0.385 10 Ideal Brake Force Distribution 2.438,2.542 3.229,2.854 0.792,0.313 10 EBD Control 5.448,2.531 6.24,2.844 0.792,0.313 10 EBD Control 1.729,2.917 2.885,3.24 1.156,0.323 10 Front Brake Force 4.74,2.917 5.896,3.24 1.156,0.323 10 Front Brake Force 1.667,3.281 3.01,3.625 1.344,0.344 10 Without Load in Rear 4.781,3.292 5.927,3.625 1.146,0.333 10 With Load in Rear



c.

Brake Assist

i.

During the brake assist, the skid control ECU calculates the speed and the amount of the brake pedal application based on the signals from the master cylinder pressure sensor and then determines the intention of the driver to make an emergency brake application. If the skid control ECU determines that the driver intends to make an emergency brake application, this function activates the brake actuator to increase the brake fluid pressure, which increases the brake force.

X108794E02
0.854,2.948 3.979,3.323 3.125,0.375 10 false Fluid Pressure Increased by Brake Actuator 1.073,0.354 2.302,0.833 1.229,0.479 10 false Skid Control ECU 1.167,1.448 2.313,1.781 1.146,0.333 10 false Brake Actuator 3.938,0.823 4.406,1.677 0.469,0.854 10 false Brake Force 5.573,2.792 6.323,3.146 0.75,0.354 10 false Time 4.99,1.646 6.25,2.01 1.26,0.365 10 false With Brake Assist 4.771,2.323 6.313,2.646 1.542,0.323 10 false Without Brake Assist



d.

Traction Control (TRC)

i.

The TRC helps prevent the drive wheels from slipping if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface. Simultaneously with the hydraulic brake control of the drive wheels, the skid control ECU makes a request to the ECM to effect engine output control. This produces the drive force that suits the driving conditions, in order to enhance the proper start-off acceleration.

X102925E02
5.021,1.458 4.531,1.458 true 5.01,1.052 4.521,1.052 true 6.115,1.896 5.458,1.896 true 4.354,1.354 4.552,1.604 0.198,0.25 10 false *2 2.563,0.313 2.844,0.615 0.281,0.302 12 false *B: 0.948,0.313 1.229,0.604 0.281,0.292 12 false *A: 4.344,0.948 4.521,1.177 0.177,0.229 10 false *1 6.146,1.792 6.365,2.052 0.219,0.26 10 false *a

Text in Illustration (Driving on Road with Differing Surface Friction Characteristics:)
*A Models without TRC *B Models with TRC
*1 ECM
- Engine Output Control
*2 Brake Actuator Assembly
- Hydraulic Brake Control
*a Brake Slipping Drive Wheel - -
V100145

Slippery Surface - -



e.

Limited Slip Differential (LSD) Function

i.

The LSD function detects a difference in rotation speeds between the left and right drive wheels. If there is a difference in rotation speeds between them, this function applies brake to the drive wheel that rotates faster than the other using pressurization function of the VSC* to minimize the difference.


ii.

This function makes it possible to start and accelerate the vehicle stably.

HINT:

*: In the case of an A/T vehicle, brake LSD function is maintained regardless of whether VSC Mode is on or off, but the control parameters change. In the case of a M/T vehicle, this function is stopped VSC Mode is off. This enabled traveling in the original base state.




f.

Vehicle Stability Control (VSC)

i.

The following are 2 examples that can be considered circumstances in which the tires exceed their lateral grip limit. The VSC is designed to help control the vehicle behavior by controlling the engine output and the brakes of each wheel when the vehicle is under one of the conditions indicated below:

X102948E01
4.696,2.1 5.333,2.377 0.638,0.277 10 *b 2.154,2.1 2.792,2.377 0.638,0.277 10 *a

Text in Illustration
*a Front Wheel Skid Tendency (Understeer)
- When the front wheels lose grip in relation to the rear wheel
*b Rear Wheel Skid Tendency (Oversteer)
- When the rear wheels lose grip in relation to the front wheels


ii.

The vehicle's sideways skid tendency is determined by the skid control computer based on the target yaw rate and actual vehicle yaw rate values.


iii.

Whether or not the vehicle is experiencing a front wheel skid is determined by the difference between the target yaw rate and the vehicle's actual yaw rate. When the vehicle's actual yaw rate is smaller than the target yaw rate (which is determined based on the vehicle speed and steering angle) that should be generated when the driver operates the steering wheel, it means the vehicle is making a turn at a greater angle than the target locus of travel. Thus, the skid control ECU determines that there is a large front wheel skid tendency.

X102926E01
3.366,0.042 3.752,0.288 0.386,0.247 10 *a 4.744,0.75 5.129,0.996 0.386,0.247 10 *b

Text in Illustration
*a Actual Locus of Travel (Actual Yaw Rate) *b Locus of Travel Based on Target Yaw Rate


iv.

Whether or not the vehicle is experiencing a rear wheel skid is determined by the values of the vehicle's slip angle and the vehicle's slip angular velocity (time-dependent changes in the vehicle's slip angle). When the vehicle's slip angle is large, and the slip angular velocity is also large, the skid control ECU determines that the vehicle has a large rear wheel skid tendency.

X102927E01
3.566,0.029 3.852,0.287 0.286,0.258 10 *a 3.902,0.174 4.188,0.432 0.286,0.258 10 *b

Text in Illustration
*a Travel Direction of Vehicle's Center of Gravity *b Movement of Vehicle
V100136

Slip Angle - -


v.

When the skid control ECU determines that the vehicle is exhibiting a tendency to experience a front wheel skid or a rear wheel skid, it decreases the engine output and applies the brakes of each wheel to control the vehicle's yaw moment. The basic operation of the VSC is described below. However, the control method differs depending on the vehicle's characteristics and driving conditions.


vi.

When the skid control ECU determines that there is a front wheel skid tendency, it applies the brake on the rear wheel on the inside of the turn in accordance with the extent of the skid tendency in order to help restrain the front wheel from skidding.

X108795

Text in Illustration
V100136

Control Moment
V100135

Brake Force


vii.

When the skid control ECU determines that there is a large rear wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. It applies the brakes of the front wheel of the outer circle of the turn, and generates an outward moment of inertia in the vehicle, in order to restrain the rear wheel skid tendency. Along with the reduction in the vehicle speed caused by the braking force, excellent vehicle stability is enhanced. In some cases, the skid control ECU applies the brake of the rear wheels, as necessary.

X108796

Text in Illustration
V100136

Control Moment
V100135

Brake Force



g.

Hill-start Assist Control

i.

When the vehicle starts off on a steep or slippery hill, it may start to descend backward while the driver switches from the brake pedal to the accelerator pedal, thus making it difficult for the vehicle to start off. To prevent this from occurring, the hill-start assist control temporarily (approximately 2 seconds at the maximum) applies the brakes to the 4 wheels in order to prevent the vehicle from descending backward.


ii.

Without the hill-start assist control, the driver must quickly and precisely switch from the brake pedal to the accelerator pedal. With the hill-start assist control, however, the driver a start off easily and operate the pedal in a relaxed manner, because the hill-start assist control prevents the vehicle from descending backward.

X112168E06
0.5,0.167 0.76,0.417 0.26,0.25 10 false *a 3.875,0.177 4.198,0.448 0.323,0.271 10 false *b 1.542,1.958 1.781,2.208 0.24,0.25 10 false *c

Text in Illustration
*a Models with Hill-start Assist Control *b Models without Hill-start Assist Control
*c Prevents vehicle from descending backward by controlling brakes. - -


iii.

Hill-start assist control is off by default. It can be switched on through a user operation.


iv.

To enable the hill-start assist control function, perform the following procedure.

Step Method of Operation
1 Park the vehicle in a stable location in which the ground is flat and solid.
2 Make sure that the parking brake is engaged securely.
3 Set the ignition switch off.
4 Start the engine, and then make sure that the ABS warning and slip indicator lights are off.
5 Press and hold the VSC OFF switch. (The VSC OFF indicator light switches on.) Continue pressing until the VSC OFF indicator light switches off (after about 30 seconds).
6 After the VSC OFF indicator light switches off, release the switch within 5 seconds.
7 After releasing the switch, press the VSC OFF switch again within 2 seconds. The hill-start assist control indicator light switches on, and then the hill-start assist control indicator light switches off.
8 Set the ignition switch off. If the engine is started again, the hill-start assist control indicator light stays on, indicating that the hill-start assist control function is on.

HINT:
·

When the hill-start assist control function is on, the hill-start assist control indicator light is on.

·

If the hill-start assist control function is switched on once by the driver, the hill-start assist control function stays on even if the ignition switch off.

·

When the vehicle is stopped on a hill road, and the hill-start assist control function operation conditions are satisfied, the hill-start assist control indicator light flashes. When the vehicle starts from a stop, the driver is notified that the brake is being maintained temporarily.

·

If the brake is released and an accelerator pedal operation is recognized, the retention of brake fluid pressure is released, and the vehicle can depart. (The brake fluid pressure is released about 2 seconds after the brake is released.)

·

When a failure has occurred that disables maintenance of the hill-start assist control function while the function is on, the hill-start assist control indicator light switches off and a buzzer sounds at the same time to notify the driver.

·

The hill-start assist control indicator light is off when the hill-start assist control function is on.




v.

Procedure to switch off the hill-start assist control function

Step Method of Operation
1 Park the vehicle in a stable location in which the ground is flat and solid.
2 Make sure that the parking brake is engaged securely.
3 Set the ignition switch off.
4 Start the engine, and then make sure that the ABS warning and slip indicator lights are off. And make sure that the hill-start assist control indicator light are on.
5 Press and hold the VSC OFF switch. (The VSC OFF indicator light switches on.) Continue pressing until the VSC OFF indicator light switches off (after about 30 seconds).
6 After the VSC OFF indicator light switches off, release the switch within 5 seconds.
7 After releasing the switch, press the VSC OFF switch again within 2 seconds. The hill-start assist control indicator light switches off (2 seconds), and then the hill-start assist control indicator light switches on.
8 Set the ignition switch off. If the engine is started again, the hill-start assist control indicator light off, indicating that the hill-start assist control function is off.

HINT:
·

The hill-start assist control indicator light is off when the hill-start assist control function is off.




vi.

Hill-start Assist Control Activation Conditions

·

The skid control ECU judges if the vehicle is on an uphill incline based on signals from the deceleration sensor, and activates hill-start assist control when the vehicle is started with all of the following conditions met.

Hill-start Assist Control Activation Conditions
·

The shift lever is in any position other than P or N (Forward climbing and backward climbing).*1

·

The shift lever is in a position other than R when starting off forward on an upward incline or in R when starting off backward on an upward incline.*2

·

The vehicle is at a standstill.

·

The accelerator pedal is not depressed.

·

The parking brake is released.

·

There are no errors with the VSC system.

·

The hill-start assist control indicator light is on.

·

Hill-start assist control is set to ON.

·

When the ignition switch ON.

·

The clutch is not engaged.*2



HINT:

*1: Models with A/T

*2: Models with M/T




vii.

Hill-start Assist Control Cancelation Conditions

·

If any of the following conditions is met, hill-start assist control operation is canceled.

Hill-start Assist Control Cancelation Conditions
·

The shift lever is moved to P or N.*1

·

The shift lever is shifted to R when starting off forward on an upward incline or from R when starting off backward on an upward incline.*2

·

The accelerator pedal is depressed.

·

The parking brake is operated.

·

Approximately 2 seconds elapse since the operation started.

·

There is an error in the VSC system.*3

·

There is an error in the hill-start assist control system.

·

When the ignition switch ACC or off.

·

The clutch is engaged.*2



HINT:

*1: Models with A/T

*2: Models with M/T

*3: When a failure has occurred while hill-start assist control is on, the hill-start assist control indicator light switches off, and the buzzer sounds.





h.

Emergency brake signal

i.

The emergency brake signal automatically flashes the hazard warning lights in the case of emergency braking in order to reduce the risk of being rear ended by a following vehicle.


ii.

The skid control ECU detects the vehicle condition and braking operation using the speed sensors and stop light switch assembly.


iii.

If emergency braking is detected based on these various signals, the skid control ECU sends a signal to the main body ECU (network gateway ECU) to flash the hazard warning lights.


iv.

Emergency brake signal operating conditions are as shown in the following table.

Operating Condition
Activating Conditions When all of the following conditions are met, the emergency brake signal starts operating:
·

Vehicle speed is over 60 km/h (38 mph).

·

Driver is depressing the brake pedal.

·

Emergency braking is detected from the vehicle deceleration.


Deactivating Conditions When any of the following conditions is met, emergency brake signal stops operating:
·

Driver has released the brake pedal.

·

Emergency braking is no longer detected from the vehicle deceleration.

·

Driver has pressed the hazard warning signal switch.






FUNCTION


a.

VSC OFF Switch (Pattern Select Switch Assembly)

i.

The operation of the VSC and TRC functions can be stopped by the VSC OFF switch (pattern select switch assembly). While the vehicle is running off the shoulder of the road or running on a dirt road, the engine output control is stopped to maintain drive torque.

X108406E02
5.531,1.979 5.531,2.323 true 1.667,0.646 1.875,0.854 0.208,0.208 10 false *2 1.146,0.656 1.354,0.865 0.208,0.208 10 false *1 5.458,2.344 5.667,2.552 0.208,0.208 10 false *3

Text in Illustration
*1 VSC OFF Indicator Light *2 TRC OFF Indicator Light
*3 VSC OFF Switch (Pattern Select Switch Assembly) - -


ii.

The VSC OFF switch (pattern select switch assembly) can select 3 modes (Normal mode, TRC OFF mode, and VSC OFF mode).


iii.

Briefly pressing the VSC OFF switch (pattern select switch assembly) in Normal mode selects TRC OFF mode.


iv.

Pressing and holding the VSC OFF switch (pattern select switch assembly) for 3 seconds or more will disable the VSC and TRC functions.


v.

Briefly pressing the VSC OFF switch (pattern select switch assembly) in TRC OFF mode or VSC OFF mode or turning the ignition switch off returns to the Normal mode.

X102940E02
3.5,0.573 3.844,0.865 0.344,0.292 10 false *a 4.875,1.813 5.219,2.104 0.344,0.292 10 false *b 2.083,1.802 2.427,2.094 0.344,0.292 10 false *c

Text in Illustration
*a Normal Mode *b TRC OFF Mode
*c VSC OFF Mode and TRC OFF Mode - -
V100135

VSC OFF Switch (Pattern Select Switch Assembly) Operation (Press and Hold for 3 Seconds or More)
V100136

VSC OFF Switch (Pattern Select Switch Assembly) Operation (Brief)


vi.

The operations of the brake control functions in each mode are as follows:

Mode Brake Control Function Combination Meter Assembly
TRC VSC Slip Indicator Light TRC OFF Indicator Light VSC OFF Indicator Light
Normal Mode Controllable Controllable Blinks*1 - -
TRC OFF Mode Not Controllable Controllable Blinks*2 Illuminates -
VSC/TRC OFF Mode Not Controllable Not Controllable*3 Blinks*3 Illuminates Illuminates

HINT:

*1: When VSC/TRC is active

*2: When VSC is active

*3: If there is a major variance between the left and right driving wheels, the brakes might be applied (A/T Models).




b.

TRACK Switch (Pattern Select Switch Assembly)

i.

Use this TRACK switch (pattern select switch assembly) to allow the skid control ECU to switch VSC control between Normal Mode and TRACK Mode.


ii.

Press the TRACK switch (pattern select switch assembly) to switch VSC to TRACK Mode. When this happens, the driver will be informed that the vehicle is in TRACK Mode by the illumination of the TRACK indicator light and VSC OFF indicator light in the combination meter assembly.

X133917E02
6.49,1.938 6.49,2.323 true 6.427,2.375 6.635,2.583 0.208,0.208 10 false *2 0.99,0.635 1.198,0.844 0.208,0.208 10 false *1

Text in Illustration
*1 TRACK Indicator Light *2 TRACK Switch (Pattern Select Switch Assembly)

X133916E01
2.071,1.283 2.276,1.488 0.205,0.205 10 *a 4.854,1.283 5.059,1.488 0.205,0.205 10 *b

Text in Illustration
*a Normal Mode *b TRACK Mode
V100135

TRACK Switch (Pattern Select Switch Assembly) Operation (Press and Hold for 1 Second or More)
V100136

TRACK Switch (Pattern Select Switch Assembly) Operation (Brief)

X134649E03
3.615,4.917 4.156,5.24 0.542,0.323 10 false Mode 1 1.656,6.052 2.219,6.354 0.563,0.302 10 false Mode 2 5.552,6.01 6.094,6.313 0.542,0.302 10 false Mode 4 3.594,7.125 4.135,7.458 0.542,0.333 10 false Mode 3 0.688,7.5 3.052,7.906 2.365,0.406 12 false VSC OFF Switch Operation: 4.396,7.5 6.479,7.906 2.083,0.406 12 false TRACK Switch Operation: 1.771,8.479 3.813,8.823 2.042,0.344 10 false : More than 3 seconds press 5.344,8.156 6.49,8.458 1.146,0.302 10 false : Quickly Press 5.344,8.5 7.094,8.844 1.75,0.344 10 false : More than 1 second press 1.771,8.156 2.927,8.479 1.156,0.323 10 false : Quickly Press 0.229,4.458 2.344,4.948 2.115,0.49 12 false Mode Transition Diagram: 0.094,0.042 2.208,0.365 2.115,0.323 12 false Mode Transitions: 2.448,0.51 3.042,1.115 0.594,0.604 10 false VSC Function 2.594,3.656 2.906,4.146 0.313,0.49 10 false OFF 3.281,3.656 3.625,4.094 0.344,0.438 10 false OFF 2.552,2.917 2.948,3.396 0.396,0.479 10 false Sport 2.531,1.552 3.021,1.896 0.49,0.344 10 false Normal 2.521,2.104 3.042,2.573 0.521,0.469 10 false Normal 0.948,1.531 2.438,1.906 1.49,0.375 10 false Mode 1 (Normal Mode) 0.198,1.406 0.74,2.073 0.542,0.667 10 false Normal Driving 0.177,3.125 0.74,4.146 0.563,1.021 10 false Sportier Driving 0.927,1.969 2.354,2.667 1.427,0.698 10 false Mode 2 (TRC OFF Mode) 0.927,2.75 2.385,3.365 1.458,0.615 10 false Mode 3 (TRACK Mode) 0.927,3.521 2.396,4.188 1.469,0.667 10 false Mode 4 (VSC/TRC OFF Mode) 3.125,0.51 3.708,1.177 0.583,0.667 10 false TRC Function 3.302,2.917 3.583,3.396 0.281,0.479 10 false ON 3.271,2.115 3.615,2.583 0.344,0.469 10 false OFF 3.302,1.563 3.583,1.906 0.281,0.344 10 false ON 4.823,0.427 5.771,1.094 0.948,0.667 10 false TRC OFF Indicator Light 5.844,0.417 6.823,1.083 0.979,0.667 10 false TRACK Indicator Light 3.823,0.427 4.719,1.125 0.896,0.698 10 false VSC OFF Indicator Light 3.885,2.927 4.625,3.417 0.74,0.49 10 false Illuminates 4.948,2.115 5.688,2.604 0.74,0.49 10 false Illuminates 5.969,2.906 6.708,3.396 0.74,0.49 10 false Illuminates 4.958,3.646 5.698,4.073 0.74,0.427 10 false Illuminates 3.917,3.625 4.656,4.052 0.74,0.427 10 false Illuminates




CONSTRUCTION


a.

Steering Sensor

i.

The steering sensor detects the steering direction and angle, and sends this information to the skid control ECU.

X108408E03
3.552,2.031 4.219,2.396 4.219,2.396 3.313,2.115 true 3.625,1.74 4.833,1.26 true 4.26,2.344 4.5,2.594 0.24,0.25 10 false *2 4.854,1.146 5.063,1.375 0.208,0.229 10 false *1 2.052,0.396 2.26,0.615 0.208,0.219 10 false *a

Text in Illustration
*1 Steering Sensor *2 Detection Gear
*a Front - -



b.

Speed Sensor

i.

An active type speed sensor is used. This sensor contains a Hall IC.


ii.

The sensor rotor, which consists of N and S poles that are arranged in a circle, is integrated with the hub bearing inner race.


iii.

An active type speed sensor uses a Hall IC to detect magnetic field changes caused when the sensor rotor rotates, and the sensor outputs the detected information to the skid control ECU as digital pulses.


iv.

To detect the vehicle speed, the frequency of the output pulses is used. Because the active sensor outputs vehicle speed pulses, the speed of the vehicle can be detected at speeds of 1.35 km/h (0.84 mph) or higher.

X100718E18
5.177,3.177 5.344,2.99 5.344,2.99 5.604,2.99 true 4.333,6.792 4.5,6.604 4.5,6.604 4.76,6.604 false 1.969,2.094 3.073,2.427 1.104,0.333 10 false Sensor Rotor 4,1.281 4.573,1.635 0.573,0.354 10 false Hall IC 5.656,2.896 6.76,3.229 1.104,0.333 10 false Speed Sensor 1.625,4.375 3.385,4.719 1.76,0.344 10 false N and S Poles Arrangement 2.135,5.479 2.646,5.958 0.51,0.479 10 false Vehicle Speed 2.135,6.542 2.646,7.021 0.51,0.479 10 false Sensor Output 4.833,6.51 5.938,6.844 1.104,0.333 10 false Digital Pulses 3.469,7.292 3.854,7.594 0.385,0.302 10 false Time



c.

Brake Actuator Assembly

i.

The brake actuator assembly consists of the brake actuator portion and skid control ECU.

X108410E02
3.521,0.531 4.521,0.219 4.521,0.219 4.667,0.219 true 3.281,0.583 2.688,0.24 2.688,0.24 2.542,0.24 true 2.906,0.958 2.302,0.677 2.302,0.677 2.125,0.677 true 3.865,0.698 4.823,1.052 4.823,1.052 4.969,1.052 true 4.135,1.615 4.875,1.938 4.875,1.938 5.021,1.938 true 3.99,1.802 4.75,2.531 4.75,2.531 4.927,2.531 true 2.156,2.042 1.677,1.823 1.677,1.823 1.51,1.823 true 3.875,2.313 4.188,2.594 4.188,2.594 4.365,2.594 true 2.365,0.125 2.542,0.365 0.177,0.24 10 false *4 1.948,0.573 2.135,0.792 0.188,0.219 10 false *3 1.333,1.719 1.521,1.958 0.188,0.24 10 false *2 4.708,0.125 4.969,0.354 0.26,0.229 10 false *5 5,0.938 5.219,1.167 0.219,0.229 10 false *6 5.063,1.833 5.281,2.104 0.219,0.271 10 false *7 4.969,2.417 5.188,2.646 0.219,0.229 10 false *8 4.396,2.479 4.594,2.698 0.198,0.219 10 false *1

Text in Illustration
*1 Brake Actuator Portion *2 Skid Control ECU
*3 Right Rear Brake Pipe *4 Left Front Brake Pipe
*5 Right Front Brake Pipe *6 Left Rear Brake Pipe
*7 Master Cylinder Pipe (Primary Side) *8 Master Cylinder Pipe (Secondary Side)


ii.

The actuator portion consists of 2 master cylinder cut solenoid valves, 2 reservoir cut solenoid valves, 4 pressure holding solenoid valves, 4 pressure reduction solenoid valves, 2 pumps, 2 reservoirs, and a master cylinder pressure sensor.

X108411E02
3.323,0.74 2.906,0.24 2.906,0.24 2.781,0.24 true 3.26,4.969 3.385,5.156 3.385,5.156 3.385,5.625 true 3.958,4.969 3.833,5.156 3.833,5.156 3.833,5.625 true 3.208,6.583 3.208,7 true 4,6.583 4,7 true 5.625,1.635 5.427,1.635 true 2.615,0.125 2.781,0.344 0.167,0.219 10 false *1 0.948,2.958 1.177,3.198 0.229,0.24 10 false *4 0.146,1.365 0.344,1.583 0.198,0.219 10 false *2 1.938,2.958 2.177,3.188 0.24,0.229 10 false *5 1.198,4.552 1.448,4.771 0.25,0.219 10 false *6 2.375,4.552 2.635,4.76 0.26,0.208 10 false *6 1.198,5.792 1.438,6.031 0.24,0.24 10 false *7 2.375,5.792 2.625,6.031 0.25,0.24 10 false *7 1.198,7.385 1.531,7.604 0.333,0.219 10 false *10 2.385,7.385 2.719,7.604 0.333,0.219 10 false *11 4.667,7.396 4.969,7.625 0.302,0.229 10 false *12 5.875,7.396 6.198,7.646 0.323,0.25 10 false *13 3.146,7 3.375,7.229 0.229,0.229 10 false *9 3.948,7 4.177,7.229 0.229,0.229 10 false *9 3.74,5.625 3.938,5.844 0.198,0.219 10 false *8 3.323,5.625 3.573,5.854 0.25,0.229 10 false *8 4.708,4.552 4.948,4.771 0.24,0.219 10 false *6 5.865,4.552 6.094,4.76 0.229,0.208 10 false *6 4.708,5.781 5,6.01 0.292,0.229 10 false *7 5.865,5.781 6.146,6.031 0.281,0.25 10 false *7 5.25,1.531 5.438,1.75 0.188,0.219 10 false *3 5.146,2.958 5.396,3.198 0.25,0.24 10 false *5 6.115,2.958 6.365,3.208 0.25,0.25 10 false *4

Text in Illustration
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Master Cylinder Cut Solenoid Valve
*5 Reservoir Cut Solenoid Valve *6 Pressure Holding Solenoid Valve
*7 Pressure Reduction Solenoid Valve *8 Pump
*9 Reservoir *10 Rear Brake Caliper (Right Side)
*11 Front Brake Caliper (Left Side) *12 Front Brake Caliper (Right Side)
*13 Rear Brake Caliper (Left Side) - -




OPERATION


a.

ABS and EBD

i.

Based on the signals received from the 4 speed sensors, the skid control ECU calculates the speed of each wheel, and checks the wheel slipping conditions. In accordance with the slipping condition, the skid control ECU controls each solenoid valve in the brake actuator in order to adjust the fluid pressure of each wheel cylinder in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes.

X102082E03
2.906,2.802 3.583,2.521 true 2.938,0.719 3.594,0.958 true 6.333,3.375 6.677,3.677 0.344,0.302 10 false *e 5.792,0.188 6.104,0.427 0.313,0.24 10 false *c 3.5,0.156 3.844,0.438 0.344,0.281 10 false *b 2.688,2.76 2.948,3.042 0.26,0.281 10 false *4 1.219,3.229 1.563,3.531 0.344,0.302 10 false *2 1.219,1.646 1.563,1.948 0.344,0.302 10 false *1 2.76,0.583 3.104,0.885 0.344,0.302 10 false *3 1.271,0.146 1.594,0.417 0.323,0.271 10 false *a 1.781,3.396 2.125,3.698 0.344,0.302 10 false *d

Text in Illustration
*1 Pressure Holding Solenoid Valve *2 Pressure Reduction Solenoid Valve
*3 Port A *4 Port B
*a Pressure Increase Mode *b Pressure Holding Mode
*c Pressure Reduction Mode *d to Wheel Cylinder
*e from Wheel Cylinder - -


ii.

Each valve operates as shown below:

Pressure Mode Increase Mode Holding Mode Reduction Mode
Pressure Holding Solenoid Valve (Port A) Off (Open) On (Closed) On (Closed)
Pressure Reduction Solenoid Valve (Port B) Off (Closed) Off (Closed) On (Open)
Wheel Cylinder Pressure Increases Holds Reduces



b.

Brake Assist

i.

In the event of emergency braking, the skid control ECU determines the driver's intention based on the speed of the pressure increase in the master cylinder determined by the master cylinder pressure sensor signal. If the skid control ECU judges the need for additional brake assist, pressure is generated by the pump in the brake actuator and directed to the wheel cylinder to apply a large amount of fluid pressure.

X108412E02
0.656,1.135 2.135,1.479 1.479,0.344 10 false Speed Sensor (4) 0.313,3.729 2.26,4.073 1.948,0.344 10 false Stop Light Switch Assembly 3.125,0.573 4.125,0.958 1,0.385 10 false Solenoid Relay 3.063,2.063 4.292,2.719 1.229,0.656 10 false Skid Control ECU 3.198,3.625 4.073,3.979 0.875,0.354 10 false Motor Relay 3.281,2.979 4.052,3.323 0.771,0.344 10 false G Sensor 3.083,4.24 4.125,4.573 1.042,0.333 10 false Yawrate Sensor 5.281,0.417 6.667,1.104 1.385,0.688 10 false Master Cylinder Cut Solenoid Valve (2) 5.198,1.229 6.729,1.896 1.531,0.667 10 false Reservoir Cut Solenoid Valve (2) 5.021,2.031 6.802,2.698 1.781,0.667 10 false Pressure Holding Solenoid Valve (4) 5,2.844 6.802,3.51 1.802,0.667 10 false Pressure Reduction Solenoid Valve (4) 5.521,3.635 6.563,3.969 1.042,0.333 10 false Pump Motor 5.115,4.125 6.75,4.792 1.635,0.667 10 false Master Cylinder Pressure Sensor 2.708,5.323 4.625,5.667 1.917,0.344 10 false Combination Meter Assembly 5.406,4.969 7.073,5.438 1.667,0.469 10 false Brake Actuator Assembly 3,5.802 4.469,6.146 1.469,0.344 10 false Brake Warning Light 3.042,6.208 4.469,6.563 1.427,0.354 10 false ABS Warning Light 3.719,4.948 4.76,5.271 1.042,0.323 10 false CAN (V Bus)

X108413E02
3.156,0.635 2.781,0.24 2.781,0.24 2.604,0.24 true 1,2.281 0.76,1.969 0.76,1.969 0.615,1.969 true 2.021,2.281 2.531,1.969 2.531,1.969 2.677,1.969 true 5.188,2.281 4.635,1.958 4.635,1.958 4.49,1.958 true 6.208,2.292 6.479,1.927 6.479,1.927 6.625,1.927 true 5.948,5.156 6.479,4.781 6.479,4.781 6.615,4.781 true 5.927,3.927 5.521,4.344 5.521,4.344 5.406,4.344 true 4.781,3.917 5.167,3.74 5.167,3.74 5.26,3.74 true 2.427,3.927 2.021,4.344 2.021,4.344 1.896,4.344 true 1.292,3.927 1.677,3.75 1.677,3.75 1.771,3.75 true 4.792,5.167 5,4.958 5,4.958 5.083,4.958 true 1.26,5.177 0.729,4.802 0.729,4.802 0.583,4.802 true 2.417,5.167 2.219,4.969 2.219,4.969 2.115,4.969 true 3.281,4.896 3.396,5.01 3.396,5.01 3.396,5.573 true 3.948,4.906 3.823,5.021 3.823,5.021 3.823,5.583 true 3.208,6.521 3.208,6.99 true 4,6.531 4,7 true 5.625,1.594 5.417,1.594 true 5.24,1.479 5.427,1.708 0.188,0.229 10 false *3 2.438,0.135 2.604,0.365 0.167,0.229 10 false *1 0.146,1.365 0.354,1.635 0.208,0.271 10 false *2 0.938,2.896 1.229,3.198 0.292,0.302 10 false (1) 1.906,2.896 2.208,3.156 0.302,0.26 10 false (2) 1.177,4.5 1.479,4.75 0.302,0.25 10 false (5) 2.354,4.49 2.667,4.719 0.313,0.229 10 false (6) 1.208,5.729 1.448,6.063 0.24,0.333 10 false (9) 2.323,5.729 2.625,6.01 0.302,0.281 10 false (10) 0.406,1.865 0.667,2.156 0.26,0.292 10 false (A) 2.719,1.875 3.01,2.177 0.292,0.302 10 false (B) 5.125,2.896 5.365,3.167 0.24,0.271 10 false (3) 6.125,2.896 6.438,3.167 0.313,0.271 10 false (4) 4.708,4.5 5.01,4.74 0.302,0.24 10 false (7) 5.865,4.5 6.167,4.76 0.302,0.26 10 false (8) 4.667,5.729 4.99,6.01 0.323,0.281 10 false (11) 5.823,5.729 6.146,6.052 0.323,0.323 10 false (12) 4.708,7.333 4.958,7.604 0.25,0.271 10 false *8 3.146,6.99 3.365,7.24 0.219,0.25 10 false *5 3.948,7 4.167,7.219 0.219,0.219 10 false *5 3.75,5.573 3.958,5.802 0.208,0.229 10 false *4 3.344,5.573 3.542,5.823 0.198,0.25 10 false *4 5.885,7.344 6.156,7.594 0.271,0.25 10 false *9 1.177,7.333 1.448,7.573 0.271,0.24 10 false *6 2.375,7.333 2.594,7.604 0.219,0.271 10 false *7 4.271,1.854 4.521,2.135 0.25,0.281 10 false (C) 6.667,1.823 6.927,2.083 0.26,0.26 10 false (D) 6.667,4.667 6.927,4.948 0.26,0.281 10 false (L) 5.188,4.229 5.427,4.5 0.24,0.271 10 false (H) 5.302,3.646 5.563,3.927 0.26,0.281 10 false (G) 1.688,4.229 1.927,4.531 0.24,0.302 10 false (F) 1.802,3.646 2.063,3.927 0.26,0.281 10 false (E) 5.125,4.865 5.365,5.146 0.24,0.281 10 false (K) 1.948,4.875 2.198,5.156 0.25,0.281 10 false (J) 0.427,4.698 0.656,4.99 0.229,0.292 10 false (I)

Text in Illustration (Brake Assist Operation:)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Rear Brake Caliper (Right Side)
*7 Front Brake Caliper (Left Side) *8 Front Brake Caliper (Right Side)
*9 Rear Brake Caliper (Left Side) - -


ii.

Each valve operates as shown below:

Item Port Brake Assist Not Activated Brake Assist Activated
Master Cylinder Cut Solenoid Valves (1), (4) (A), (D) OFF (Open) ON*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open)
Front Brakes Pressure Holding Solenoid Valves (6), (7) (F), (G) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valves (10), (11) (J), (K) OFF (Closed) OFF (Closed)
Rear Brakes Pressure Holding Solenoid Valves (5), (8) (E), (H) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valves (9), (12) (I), (L) OFF (Closed) OFF (Closed)
Pump OFF ON

HINT:

*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.




c.

TRC

i.

The fluid pressure generated by the pump is regulated by the master cylinder cut solenoid valve to the required pressure. Thus, the wheel cylinders of the drive wheels are controlled in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes to control the slippage of the drive wheels.

X133918E03
0.667,1.042 1.896,1.375 1.229,0.333 10 false Speed Sensor (4) 0.531,3.115 2.052,3.448 1.521,0.333 10 false Pattern Select Switch 0.729,3.625 1.875,3.958 1.146,0.333 10 false TRACK Switch 0.635,4.156 1.781,4.49 1.146,0.333 10 false VSC OFF Switch 1.01,5.885 1.479,6.219 0.469,0.333 10 false ECM 0.333,6.979 2.208,7.656 1.875,0.677 10 false Transmission Control ECU Assembly* 0.313,8.302 2.729,8.771 2.417,0.469 10 false *: Models with A/T 3.771,6.75 4.698,7.083 0.927,0.333 10 false CAN (V Bus) 3.125,0.49 4.115,0.823 0.99,0.333 10 false Solenoid Relay 3.052,1.854 4.281,2.188 1.229,0.333 10 false Skid Control ECU 3.26,2.948 4.01,3.281 0.75,0.333 10 false G Sensor 3.188,3.542 4.021,3.875 0.833,0.333 10 false Motor Relay 3.115,4.188 4.156,4.521 1.042,0.333 10 false Yawrate Sensor 5.01,0.313 6.813,1 1.802,0.688 10 false Master Cylinder Cut Solenoid Valve (2) 5,1.917 6.802,2.531 1.802,0.615 10 false Pressure Holding Solenoid Valve (4) 5.094,4.031 6.844,4.698 1.75,0.667 10 false Master Cylinder Pressure Sensor 5.344,4.865 7.042,5.198 1.698,0.333 10 false Brake Actuator Assembly 5.042,5.281 6.958,5.615 1.917,0.333 10 false Combination Meter Assembly 5.229,5.781 6.698,6.125 1.469,0.344 10 false Brake Warning Light 5.354,6.167 6.802,6.5 1.448,0.333 10 false ABS Warning Light 5.188,6.583 6.823,6.927 1.635,0.344 10 false TRC OFF Indicator Light 5.177,6.979 6.802,7.323 1.625,0.344 10 false VSC OFF Indicator Light 5.354,7.365 6.615,7.698 1.26,0.333 10 false Slip Indicator Light 5.188,7.771 6.74,8.125 1.552,0.354 10 false TRACK Indicator Light 4.979,2.729 6.833,3.396 1.854,0.667 10 false Pressure Reduction Solenoid Valve (4) 5.031,1.115 6.813,1.802 1.781,0.688 10 false Reservoir Cut Solenoid Valve (2) 5.458,3.552 6.479,3.906 1.021,0.354 10 false Pump Motor

X108417E02
3.104,0.698 2.74,0.302 2.74,0.302 2.563,0.302 true 0.948,2.344 0.708,2.031 0.708,2.031 0.563,2.031 true 1.969,2.344 2.479,2.021 2.479,2.021 2.615,2.021 true 5.135,2.333 4.583,2.01 4.583,2.01 4.448,2.01 true 6.156,2.344 6.427,1.969 6.427,1.969 6.563,1.969 true 5.885,5.219 6.417,4.844 6.417,4.844 6.563,4.844 true 5.875,3.969 5.469,4.375 5.469,4.375 5.344,4.375 true 4.729,3.979 5.115,3.802 5.115,3.802 5.208,3.802 true 2.365,3.969 1.969,4.375 1.969,4.375 1.844,4.375 true 1.24,3.969 1.625,3.792 1.625,3.792 1.708,3.792 true 4.74,5.219 4.938,5.021 4.938,5.021 5.031,5.021 true 1.219,5.198 0.688,4.823 0.688,4.823 0.542,4.823 true 2.365,5.208 2.167,5.01 2.167,5.01 2.073,5.01 true 3.208,4.958 3.333,5.063 3.333,5.063 3.333,5.635 true 3.885,4.969 3.771,5.073 3.771,5.073 3.771,5.646 true 3.156,6.563 3.156,7.042 true 3.948,6.563 3.948,7.042 true 5.573,1.635 5.354,1.635 true 5.177,1.521 5.354,1.729 0.177,0.208 10 false *3 2.385,0.198 2.563,0.417 0.177,0.219 10 false *1 0.094,1.385 0.323,1.656 0.229,0.271 10 false *2 0.885,2.948 1.146,3.219 0.26,0.271 10 false (1) 1.865,2.948 2.094,3.208 0.229,0.26 10 false (2) 1.125,4.552 1.427,4.792 0.302,0.24 10 false (5) 2.292,4.552 2.583,4.792 0.292,0.24 10 false (6) 1.167,5.792 1.469,6.042 0.302,0.25 10 false (9) 2.271,5.792 2.594,6.042 0.323,0.25 10 false (10) 0.354,1.927 0.615,2.198 0.26,0.271 10 false (A) 2.656,1.917 2.958,2.167 0.302,0.25 10 false (B) 5.063,2.948 5.365,3.208 0.302,0.26 10 false (3) 6.073,2.958 6.365,3.219 0.292,0.26 10 false (4) 4.656,4.552 4.917,4.813 0.26,0.26 10 false (7) 5.802,4.552 6.052,4.802 0.25,0.25 10 false (8) 4.615,5.781 4.969,6.042 0.354,0.26 10 false (11) 5.76,5.781 6.073,6.021 0.313,0.24 10 false (12) 4.635,7.385 4.885,7.667 0.25,0.281 10 false *8 3.115,7.042 3.344,7.271 0.229,0.229 10 false *5 3.896,7.031 4.125,7.25 0.229,0.219 10 false *5 3.698,5.646 3.927,5.906 0.229,0.26 10 false *4 3.281,5.625 3.51,5.865 0.229,0.24 10 false *4 5.833,7.385 6.104,7.656 0.271,0.271 10 false *9 1.115,7.385 1.375,7.635 0.26,0.25 10 false *6 2.302,7.385 2.552,7.656 0.25,0.271 10 false *7 4.219,1.906 4.458,2.156 0.24,0.25 10 false (C) 6.604,1.865 6.854,2.125 0.25,0.26 10 false (D) 6.604,4.74 6.854,5.01 0.25,0.271 10 false (L) 5.125,4.26 5.354,4.531 0.229,0.271 10 false (H) 5.25,3.708 5.51,3.979 0.26,0.271 10 false (G) 1.625,4.229 1.865,4.5 0.24,0.271 10 false (F) 1.75,3.708 2.031,3.948 0.281,0.24 10 false (E) 5.073,4.917 5.333,5.188 0.26,0.271 10 false (K) 1.896,4.917 2.146,5.198 0.25,0.281 10 false (J) 0.385,4.719 0.594,4.99 0.208,0.271 10 false (I)

Text in Illustration (TRC Operation:)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Rear Brake Caliper (Right Side)
*7 Front Brake Caliper (Left Side) *8 Front Brake Caliper (Right Side)
*9 Rear Brake Caliper (Left Side) - -


ii.

Each valve operates as shown below:

Item Port TRC Not Activated TRC Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON* ON* ON*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open) ON (Open) ON (Open)
Front Brakes Pressure Holding Solenoid Valve (6), (7) (F), (G) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (10), (11) (J), (K) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure - - - - - -
Rear Brakes Pressure Holding Solenoid Valve (5), (8) (E), (H) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (9), (12) (I), (L) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Brake Wheel Cylinder Pressure - - - Increased Held Reduced
Pump OFF ON ON ON

HINT:

*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.




d.

VSC

i.

The VSC, by way of solenoid valves, controls the fluid pressure generated by the pump and applies it to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes. As a result, the tendency to front wheel skid or rear wheel skid is controlled.

X133919E02
0.708,1.083 2,1.417 1.292,0.333 10 false Speed Sensor (4) 0.51,3.156 1.854,3.469 1.344,0.313 10 false Pattern Select Switch 0.771,3.667 1.708,3.979 0.938,0.313 10 false TRACK Switch 0.708,4.188 1.844,4.5 1.135,0.313 10 false VSC OFF Switch 0.708,5.302 1.833,5.615 1.125,0.313 10 false Steering Sensor 1.052,6.51 1.458,6.906 0.406,0.396 10 false ECM 0.417,7.594 2.063,8.208 1.646,0.615 10 false Transmission Control ECU Assembly* 3.167,0.531 4.135,0.885 0.969,0.354 10 false Solenoid Relay 3.063,2.24 4.24,2.656 1.177,0.417 10 false Skid Control ECU 3.333,3 3.979,3.354 0.646,0.354 10 false G Sensor 3.26,3.594 4.052,3.927 0.792,0.333 10 false Motor Relay 3.156,4.26 4.146,4.604 0.99,0.344 10 false Yawrate Sensor 3.75,7.688 4.604,8.125 0.854,0.438 10 false CAN (V Bus) 5.031,0.385 6.844,1.01 1.813,0.625 10 false Master Cylinder Cut Solenoid Valve (2) 5.104,2 6.813,2.625 1.708,0.625 10 false Pressure Holding Solenoid Valve (4) 5.063,2.781 6.823,3.406 1.76,0.625 10 false Pressure Reduction Solenoid Valve (4) 5.552,3.583 6.427,3.927 0.875,0.344 10 false Pump Motor 5.177,4.063 6.771,4.708 1.594,0.646 10 false Master Cylinder Pressure Sensor 5.219,4.927 6.875,5.229 1.656,0.302 10 false Brake Actuator Assembly 5.063,5.323 6.927,5.635 1.865,0.313 10 false Combination Meter Assembly 5.313,5.823 6.667,6.146 1.354,0.323 10 false Brake Warning Light 5.354,6.229 6.594,6.542 1.24,0.313 10 false ABS Warning Light 5.198,6.615 6.813,6.958 1.615,0.344 10 false TRC OFF Indicator Light 5.219,7.021 6.781,7.333 1.563,0.313 10 false VSC OFF Indicator Light 5.354,7.406 6.563,7.729 1.208,0.323 10 false Slip Indicator Light 5.281,7.802 6.677,8.146 1.396,0.344 10 false TRACK Indicator Light 0.469,8.438 1.698,8.813 1.229,0.375 10 false *: Models with A/T 5.24,1.167 6.635,1.813 1.396,0.646 10 false Reservoir Cut Solenoid Valve (2)


ii.

During front wheel skid restraining control, the brake for the right rear wheel on the inside of the turn will be applied. Brakes for all wheels may also be activated if necessary. The diagram below indicates hydraulic pressure pathways in pressure increase mode for controlling front wheel skid when the vehicle makes a right-hand turn. In other modes, the pressure holding valve and pressure reduction valve may be turned on or off as required by ABS and EBD activation patterns.

X108419E02
3.104,0.729 2.74,0.333 2.74,0.333 2.563,0.333 true 0.948,2.385 0.708,2.073 0.708,2.073 0.563,2.073 true 1.969,2.396 2.479,2.073 2.479,2.073 2.615,2.073 true 5.146,2.396 4.594,2.073 4.594,2.073 4.458,2.073 true 6.146,2.385 6.417,2.01 6.417,2.01 6.552,2.01 true 5.896,5.271 6.427,4.896 6.427,4.896 6.573,4.896 true 5.865,4.021 5.458,4.427 5.458,4.427 5.333,4.427 true 4.74,4.031 5.125,3.854 5.125,3.854 5.219,3.854 true 2.375,4.021 1.979,4.427 1.979,4.427 1.854,4.427 true 1.25,4 1.635,3.823 1.635,3.823 1.719,3.823 true 4.729,5.26 4.927,5.063 4.927,5.063 5.021,5.063 true 1.208,5.271 0.677,4.896 0.677,4.896 0.531,4.896 true 2.365,5.26 2.167,5.063 2.167,5.063 2.073,5.063 true 3.229,4.99 3.313,5.094 3.313,5.094 3.313,5.667 true 3.885,5 3.771,5.104 3.771,5.104 3.771,5.677 true 3.156,6.625 3.156,7.104 true 3.948,6.625 3.948,7.104 true 5.573,1.677 5.354,1.677 true 5.188,1.552 5.365,1.781 0.177,0.229 10 false *3 2.396,0.219 2.573,0.438 0.177,0.219 10 false *1 0.094,1.448 0.323,1.667 0.229,0.219 10 false *2 0.885,2.99 1.125,3.229 0.24,0.24 10 false (1) 1.865,2.99 2.115,3.25 0.25,0.26 10 false (2) 1.125,4.594 1.396,4.854 0.271,0.26 10 false (5) 2.292,4.594 2.594,4.833 0.302,0.24 10 false (6) 1.146,5.823 1.396,6.083 0.25,0.26 10 false (9) 2.271,5.823 2.563,6.073 0.292,0.25 10 false (10) 0.333,1.948 0.583,2.229 0.25,0.281 10 false (A) 2.656,1.969 2.979,2.24 0.323,0.271 10 false (B) 5.063,2.99 5.302,3.229 0.24,0.24 10 false (3) 6.073,2.99 6.344,3.229 0.271,0.24 10 false (4) 4.656,4.594 4.896,4.844 0.24,0.25 10 false (7) 5.802,4.594 6.094,4.844 0.292,0.25 10 false (8) 4.615,5.823 4.917,6.073 0.302,0.25 10 false (11) 5.76,5.823 6.104,6.115 0.344,0.292 10 false (12) 4.635,7.438 4.844,7.698 0.208,0.26 10 false *8 3.104,7.094 3.313,7.323 0.208,0.229 10 false *5 3.896,7.104 4.104,7.333 0.208,0.229 10 false *5 3.688,5.677 3.948,5.917 0.26,0.24 10 false *4 3.271,5.667 3.49,5.896 0.219,0.229 10 false *4 5.833,7.438 6.052,7.677 0.219,0.24 10 false *9 1.115,7.438 1.365,7.698 0.25,0.26 10 false *6 2.302,7.438 2.521,7.677 0.219,0.24 10 false *7 4.24,1.969 4.5,2.177 0.26,0.208 10 false (C) 6.594,1.906 6.854,2.156 0.26,0.25 10 false (D) 6.604,4.792 6.865,5.094 0.26,0.302 10 false (L) 5.115,4.302 5.375,4.552 0.26,0.25 10 false (H) 5.25,3.75 5.521,4 0.271,0.25 10 false (G) 1.635,4.313 1.865,4.583 0.229,0.271 10 false (F) 1.75,3.729 2.01,3.969 0.26,0.24 10 false (E) 5.063,4.969 5.323,5.229 0.26,0.26 10 false (K) 1.896,4.958 2.115,5.198 0.219,0.24 10 false (J) 0.375,4.802 0.573,5.073 0.198,0.271 10 false (I)

Text in Illustration (VSC Operation (Front Wheel Skid Restraining):)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Rear Brake Caliper (Right Side)
*7 Front Brake Caliper (Left Side) *8 Front Brake Caliper (Right Side)
*9 Rear Brake Caliper (Left Side) - -


iii.

Each valve operates as shown below:

Item Port VSC Not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valve (1) (A) OFF (Open) ON* ON (Closed) ON*
(4) (D) OFF (Open) OFF (Open) OFF (Open) OFF (Open)
Reservoir Cut Solenoid Valve (2) (B) OFF (Closed) ON (Open) ON (Open) ON (Open)
(3) (C) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Front Brakes Pressure Holding Solenoid Valve (6) (F) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
(7) (G) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (10) (J) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
(11) (K) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure Right - - - Increased Held Reduced
Left - - - - - -
Rear Brakes Pressure Holding Solenoid Valve (5) (E) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
(8) (H) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (9) (I) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
(12) (L) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure Right - - - Increased Held Reduced
Left - - - - - -
Pump OFF ON ON ON

HINT:

*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.



iv.

During rear wheel skid restraining control, the brake for the front wheel on the outside of the turn will be applied. The diagram below indicates hydraulic pressure pathways in pressure increase mode for controlling rear wheel skid when the vehicle makes a right-hand turn. In other modes, the pressure holding valve and pressure reduction valve may be turned on or off as required by ABS and EBD activation patterns.

X108742E02
3.104,0.677 2.74,0.281 2.74,0.281 2.563,0.281 true 0.948,2.333 0.708,2.021 0.708,2.021 0.563,2.021 true 1.969,2.333 2.479,2.021 2.479,2.021 2.615,2.021 true 5.135,2.333 4.583,2.01 4.583,2.01 4.448,2.01 true 6.146,2.333 6.417,1.969 6.417,1.969 6.552,1.969 true 5.885,5.198 6.417,4.823 6.417,4.823 6.563,4.823 true 5.865,3.969 5.458,4.385 5.458,4.385 5.333,4.385 true 4.729,3.958 5.115,3.781 5.115,3.781 5.208,3.781 true 2.375,3.958 1.979,4.375 1.979,4.375 1.854,4.375 true 1.229,3.958 1.615,3.781 1.615,3.781 1.698,3.781 true 4.74,5.198 4.927,5.021 4.927,5.021 5.021,5.021 true 1.208,5.219 0.677,4.844 0.677,4.844 0.531,4.844 true 2.365,5.198 2.167,5.01 2.167,5.01 2.073,5.01 true 3.219,4.927 3.313,5.042 3.313,5.042 3.313,5.604 true 3.885,4.948 3.771,5.063 3.771,5.063 3.771,5.625 true 3.156,6.573 3.156,7.052 true 3.948,6.573 3.948,7.052 true 5.573,1.635 5.354,1.635 true 5.177,1.521 5.365,1.74 0.188,0.219 10 false *3 2.396,0.177 2.563,0.406 0.167,0.229 10 false *1 0.094,1.406 0.292,1.667 0.198,0.26 10 false *2 0.885,2.938 1.125,3.219 0.24,0.281 10 false (1) 1.865,2.938 2.146,3.229 0.281,0.292 10 false (2) 1.125,4.542 1.396,4.802 0.271,0.26 10 false (5) 2.292,4.542 2.531,4.781 0.24,0.24 10 false (6) 1.146,5.771 1.438,6.031 0.292,0.26 10 false (9) 2.271,5.771 2.604,6.01 0.333,0.24 10 false (10) 0.344,1.906 0.594,2.167 0.25,0.26 10 false (A) 2.667,1.917 2.969,2.219 0.302,0.302 10 false (B) 5.063,2.938 5.302,3.188 0.24,0.25 10 false (3) 6.073,2.948 6.333,3.229 0.26,0.281 10 false (4) 4.656,4.542 4.938,4.792 0.281,0.25 10 false (7) 5.802,4.542 6.083,4.781 0.281,0.24 10 false (8) 4.615,5.771 4.917,6 0.302,0.229 10 false (11) 5.76,5.771 6.063,6.021 0.302,0.25 10 false (12) 4.635,7.375 4.865,7.635 0.229,0.26 10 false *8 3.094,7.042 3.344,7.292 0.25,0.25 10 false *5 3.896,7.052 4.104,7.281 0.208,0.229 10 false *5 3.688,5.625 3.917,5.896 0.229,0.271 10 false *4 3.271,5.604 3.479,5.823 0.208,0.219 10 false *4 5.833,7.385 6.073,7.635 0.24,0.25 10 false *9 1.115,7.375 1.344,7.625 0.229,0.25 10 false *6 2.302,7.375 2.573,7.635 0.271,0.26 10 false *7 4.229,1.906 4.479,2.146 0.25,0.24 10 false (C) 6.594,1.865 6.833,2.135 0.24,0.271 10 false (D) 6.594,4.708 6.833,4.979 0.24,0.271 10 false (L) 5.125,4.281 5.385,4.531 0.26,0.25 10 false (H) 5.24,3.677 5.5,3.927 0.26,0.25 10 false (G) 1.635,4.25 1.875,4.5 0.24,0.25 10 false (F) 1.75,3.698 2.01,3.948 0.26,0.25 10 false (E) 5.063,4.917 5.313,5.167 0.25,0.25 10 false (K) 1.896,4.917 2.135,5.198 0.24,0.281 10 false (J) 0.375,4.74 0.594,4.979 0.219,0.24 10 false (I)

Text in Illustration (VSC Operation (Rear Wheel Skid Restraining):)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Rear Brake Caliper (Right Side)
*7 Front Brake Caliper (Left Side) *8 Front Brake Caliper (Right Side)
*9 Rear Brake Caliper (Left Side) - -


v.

Each valve operates as shown below:

Item Port VSC Not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON* ON (Closed) ON*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open) ON (Open) ON (Open)
Front Brakes Pressure Holding Solenoid Valve (6) (F) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
(7) (G) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (10) (J) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
(11) (K) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure Right - - - - - -
Left - - - Increased Held Reduced
Rear Brakes Pressure Holding Solenoid Valve (5) (E) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
(8) (H) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve (9) (I) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
(12) (L) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure Right - - - - - -
Left - - - - - -
Pump OFF ON ON ON

HINT:

*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.




e.

Hill-start Assist Control

i.

Hill-start Assist Control controls the brakes* by maintaining the master cylinder fluid pressure produced by depressing the brake pedal.

HINT:

*: Approximately 2 seconds at the maximum.



ii.

During Hill-start Assist Control, the hill-start assist indicator light blinks.

X133931E01
0.615,1.448 1.771,1.76 1.156,0.313 10 false Speed Sensor (4) 3.156,0.875 4.135,1.198 0.979,0.323 10 false Solenoid Relay 5.052,0.76 6.865,1.365 1.813,0.604 10 false Master Cylinder Cut Solenoid Valve (2) 0.406,5.188 2.083,5.76 1.677,0.573 10 false Main Body ECU (Network Gateway ECU) 0.323,6.229 2.344,6.552 2.021,0.323 10 false Parking Brake Switch Assembly 0.365,3.656 2.125,4.177 1.76,0.521 10 false Stop Light Switch Assembly 1.104,7.115 1.563,7.438 0.458,0.323 10 false ECM 3.104,2.448 4.208,2.927 1.104,0.479 10 false Skid Control ECU 3.344,3.344 3.99,3.542 0.646,0.198 10 false G Sensor 3.271,3.938 4.052,4.281 0.781,0.344 10 false Motor Relay 3.125,4.604 4.156,4.938 1.031,0.333 10 false Yawrate Sensor 3.354,7.292 4.198,7.74 0.844,0.448 10 false CAN (V Bus) 5.198,1.531 6.615,2.146 1.417,0.615 10 false Reservoir Cut Solenoid Valve (2) 5.135,2.354 6.771,2.969 1.635,0.615 10 false Pressure Holding Solenoid Valve (4) 5.052,3.156 6.854,3.74 1.802,0.583 10 false Pressure Reduction Solenoid Valve (4) 5.125,4.448 6.698,5.042 1.573,0.594 10 false Master Cylinder Pressure Sensor 5.531,3.948 6.354,4.25 0.823,0.302 10 false Pump Motor 5.198,5.271 6.823,5.719 1.625,0.448 10 false Brake Actuator Assembly 5.063,5.792 6.979,6.115 1.917,0.323 10 false Combination Meter Assembly 5.292,6.302 6.604,6.635 1.313,0.333 10 false Brake Warning Light 5.313,6.708 6.542,7.042 1.229,0.333 10 false ABS Warning Light 5.313,7.083 6.49,7.417 1.177,0.333 10 false Slip Indicator Light 5.208,7.542 6.792,8.104 1.583,0.563 10 false Hill-start Assist Indicator Light 5.708,8.177 6.208,8.49 0.5,0.313 10 false Buzzer 0.667,2.854 2.021,3.198 1.354,0.344 10 false VSC OFF Switch 0.25,2.146 2.313,2.625 2.063,0.479 10 false Pattern Select Switch Assembly

X133930E02
2.552,0.396 2.75,0.396 2.75,0.396 3.188,0.979 true 5.667,1.917 5.365,1.917 true 0.635,2.125 0.708,2.125 0.708,2.125 1.031,2.521 true 2.698,2.229 2.604,2.229 2.604,2.229 2.031,2.521 true 4.542,2.25 4.646,2.25 4.646,2.25 5.229,2.521 true 6.615,2.167 6.521,2.167 6.521,2.167 6.219,2.49 true 1.781,4.083 1.698,4.083 1.698,4.083 1.292,4.219 true 1.958,4.385 2.042,4.385 2.042,4.385 2.448,4.177 true 5.281,4.115 5.188,4.115 5.188,4.115 4.792,4.25 true 5.458,4.469 5.542,4.469 5.542,4.469 5.948,4.135 true 0.625,4.99 0.698,4.99 0.698,4.99 1.281,5.448 true 2.063,4.979 2.135,4.979 2.135,4.979 2.448,5.448 true 5.177,5.021 5.115,5.021 5.115,5.021 4.781,5.427 true 6.635,5 6.563,5 6.563,5 5.948,5.448 true 3.292,5.208 3.354,5.281 3.354,5.281 3.354,6.219 true 3.958,5.208 3.885,5.281 3.885,5.281 3.885,6.219 true 3.229,6.792 3.229,7.271 true 4.021,6.792 4.021,7.271 true 2.354,0.302 2.552,0.51 0.198,0.208 10 false *1 0.146,1.677 0.344,1.885 0.198,0.208 10 false *2 5.146,1.854 5.344,2.021 0.198,0.167 10 false *3 0.417,2 0.656,2.208 0.24,0.208 10 false (A) 2.74,2.104 2.979,2.313 0.24,0.208 10 false (B) 0.969,3.292 1.208,3.5 0.24,0.208 10 false (1) 1.948,3.271 2.188,3.479 0.24,0.208 10 false (2) 1.229,4.844 1.469,5.052 0.24,0.208 10 false (5) 2.385,4.875 2.625,5.083 0.24,0.208 10 false (6) 1.208,6.125 1.448,6.333 0.24,0.208 10 false (9) 2.344,6.104 2.625,6.313 0.281,0.208 10 false (10) 4.698,6.094 5,6.302 0.302,0.208 10 false (11) 5.854,6.115 6.135,6.323 0.281,0.208 10 false (12) 4.729,4.875 4.969,5.083 0.24,0.208 10 false (7) 5.906,4.896 6.146,5.104 0.24,0.208 10 false (8) 5.146,3.302 5.385,3.51 0.24,0.208 10 false (3) 6.146,3.313 6.385,3.521 0.24,0.208 10 false (4) 4.302,2.167 4.542,2.375 0.24,0.208 10 false (C) 6.646,2.073 6.885,2.281 0.24,0.208 10 false (D) 1.813,3.99 2.052,4.198 0.24,0.208 10 false (E) 1.75,4.271 1.99,4.479 0.24,0.208 10 false (F) 5.313,4.01 5.552,4.219 0.24,0.208 10 false (G) 5.229,4.365 5.469,4.573 0.24,0.208 10 false (H) 0.479,4.885 0.635,5.146 0.156,0.26 10 false (I) 1.885,4.865 2.125,5.073 0.24,0.208 10 false (J) 5.198,4.906 5.438,5.115 0.24,0.208 10 false (K) 6.667,4.885 6.906,5.094 0.24,0.208 10 false (L) 3.281,6.24 3.479,6.448 0.198,0.208 10 false *4 3.802,6.25 3.979,6.458 0.177,0.208 10 false *4 3.156,7.302 3.354,7.51 0.198,0.208 10 false *5 3.938,7.302 4.135,7.51 0.198,0.208 10 false *5 1.219,7.688 1.417,7.896 0.198,0.208 10 false *6 2.375,7.688 2.573,7.896 0.198,0.208 10 false *7 4.729,7.688 4.927,7.896 0.198,0.208 10 false *8 5.875,7.688 6.073,7.896 0.198,0.208 10 false *9

Text in Illustration (Hill-start Assist Control Operation:)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Rear Brake Caliper (Right Side)
*7 Front Brake Caliper (Left Side) *8 Front Brake Caliper (Right Side)
*9 Rear Brake Caliper (Left Side) - -


iii.

Each valve operates as shown below:

Item Port Hill-start Assist Control Operation
Not Activated Pressure Holding Mode Pressure Reduction Mode
Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON* ON*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) OFF (Closed) OFF (Closed)
Front Brake Pressure Holding Solenoid Valve (6) (F) OFF (Open) OFF (Open) OFF (Open)
(7) (G) OFF (Open) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valve (10) (J) OFF (Closed) OFF (Closed) OFF (Closed)
(11) (K) OFF (Closed) OFF (Closed) OFF (Closed)
Wheel Cylinder Pressure Right - - - Holds Reduces
Left - - - Holds Reduces
Rear Brake Pressure Holding Solenoid Valve (5) (E) OFF (Open) OFF (Open) OFF (Open)
(8) (H) OFF (Open) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valve (9) (I) OFF (Closed) OFF (Closed) OFF (Closed)
(12) (L) OFF (Closed) OFF (Closed) OFF (Closed)
Wheel Cylinder Pressure Right - - - Holds Reduces
Left - - - Holds Reduces
Pump OFF ON ON

HINT:

*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.





FAIL-SAFE


a.

If a failure occurs in the skid control ECU, sensors, or brake actuator assembly, the system continues performing brake control by excluding the failed area and using only the areas that are operating normally.



DIAGNOSIS


a.

If the skid control ECU detects a malfunction in the brake control system, the warning lights or indicator light illuminate. At the same time, a Diagnostic Trouble Code (DTC) is stored in the memory of the skid control ECU.


b.

This system has a sensor signal check (test mode) function.


c.

For details of DTCs and the check function, refer to the Repair Manual.