Home › Power Source / Network › NETWORKING › MULTIPLEX COMMUNICATION SYSTEM › 2012.03–2019.03
NM2090E _57 Power Source / Network _060645 NETWORKING _0297343 MULTIPLEX COMMUNICATION SYSTEM UN GENERAL/CONTROL/DETAILS F

NETWORKING  MULTIPLEX COMMUNICATION SYSTEM  GENERAL/CONTROL/DETAILS  GENERAL  


OUTLINE


a.

The multiplex communication system uses 2 communication protocols (CAN and LIN) to achieve a streamlined wiring harness configuration.

Protocol Outline
CAN (Controller Area Network) The High Speed (HS)-CAN is used for the power train, chassis and body electrical systems.
LIN (Local Interconnect Network) LIN is used for local area networking, in which the system has a LIN bus for each respective body electrical system.


b.

Due to the introduction of the CAN communication system for the powertrain, chassis and body electrical systems, the wiring harness configuration has been streamlined.


c.

There is no direct communication between CAN and LIN networks because these multiplex communication systems are incompatible. CAN and LIN are separate networks. Because of this, some ECUs serve as gateways for the transfer of data, allowing communication between CAN and LIN networks.


d.

A customizable body electrical system is used, enabling some of the control functions of the ECUs to be set using the Grobal TechStream (GTS). For details, refer to the Repair Manual.

HINT:

Generally speaking, multiplex communication refers to the use of serial communication data that consists of bits and frames in order to exchange information among various ECUs. This allows for a reduction of the amount of wiring on the vehicle. A bit is the basic unit of communication that is used to represent the information. A bit is represented by binary values of "0" or "1". For CAN communication, a differential voltage drive is used to represent the binary values of "0" or "1". This "differential voltage drive" reduces the effects of electrical interference.


Y100125E46
0.302,0.365 4.094,0.656 3.792,0.292 12 false Conceptual Drawing for Multiplex Communication: 0.229,1.667 1.656,2.188 1.427,0.521 10 false Serial Communication Data 3.51,1.135 4.219,1.448 0.708,0.313 10 false Frame 2.208,2.448 2.917,2.76 0.708,0.313 10 false Header 4.646,2.448 5.719,2.76 1.073,0.313 10 false End Message 3.521,1.833 4.229,2.146 0.708,0.313 10 false Data 1.802,1.729 2.125,2.042 0.323,0.313 10 false 1 1.802,2.115 2.125,2.427 0.323,0.313 10 false 0 0.313,4.938 1.031,5.458 0.719,0.521 10 false Battery 1.813,3.823 2.427,4.344 0.615,0.521 10 false Switch 2.604,4.927 3.01,5.521 0.406,0.594 10 false ECU 3.313,4.188 3.646,4.552 0.333,0.365 10 false ON 3.823,4.198 4.156,4.563 0.333,0.365 10 false ON 3.542,4.958 3.875,5.323 0.333,0.365 10 false OFF 6.167,4.365 6.677,4.635 0.51,0.271 10 false Light 6.167,4.781 6.75,5.052 0.583,0.271 10 false Motor 6.167,5.198 6.823,5.469 0.656,0.271 10 false Heater 6.177,5.635 6.99,5.906 0.813,0.271 10 false Solenoid 2.875,5.906 4.667,6.323 1.792,0.417 10 false Single Wire Voltage Drive 0.313,6.365 4.656,6.833 4.344,0.469 12 false Conceptual Drawing for CAN Communication: 4.49,4.969 4.885,5.573 0.396,0.604 10 false ECU 2.167,7.667 2.583,8.271 0.417,0.604 10 false ECU 4.896,7.74 5.302,8.188 0.406,0.448 10 false ECU 2.99,9.188 4.781,9.594 1.792,0.406 10 false Differential Voltage Drive 3.146,8.177 4.542,8.552 1.396,0.375 10 false Twisted-pair Wire 2.667,7.604 3.135,7.958 0.469,0.354 10 false + 4.615,7.615 5.083,7.969 0.469,0.354 10 false + 2.677,8.083 3.146,8.438 0.469,0.354 10 false - 4.625,8.104 5.094,8.458 0.469,0.354 10 false -


e.

Differences between CAN and LIN

i.

Protocols, which are the rules for establishing data communication, differ between CAN and LIN. If the ECUs in the networks use different data frameworks such as communication speed, communication wire or signals, they will be unable to understand each other. Therefore, protocols (rules) must be established among them.


ii.

Compared to LIN, and CAN features high-speed data transmission. Therefore, CAN is able to transmit larger amounts of data faster than other protocols. This feature makes it possible to transmit data accurately for the power train and chassis control systems. These systems require large amounts of data to be transmitted in short periods of time.

Protocol CAN LIN
HS-CAN
Communication Speed 500 kbps*1 9.6 (Entry and Start System)*2, 19.2 (Power Window Control System)kbps*1
Communication Wire Twisted-pair Wire AV Single Wire
Drive Type Differential Voltage Drive Single Wire Voltage Drive
Data Length 1-8 Byte (Variable) 4, 6, 8 Byte (Variable)

*1: "bps" is an abbreviation for "Bits Per Second", indicating the number of bits that can be transmitted per second.

*2: Models with entry and start system


iii.

A twisted-pair of wires is used for CAN communication. A single Automobile Vinyl (AV) wire is used for LIN communication.

Communication Wire Outline
Twisted-pair Wire
Y188976

This communication wire is a pair of twisted wires. Communication is driven by applying different voltages to the 2 lines in order to send a single signal. This system, which is called a "Differential Voltage Drive", reduces noise.
AV Single Wire
Y188977

This is a lightweight single communication wire that consists of a single core line surrounded by insulation. Voltage is applied to this line in order to drive communication, and this system is called a "Single Wire Voltage Drive".
Shielded Twisted-pair Wire
Y189723

This communication wire is a shielded pair of twisted wires. Communication is driven by applying different voltages to the 2 lines in order to send a single signal. This system, which is called a "Differential Voltage Drive", reduces noise.