Home › General › INTRODUCTION › HOW TO USE THIS MANUAL
RM2090E _V1 General _060661 INTRODUCTION _0297366 HOW TO USE THIS MANUAL F

INTRODUCTION  HOW TO USE THIS MANUAL  GENERAL INFORMATION  


GENERAL DESCRIPTION


a.

This manual is written in accordance with SAE J2008.


b.

Repair operations can be separated mainly into the following 3 processes:

i.

Diagnosis


ii.

Removing/Installing, Replacing, Disassembling/Reassembling, Checking and Adjusting


iii.

Final Inspection



c.

The following procedure is omitted from this manual. However, this procedure must be performed.

i.

Use a jack or lift to perform operations.


ii.

Clean all removed parts.


iii.

Perform a visual check before and after performing any work.




INDEX


a.

An alphabetical INDEX section is provided at the end of the manual as a reference to help find the item to be repaired.



PREPARATION


a.

Use of Special Service Tools (SST) and Special Service Materials (SSM) may be required, depending on the repair procedure. Be sure to use SST and SSM when they are required and follow the work procedure properly. A list of SST and SSM is in the "Preparation" section of this manual.



REPAIR PROCEDURES


a.

A component illustration is placed under the title where necessary.


b.

Non-reusable parts, grease application areas, precoated parts and torque specifications are noted in the component illustrations.

The following illustration is an example.


D224268E01
0.26,2.167 0.938,2.365 0.677,0.198 2.958,1.552 3.635,1.75 0.677,0.198 0.146,3.073 1.406,3.281 1.26,0.208 1.49,0.208 1.688,0.208 false 0.865,0.583 1.063,0.583 false 1.49,0.854 1.719,0.646 1.719,0.646 1.917,0.646 false 0.781,1.479 0.958,1.344 false 1.76,1.833 2.073,1.188 2.073,1.188 2.271,1.188 false 1.198,2.042 1.073,2.271 1.073,2.271 0.948,2.271 false 2.76,1.646 2.958,1.646 false 0.948,2.635 1.146,2.635 false 3.521,2.094 3.375,2.656 3.375,2.656 3.198,2.656 false 4.021,2.177 4.146,1.896 false 4.563,1.625 4.25,1.229 4.25,1.229 4.427,1.229 false 5.365,1.344 4.667,0.667 4.667,0.667 4.844,0.667 false 5.698,1.083 5.469,0.458 5.469,0.458 5.74,0.458 false 6.479,1.281 6.271,0.771 6.271,0.771 6.448,0.771 false 6.083,1.458 6.188,1.688 6.188,1.688 6.51,1.688 false 5.792,1.49 5.938,2.083 5.938,2.083 6.167,2.083 false 5.177,1.74 5.313,2.271 5.313,2.271 5.542,2.271 false 4.885,1.781 5.115,2.583 5.115,2.583 5.344,2.583 false 0.167,0.083 0.76,0.281 0.594,0.198 10 false Example: 1.729,0.115 2.323,0.313 0.594,0.198 10 false Filter Cap 0.469,0.5 0.823,0.677 0.354,0.177 10 false Float 1.969,0.563 2.906,0.75 0.938,0.188 10 false Reservoir Tank 0.094,1.5 1.208,1.688 1.115,0.188 10 false Slotted Spring Pin 2.302,1.083 2.448,1.271 0.146,0.188 10 false ● 4.469,1.135 4.969,1.323 0.5,0.188 10 false Washer 3.01,1.573 3.604,1.729 0.594,0.156 8 false 12 (120, 9) 0.302,2.188 0.979,2.344 0.677,0.156 8 false 15 (155, 11) 0.396,2.542 0.927,2.719 0.531,0.177 10 false Cylinder 2.76,2.594 3.188,2.771 0.427,0.177 10 false Piston 3.833,2.229 4.448,2.406 0.615,0.177 10 false Push Rod 2.438,1.094 3.031,1.281 0.594,0.188 10 false Grommet 4.885,0.573 5.031,0.76 0.146,0.188 10 false ● 5.01,0.583 5.49,0.771 0.479,0.188 10 false Gasket 5.823,0.365 6.458,0.552 0.635,0.188 10 false Clevis Pin 6.51,0.698 6.792,0.896 0.281,0.198 10 false Clip 6.583,1.635 6.948,1.823 0.365,0.188 10 false Clevis 6.219,2 6.792,2.198 0.573,0.198 10 false Lock Nut 5.594,2.198 5.938,2.375 0.344,0.177 10 false Boot 5.385,2.5 6.031,2.708 0.646,0.208 10 false Snap Ring 0.188,3.094 1.469,3.271 1.281,0.177 10 false N*m (kgf*cm, ft.*lbf) 0.177,3.427 0.323,3.615 0.146,0.188 10 false ● 0.354,3.438 1.458,3.615 1.104,0.177 10 false Non-reusable part 1.469,3.083 2.573,3.26 1.104,0.177 10 false : Specified torque


c.

Torque specifications, grease application areas and non-reusable parts are emphasized in the procedures.

HINT:

There are cases where such information can only be explained by using an illustration. In these cases, torque, oil and other information are described in the illustration.



d.

Only items with key points are described in the text. What to do and other details are explained using illustrations next to the text. Both the text and illustrations are accompanied by standard values and notices.

Illustration What to do and where to do it
Task heading What work will be performed
Explanation text
·

How to perform the task

·

Information such as specifications and warnings, which are written in boldface text




e.

Illustrations of similar vehicle models are sometimes used. In these cases, minor details may be different from the actual vehicle.


f.

Procedures are presented in a step-by-step format.



SERVICE SPECIFICATIONS


a.

Specifications are presented in boldface text throughout the manual. The specifications are also found in the "Service Specifications" section for reference.



TERM DEFINITIONS


CAUTION Possibility of injury to you or other people.
NOTICE Possibility of damage to components being repaired.
HINT Provides additional information to help you perform repairs.


INTERNATIONAL SYSTEM OF UNITS


a.

The units used in this manual comply with the International System of Units (SI UNIT) standard. Other units from the metric system and the English systems are also provided.

Example:


Torque:
30 N*m (310 kgf*cm, 22 ft.*lbf)