Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM › 2012.03–2016.06
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM U

FA20 ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


U146803E04
0.813,0.792 1.104,0.948 0.292,0.156 10 false A36 2.49,0.781 2.781,0.938 0.292,0.156 10 false A35 4.344,0.792 4.635,0.948 0.292,0.156 10 false A34 5.99,0.792 6.281,0.948 0.292,0.156 10 false A33

HINT:

The standard voltage between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of the terminals, and displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A33-1 (+B2) - A36-4 (E01) V - B-L Power source of ECM Ignition switch ON 12 to 14 V
A33-2 (BATT) - A36-4 (E01) W - B-L Battery(for measuring battery voltage and for ECM memory) Always 10 to 13 V
A33-3 (ST1-) - A36-4 (E01) BR-B - B-L Stop light switch Brake pedal depressed 11 to 14 V
Brake pedal released 0 to 1 V
A33-7 (STP) - A36-4 (E01)*1 R - B-L Stop light switch Brake pedal depressed 0 to 1 V
Brake pedal released 11 to 14 V
A33-8 (ACP) - A36-4 (E01)*5 G - B-L Airconditioner pressure sensor Ignition switch ON with A/C on 0 to 1 V
Idling with A/C off 12 to 14 V
A33-12 (THA) - A36-29 (E1) BR-G - Y-B Intake air temperature sensor
(built into mass air flow meter)
Ignition switch ON 0.3 to 4.6 V
A33-14 (STSW2) - A36-4 (E01)*3 BR - B-L Starter signal Ignition switch ON 0 to 1 V
Cranking 6 to 13 V
A33-15 (CLSW) - A36-4 (E01)*2 R-Y - B-L Clutch switch Ignition switch ON with clutch pedal depressed 0 to 1 V
Ignition switch ON with clutch pedal released 10 to 13 V
A33-16 (NSW) - A36-4 (E01) W-R - B-L*1
G-B - B-L*2
Neutral switch signal Ignition switch ON, shift lever in P or N*1
Ignition switch ON, shift lever in Neutral*2
0 to 1 V
Ignition switch ON, shift lever not in P or N*1
Ignition switch ON, shift lever not in Neutral*2
10 to 13 V
A33-17 (STSW) - A36-4 (E01)*3 G-W - B-L Starter signal from certification ECU (smart key ECU assembly*3) Ignition switch ON 0 to 1 V
Cranking Over 6 V
A33-17 (STSW2) - A36-4 (E01)*4 BR - B-L Starter signal Ignition switch ON 0 to 1 V
Cranking 6 to 13 V
A33-18 (CANL) - A36-4 (E01) B-P - B-L CAN communication line Ignition switch ON Pulse generation
(See waveform 1)
A33-19 (CANH) - A36-4 (E01) O - B-L CAN communication line Ignition switch ON Pulse generation
(See waveform 2)
A33-20 (HB) - A36-4 (E01)*10 G-Y - B-L BLOWER relay Ignition switch ON with blower fan switch on 0 to 1 V
Ignition switch ON with blower fan switch off 10 to 13 V
A33-22 (VG) - A33-29 (E2G) Y - B-G Mass air flow meter Idling with warm engine 0.9 to 4.5 V
A33-27 (IGSW) - A36-4 (E01) GR - B-L IG2 relay Ignition switch ON 10 to 13 V
A34-5 (HA1A) - A36-4 (E01) R-L - B-L Air fuel ratio sensor heater Idling with cold engine Pulse generation
(See waveform 3)
A34-6 (+B) - A36-4 (E01) V - B-L Power source of ECM Ignition switch ON 12 to 14 V
A34-9 (PR) - A36-29 (E1) V-B - Y-B Fuel pressure sensor Idling with warm engine 1.0 to 1.7 V
A34-11 (IJF1) - A36-4 (E01) R-Y - B-L Injector for direct injection confirmation signal Idling Pulse generation
(See waveform 4)
A34-13 (FPF) - A36-4 (E01) R-B - B-L High pressure side fuel pump (Spill valve) Idling Pulse generation
(See waveform 5)
A34-14 (EV1+) - A36-4 (E01) Y-BR - B-L Variable valve timing (VVT) sensor (Exhaust side (bank 1)) Idling with warm engine Pulse generation
(See waveform 6)
A34-15 (VV2+) - A36-4 (E01) Y-V - B-L Variable valve timing (VVT) sensor (Intake side (bank 2)) Idling with warm engine Pulse generation
(See waveform 7)
A34-16 (NE+) - A34-27 (NE-) W - B Crank position sensor Idling with warm engine Pulse generation
(See waveform 6 or 7)
A34-17 (KNK2) - A36-29 (E1) G - Y-B Knock sensor Ignition switch ON Approximately 2.5 V
A34-18 (A1A-) - A36-4 (E01) O - B-L Air fuel ratio sensor Ignition switch ON 2.4 to 2.7 V
A34-19 (A1A+) - A36-4 (E01) W - B-L Air fuel ratio sensor Ignition switch ON 2.8 to 3.2 V
A34-20 (PIM) - A36-29 (E1) BR-B - Y-B Intake manifold pressure sensor Idling with warm engine 1.1 to 2.0 V
A34-21 (OX1B) - A36-4 (E01) L-W - B-L Heated oxygen sensor Idling with warm engine 0 to 0.9 V
A34-25 (EV2+) - A36-4 (E01) BR-Y - B-L Variable valve timing (VVT) sensor (Exhaust side (bank 2)) Idling with warm engine Pulse generation
(See waveform 6)
A34-26 (VV1+) - A36-4 (E01) Y-P - B-L Variable valve timing (VVT) sensor (Intake side (bank 1)) Idling with warm engine Pulse generation
(See waveform 7)
A34-28 (KNK1) - A36-29 (E1) L - Y-B Knock sensor Ignition switch ON Approximately 2.5 V
A34-31 (IJF2) - A36-4 (E01) R-G - B-L Injector for direct injection confirmation signal Idling Pulse generation
(See waveform 4)
A34-32 (FPD) - A36-4 (E01) R-W - B-L High pressure side fuel pump (Spill valve) Idling Pulse generation
(See waveform 5)
A34-34 (VVE) - A36-4 (E01) G-B - B-L Ground Always Below 1 Ω
A35-1 (VPMP) - A36-4 (E01)*9 P-L - B-L Vent valve (built into canister pump module) Ignition switch ON 10 to 13 V
A35-5 (IREL) - A36-4 (E01) O-W - B-L INJ relay Idling 10 to 13 V
Ignition switch ON 0 to 1 V
A35-7 (+BM) - A36-4 (E01) L-R - B-L ETCS relay Ignition switch ON 10 to 13 V
A35-8 (MPMP) - A36-4 (E01)*9 O-L - B-L Leak detection pump (built into canister pump module)) Ignition switch ON 10 to 13 V
Leak detection pump ON 0 to 1 V
A35-10 (DI) - A36-4 (E01) R-B - B-L Fuel pump control (for fuel pump control malfunctioning detection) Ignition switch ON 10 to 12 V
A35-11 (FAN2) - A36-4 (E01)*5 R-Y - B-L FAN NO. 3 relay Ignition switch ON
Cooling fan not operated
10 to 13 V
Idling with A/C on or High engine coolant temperature Cooling fan operated 0 to 0.5 V
A35-11 (FAN1) - A36-4 (E01)*6 B-R - B-L FAN NO. 1 relay Ignition switch ON
Cooling fan not operated
10 to 13 V
High engine coolant temperature Cooling fan operated 0 to 0.5 V
A35-12 (FAN1) - A36-4 (E01)*5 B-R - B-L FAN NO. 2 relay Ignition switch ON 10 to 13 V
Idling with A/C on or High engine coolant temperature Cooling fan operated 0 to 0.5 V
A35-13 (SSHUT) - A36-4 (E01) LG - B-L EFI MAIN1 relay Ignition switch ON 0 to 1 V
A35-15 (TACH) - A36-4 (E01)*3 GR-R - B-L Engine speed Engine speed maintained at 1500 rpm Pulse generation
(See waveform 8)
A35-17 (MCR) - A36-4 (E01) R-L - B-L ETCS relay Ignition switch ON 0 to 1 V
A35-19 (FPC) - A36-4 (E01) G-R - B-L Fuel pump control Ignition switch ON Pulse generation
(See waveform 9)
A35-20 (PPMP) - A36-4 (E01)*9 O-B - B-L Canister pressure sensor (built into canister pump module) Ignition switch ON 1.5 to 4.0 V
A35-21 (VCPA) - A36-4 (E01) L-Y - B-L Power source of accelerator pedal position sensor Ignition switch ON 4.5 to 5.5 V
A35-22 (VCP2) - A36-4 (E01) G-B - B-L Power source of accelerator pedal position sensor Ignition switch ON 4.5 to 5.5 V
A35-23 (VPA) - A35-29 (EPA) W - L Accelerator pedal position sensor (for engine control) Ignition switch ON, Accelerator pedal fully released Approximately 0.7 V
Ignition switch ON, Accelerator pedal fully depressed Approximately 3.1 V
A35-26 (STA) - A36-4 (E01) B-W - B-L*7
B-L - B-L*8
ST relay Ignition switch ON 10 to 13 V
Cranking 0 to 1 V
A35-31 (VPA2) - A35-30 (EPA2) O - Y-B Accelerator pedal position sensor (for sensor malfunctioning detection) Ignition switch ON, Accelerator pedal fully released Approximately 0.7 V
Ignition switch ON, Accelerator pedal fully depressed Approximately 3.1 V
A35-32 (ACCR) - A36-4 (E01)*3 G-Y - B-L ACC relay signal sent to certification ECU Ignition switch ON 0 to 0.5 V
Cranking 12 to 14 V
A35-34 (STAR) - A36-4 (E01)*3 LG-R - B-L ST CUT relay Ignition switch ON 0 to 0.5 V
Cranking 8 to 13 V
A35-35 (AC) - A36-4 (E01)*5 L-O - B-L HEATER relay Idling with A/C on 0 to 0.5 V
Idling with A/C off 12 to 14 V
A36-1 (M-) - A36-4 (E01) SB - B-L Throttle actuator Idling with warm engine Pulse generation
(See waveform 10)
A36-2 (M+) - A36-4 (E01) G-Y - B-L Throttle actuator Idling with warm engine Pulse generation
(See waveform 10)
A36-5 (OE2) - A36-4 (E01) BR-L - B-L Camshaft timing oil control valve (OCV) (Exhaust side (bank 2)) Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(See waveform 11)
A36-6 (HT1B) - A36-4 (E01) R-B - B-L Heated oxygen sensor heater Ignition switch ON 11 to 14 V
Idling with cold engine Pulse generation
(See waveform 12)
A36-7 (OE1) - A36-4 (E01) R-W - B-L Camshaft timing oil control valve (OCV) (Exhaust side (bank 1)) Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(See waveform 11)
A36-8 (IGT4) - A36-4 (E01) W-L - B-L Ignition coil (ignition signal) Idling with warm engine Pulse generation
(See waveform 13)
A36-10 (IGT2) - A36-4 (E01) Y-R - B-L Ignition coil (ignition signal) Idling with warm engine Pulse generation
(See waveform 13)
A36-11 (PRG) - A36-4 (E01) R-G - B-L Purge valve One of the following conditions is met:
·

Ignition switch ON

·

Idling with warm engine, under purge control


Pulse generation
(See waveform 14)
A36-12 (#10) - A36-4 (E01) P - B-L Injector for port injection Idling with warm engine Pulse generation
(See waveform 15)
A36-13 (#40) - A36-4 (E01) P-G - B-L Injector for port injection Idling with warm engine Pulse generation
(See waveform 15)
A36-14 (#1) - A36-4 (E01) W - B-L Injector for direct injection Idling with warm engine Pulse generation
(See waveform 4)
A36-16 (OC2) - A36-4 (E01) GR - B-L Variable valve timing (VVT) sensor (Intake side (bank 2)) Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(See waveform 11)
A36-17 (OC1) - A36-4 (E01) G-W - B-L Variable valve timing (VVT) sensor (Intake side (bank 1)) Ignition switch ON 11 to 14 V
Idling with warm engine Pulse generation
(See waveform 11)
A36-18 (VTA1) - A36-29 (E1) LG - Y-B Throttle position sensor (for engine control) Ignition switch ON, Accelerator pedal fully released Approximately 0.6 V
Ignition switch ON, Accelerator pedal fully depressed Approximately 4.2 V
A36-19 (VC) - A36-29 (E1) R - Y-B Power source for sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
A36-20 (OT) - A36-29 (E1) BR - Y-B Oil temperature sensor Idling 0.5 to 1.4 V
A36-21 (IGT1) - A36-4 (E01) W-R - B-L Ignition coil (ignition signal) Idling with warm engine Pulse generation
(See waveform 13)
A36-22 (#20) - A36-4 (E01) P-L - B-L Injector for port injection Idling with warm engine Pulse generation
(See waveform 15)
A36-23 (#4) - A36-4 (E01) LG-R - B-L Injector for direct injection Idling with warm engine Pulse generation
(See waveform 4)
A36-24 (#3) - A36-4 (E01) LG-W - B-L Injector for direct injection Idling with warm engine Pulse generation
(See waveform 4)
A36-25 (#2) - A36-4 (E01) LG-B - B-L Injector for direct injection Idling with warm engine Pulse generation
(See waveform 4)
A36-28 (VTA2) - A36-29 (E1) R-Y - Y-B Throttle position sensor (for sensor malfunction detection) Ignition switch ON, Accelerator pedal fully released Approximately 1.5 V
Ignition switch ON, Accelerator pedal fully depressed Approximately 4.3 V
A36-30 (THW) - A36-29 (E1) BR-W - Y-B Engine coolant temperature sensor Idling, Engine coolant temperature 60 to 120°C (176 to 248°F) 0.8 to 1.8 V
A36-31 (IGT3) - A36-4 (E01) W-G - B-L Ignition coil (ignition signal) Idling with warm engine Pulse generation
(See waveform 13)
A36-32 (#30) - A36-4 (E01) P-B - B-L Injector for port injection Idling with warm engine Pulse generation
(See waveform 15)
A33-4 (EC) - Body ground B-L - Body ground Ground Always Below 1 Ω
A33-28 (SLE2) - Body ground - Shield Always Below 1 Ω
A34-1 (E03) - Body ground B-R - Body ground Ground Always Below 1 Ω
A34-2 (E04) - Body ground B-W - Body ground Ground Always Below 1 Ω
A34-3 (E05) - Body ground W - Body ground Ground Always Below 1 Ω
A34-29 (EKNK) - Body ground - Shield Always Below 1 Ω
A34-30 (SLE1) - Body ground GR - Body ground Shield Always Below 1 Ω
A34-35 (SLE3) - Body ground - Shield Always Below 1 Ω
A35-29 (EPA) - A36-4 (E01) L - B-L Ground Ignition switch ON 0 to 1 V
A35-30 (EPA2) - A36-4 (E01) Y-B - B-L Ground Ignition switch ON 0 to 1 V
A36-3 (E02) - Body ground B-Y - Body ground Ground Always Below 1 Ω
A36-4 (E01) - Body ground B-L - Body ground Ground Always Below 1 Ω
A36-29 (E1) - Body ground Y-B - Body ground Ground Ignition switch ON 0 to 1 V

*1: for Automatic Transmission

*2: for Manual Transmission

*3: w/ Entry and Start System

*4: w/o Entry and Start System

*5: w/ A/C

*6: w/o A/C

*7: w/ ID Code Box

*8: w/o ID Code Box

*9: w/ EVAP System

*10: except Automatic Air Conditioning System


WAVEFORM 1


A387798E02
2.771,0.271 3.354,0.479 0.583,0.208 10 false 1 V/DIV. 2.99,1.365 3.365,1.552 0.375,0.188 10 false GND 1.625,1.865 2.813,2.083 1.188,0.219 10 false 10 μsec./DIV.

CAN Communication Signal
ECM Terminal Name Between CANL and E01
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 2


A387797E03
2.74,0.333 3.427,0.563 0.688,0.229 10 false 1 V/DIV. 2.99,1.396 3.333,1.583 0.344,0.188 10 false GND 1.604,1.896 2.635,2.073 1.031,0.177 10 false 10 μsec./DIV.

CAN Communication Signal
ECM Terminal Name Between CANH and E01
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 3


A280139E03
2.917,1.031 3.271,1.271 0.354,0.24 10 false GND 1.292,1.917 2.052,2.167 0.76,0.25 10 false 50 ms./DIV. 2.76,0.375 3.313,0.604 0.552,0.229 10 false 5 V/DIV.

Air Fuel Ratio Sensor Heater
ECM Terminal Name Between HA1A and E01
Tester Range 5 V/DIV., 50 ms./DIV.
Condition Idling with cold engine


WAVEFORM 4


A280142E03
2.76,0.375 3.302,0.698 0.542,0.323 10 false 2 V/DIV. 2.906,1.042 3.26,1.313 0.354,0.271 10 false GND 2.906,1.594 3.26,1.865 0.354,0.271 10 false GND 1.229,1.927 1.969,2.146 0.74,0.219 10 false 40 μs./DIV. 0.198,1.042 0.51,1.302 0.313,0.26 10 false CH1 0.198,1.281 0.51,1.542 0.313,0.26 10 false CH2

Injector for Direct Injection No. 1 (to No. 4) Injection Signal
ECM Terminal Name CH1: Between #1 (to #4) and E01
CH2: Between IJF1or IJF2 and E01
Tester Range 2 V/DIV., 40 μs./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 5


A280144E03
2.896,1.021 3.25,1.26 0.354,0.24 10 false GND 2.75,0.385 3.292,0.625 0.542,0.24 10 false 2 V/DIV. 1.323,1.927 2.083,2.167 0.76,0.24 10 false 20 ms./DIV. 2.896,1.594 3.25,1.833 0.354,0.24 10 false GND 0.146,0.969 0.469,1.219 0.323,0.25 10 false CH1 0.156,1.271 0.479,1.521 0.323,0.25 10 false CH2

Fuel Pump for High Pressure (Spill Valve)
ECM Terminal Name CH1: Between FPD and E01
CH2: Between FPF and E01
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


WAVEFORM 6


A280152E03
2.896,0.646 3.25,0.885 0.354,0.24 10 false GND 2.896,1.219 3.25,1.448 0.354,0.229 10 false GND 2.896,1.604 3.25,1.854 0.354,0.25 10 false GND 2.75,0.354 3.302,0.594 0.552,0.24 10 false 5 V/DIV. 1.313,1.927 2.073,2.135 0.76,0.208 10 false 10 ms./DIV. 0.115,1.594 0.438,1.781 0.323,0.188 10 false CH3 0.115,1.219 0.438,1.406 0.323,0.188 10 false CH2 0.115,0.625 0.438,0.813 0.323,0.188 10 false CH1

Crankshaft Position Sensor and VVT Sensor for Exhaust Camshaft
ECM Terminal Name CH1: Between NE+ and NE-
CH2: Between EV1+ and E01
CH3: Between EV2+ and E01
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 7


A280151E03
2.885,0.656 3.24,0.896 0.354,0.24 10 false GND 2.885,1.229 3.24,1.469 0.354,0.24 10 false GND 2.885,1.604 3.24,1.844 0.354,0.24 10 false GND 2.75,0.354 3.313,0.583 0.563,0.229 10 false 5 V/DIV. 1.344,1.927 2.135,2.156 0.792,0.229 10 false 10 ms./DIV. 0.135,0.667 0.448,0.906 0.313,0.24 10 false CH1 0.135,1.135 0.448,1.375 0.313,0.24 10 false CH2 0.135,1.542 0.448,1.781 0.313,0.24 10 false CH3

Crankshaft Position Sensor and VVT Sensor for Intake Camshaft
ECM Terminal Name CH1: Between NE+ and NE-
CH2: Between VV1+ and E01
CH3: Between VV2+ and E01
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 8


A280149E03
2.896,1.042 3.26,1.281 0.365,0.24 10 false GND 2.75,0.365 3.292,0.635 0.542,0.271 10 false 5 V/DIV. 1.323,1.906 2.115,2.156 0.792,0.25 10 false 10 ms./DIV.

Engine Speed Signal
ECM Terminal Name Between TACH and E01
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Engine speed maintained at 1500 rpm

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 9


A280143E04
2.906,1.021 3.26,1.24 0.354,0.219 10 false GND 2.75,0.385 3.323,0.604 0.573,0.219 10 false 5 V/DIV. 1.354,1.906 2.24,2.125 0.885,0.219 10 false 5 ms./DIV.

Fuel Pump Control
ECM Terminal Name Between FPC and E01
Tester Range 5 V/DIV., 5 ms./DIV.
Condition Ignition switch ON


WAVEFORM 10


A280150E03
2.885,1.073 3.229,1.313 0.344,0.24 10 false GND 2.885,1.438 3.229,1.677 0.344,0.24 10 false GND 0.51,0.094 1.552,0.333 1.042,0.24 10 false 5 V/DIV. (CH1) 1.917,0.094 3.146,0.333 1.229,0.24 10 false 200 mV/DIV. (CH2) 1.25,2 2.104,2.156 0.854,0.156 10 false 500 μs./DIV. 0.188,0.875 0.5,1.146 0.313,0.271 10 false CH1 0.188,1.333 0.5,1.604 0.313,0.271 10 false CH2

Throttle Actuator
ECM Terminal Name CH1: Between M+ and E01
CH1: Between M- and E01
Tester Range CH1: 5 V/DIV., 500 μs./DIV.
CH2: 200 mV/DIV., 500 μs./DIV.
Condition Idling with warm engine


WAVEFORM 11


A280148E04
2.906,1.042 3.271,1.313 0.365,0.271 10 false GND 1.229,1.906 1.927,2.135 0.698,0.229 10 false 1 ms./DIV. 2.76,0.365 3.302,0.594 0.542,0.229 10 false 5 V/DIV.

Camshaft Timing Oil Control Valve (OCV)
ECM Terminal Name Between OC1, OC2, OE1 or OE2 and E01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine


WAVEFORM 12


A280147E04
2.906,1.229 3.271,1.458 0.365,0.229 10 false GND 2.74,0.375 3.292,0.604 0.552,0.229 10 false 5 V/DIV. 1.333,1.917 2.198,2.146 0.865,0.229 10 false 50 ms./DIV.

Heated Oxygen Sensor
ECM Terminal Name Between HT1B and E01
Tester Range 5 V/DIV., 50 ms./DIV.
Condition Idling with cold engine


WAVEFORM 13


A280145E04
2.885,1.042 3.24,1.333 0.354,0.292 10 false GND 2.75,0.354 3.323,0.646 0.573,0.292 10 false 2 V/DIV. 1.323,1.896 2.094,2.125 0.771,0.229 10 false 20 ms./DIV.

Ignition Coil (Ignition Signal)
ECM Terminal Name Between IGT (1 to 4) and E01
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


WAVEFORM 14


A280141E03
2.896,1.042 3.25,1.292 0.354,0.25 10 false GND 2.656,0.188 3.302,0.438 0.646,0.25 10 false 10 V/DIV. 1.333,1.906 1.938,2.156 0.604,0.25 10 false 2 s./DIV.

Purge Valve
ECM Terminal Name Between PRG and E01
Tester Range 10 V/DIV., 2 s./DIV.
Condition One of the following conditions is met:
·

Ignition switch ON

·

Idling with warm engine, under purge control




WAVEFORM 15


A280146E03
2.885,1.021 3.229,1.271 0.344,0.25 10 false GND 2.656,0.177 3.292,0.354 0.635,0.177 10 false 20 V/DIV. 1.26,1.906 2.052,2.083 0.792,0.177 10 false 20 ms./DIV.

Injector for Port Injection No. 1 (to No. 4) Injection Signal
ECM Terminal Name Between # (10 to 40) and E01
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.