Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM D

FA20 ENGINE CONTROL  SFI SYSTEM  DTC CHECK / CLEAR  


NOTICE:

When the diagnosis system is changed from normal mode to check mode or vice versa, all DTCs and freeze frame data recorded in normal mode are cleared. Before changing modes, always check and make a note of DTCs and freeze frame data.


HINT:
·

DTCs which are stored in the ECM can be displayed on the GTS. The GTS can display the current, pending and permanent DTCs.

·

If a malfunction is detected during the current driving cycle, current and permanent DTCs are stored.

·

Some DTCs are not stored if the ECM does not detect the same malfunction again during a second consecutive driving cycle. However, such malfunctions, detected on only one occasion, are stored as pending DTCs.

·

Current and pending DTCs can be cleared by using the GTS or by disconnecting the cable from the negative (-) battery terminal. However, permanent DTCs cannot be cleared using either of these two methods.

·

After clearing current DTCs using the GTS (or by disconnecting the cable from the negative battery terminal), permanent DTCs can be cleared when the system is determined to be normal for the relevant DTCs and then the universal trip is performed. The driving pattern to obtain a normal judgment is described under the "Confirmation Driving Pattern" for the respective DTC.


2 Trip Detection Examples
Pending DTC Store condition Malfunction detected
Clear condition System determined to be normal
or
DTCs cleared using GTS
or
Cable disconnected from negative (-) battery terminal
Current DTC Store condition Malfunction detected (2nd trip)
Clear condition No malfunctions in 40 driving cycles
or
DTCs cleared using GTS
or
Cable disconnected from negative (-) battery terminal
Permanent DTC Store condition Malfunction detected
Clear condition Ignition switch turned to ON after normal judgment obtained in 3 consecutive driving cycles
or
After DTCs cleared using GTS or cable disconnected from negative (-) battery terminal, normal judgment obtained and universal trip performed (not for misfire and fuel system DTCs)
or
After DTCs cleared using GTS or cable disconnected from negative (-) battery terminal, malfunction not detected when universal trip driving performed (misfire and fuel system DTCs)
MIL ON Malfunction detected
OFF Ignition switch turned to ON after normal judgment obtained in 3 consecutive driving cycles
or
DTCs cleared using GTS
or
Cable disconnected from negative (-) battery terminal


A198847E61
0.094,0.104 1.854,0.281 1.76,0.177 10 false 2 Trip Detection Examples 0.083,1.094 0.365,1.292 0.281,0.198 10 false Trip 0.083,1.698 1.406,1.844 1.323,0.146 10 false Pending DTC Status 0.094,2.313 1.375,2.479 1.281,0.167 10 false Current DTC Status 0.083,3.021 0.823,3.188 0.74,0.167 10 false MIL Status 0.083,3.667 1.573,3.833 1.49,0.167 10 false Permanent DTC Status 1.531,0.396 1.917,0.583 0.385,0.188 10 false 1 Trip 2.365,0.396 2.75,0.583 0.385,0.188 10 false 2 Trip 3.208,0.396 3.594,0.583 0.385,0.188 10 false 3 Trip 4.052,0.385 4.438,0.573 0.385,0.188 10 false 4 Trip 4.896,0.396 5.281,0.583 0.385,0.188 10 false 5 Trip 5.729,0.396 6.115,0.583 0.385,0.188 10 false 6 Trip 6.542,0.406 7,0.594 0.458,0.188 10 false 43 Trip 0.708,0.969 1.156,1.146 0.448,0.177 10 false Driving 0.708,1.302 1.135,1.469 0.427,0.167 10 false IG off 0.354,4.094 1.823,4.281 1.469,0.188 10 false : Malfunction detected 0.354,4.427 1.542,4.615 1.188,0.188 10 false : Normal judgment 1.729,1.75 2,1.906 0.271,0.156 10 false ON 1.375,2.104 1.688,2.281 0.313,0.177 10 false OFF 2.573,2.406 2.844,2.563 0.271,0.156 10 false ON 2.219,2.74 2.531,2.917 0.313,0.177 10 false OFF 2.573,3.052 2.844,3.208 0.271,0.156 10 false ON 2.219,3.396 2.531,3.573 0.313,0.177 10 false OFF 2.573,3.729 2.844,3.885 0.271,0.156 10 false ON 2.219,4.073 2.531,4.25 0.313,0.177 10 false OFF

A198848E72
0.115,0.073 6.281,0.406 6.167,0.333 10 false 2 Trip Detection Examples (Instance when DTCs were cleared midway through by using the GTS or by disconnecting the cable from the negative battery terminal) 0.083,1.302 0.365,1.5 0.281,0.198 10 false Trip 0.083,1.969 1.396,2.135 1.313,0.167 10 false Pending DTC Status 0.083,2.594 1.354,2.76 1.271,0.167 10 false Current DTC Status 0.083,3.26 0.802,3.427 0.719,0.167 10 false MIL Status 0.083,3.906 1.573,4.073 1.49,0.167 10 false Permanent DTC Status 2.042,0.771 2.427,0.948 0.385,0.177 10 false 1 Trip 3,0.771 3.385,0.948 0.385,0.177 10 false 2 Trip 3.969,0.771 4.354,0.948 0.385,0.177 10 false 3 Trip 4.948,0.771 5.354,0.958 0.406,0.188 10 false 4 Trip 1.115,1.292 1.573,1.469 0.458,0.177 10 false Driving 1.115,1.635 1.573,1.813 0.458,0.177 10 false IG off 0.354,5.417 1.948,5.583 1.594,0.167 10 false : Universal trip performed 5.396,0.615 7.083,0.844 1.688,0.229 10 false Universal trip driving pattern 2.229,2.063 2.5,2.219 0.271,0.156 10 false ON 1.896,2.427 2.208,2.583 0.313,0.156 10 false OFF 3.198,2.688 3.469,2.844 0.271,0.156 10 false ON 2.865,3.042 3.177,3.198 0.313,0.156 10 false OFF 3.198,3.344 3.469,3.5 0.271,0.156 10 false ON 2.865,3.708 3.177,3.865 0.313,0.156 10 false OFF 3.198,4.01 3.469,4.167 0.271,0.156 10 false ON 2.865,4.365 3.24,4.521 0.375,0.156 10 false OFF 0.354,4.406 1.771,4.583 1.417,0.177 10 false : Malfunction detected 0.365,4.729 4.896,4.896 4.531,0.167 10 false : After problem areas repaired and DTCs cleared, DTC check performed 0.354,5.083 1.521,5.25 1.167,0.167 10 false : Normal judgment

HINT:
·

Obtaining a normal judgment and performing a universal trip driving pattern can be done in the same driving cycle or in different driving cycles.

·

It is unnecessary to obtain a normal judgment if the DTCs are misfire or fuel system DTCs.



CHECK DTC


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Check DTCs and freeze frame data, and then write them down.




CLEAR DTC (Pending and Current DTC)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Clear DTCs.



CLEAR DTC (Pending and Current DTC without using GTS)


a.

Perform either of the following operations:

NOTICE:

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


i.

Disconnect the cable from the negative (-) battery terminal for more than 1 minute.


ii.

Remove the EFI (+B) fuse from the engine room relay block assembly located inside the engine compartment for more than 1 minute.




CLEAR PERMANENT DTC


HINT:

Even if the following procedure is not performed, permanent DTCs are cleared by obtaining a normal judgment during 3 consecutive driving cycles.


A198849E99
0.125,0.083 2.042,0.281 1.917,0.198 10 false Universal Trip Driving Pattern 0.521,1.135 1.688,1.292 1.167,0.156 10 false 40 km/h (25 mph) 1.24,2.333 1.635,2.521 0.396,0.188 10 false Idling 0.281,2.635 1.708,2.813 1.427,0.177 10 false Ignition Switch to ON 0.438,2.938 1.615,3.115 1.177,0.177 10 false Ignition Switch off 3.292,0.458 4.948,0.625 1.656,0.167 10 false Total of 5 minutes or more 2.115,2.688 3.406,2.854 1.292,0.167 10 false 30 seconds or more 3.146,3.188 4.385,3.354 1.24,0.167 10 false 10 minutes or more 4.969,3.396 6.396,3.563 1.427,0.167 10 false Permanent DTC Clear

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Check if permanent DTCs are stored.

HINT:

If permanent DTCs are not output, it is not necessary to continue this procedure.



f.

Clear DTCs.


g.

Perform the respective confirmation driving patterns in order to obtain a normal judgment for the output DTCs.

HINT:
·

Confirmation driving patterns do not need to be performed for misfire and fuel system DTCs.

·

For the confirmation driving pattern, refer to the procedures for the relevant DTC (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).




h.

Perform the universal trip.

HINT:

The driving pattern to obtain a normal judgment and the universal trip driving can be performed consecutively in the same driving cycle.


1.

Idle the engine for 30 seconds or more.

2.

Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

It is possible to complete the drive pattern even if the vehicle decelerates to less than 40 km/h (25 mph) during the driving cycle provided that the vehicle is driven at 40 km/h (25 mph) or more for a total of 5 minutes.


3.

Allow 10 minutes or more to elapse from the time the engine is started.



i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Check that the permanent DTCs have been cleared.

HINT:

The permanent DTCs are cleared when the universal trip is completed.