If any of the following DTCs are stored, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily or stops fuel injection.
| DTC Code | Fail-Safe Operation | Fail-Safe Deactivation Condition |
|---|---|---|
| P000A
P000C P0010 P0011 P0016 P0018 P0020 P0021 P0341 P0345 P0346 |
Fix intake VVT control at intermediate position | After recovery in normal status, turn the ignition switch to ON again |
| P000B
P000D P0013 P0014 P0017 P0019 P0023 P0024 P0365 P0366 P0390 P0391 |
Fix exhaust VVT control at maximum advanced angle | After recovery in normal status, turn the ignition switch to ON again |
| P0031
P0032 P0131 P0132 P0134 |
Stop air fuel ratio feedback control | After recovery in normal status, turn the ignition switch to ON again |
| P0037
P0137 P0138 P013A P013B P013E P013F P0141 P2270 P2271 |
Stop air fuel ratio secondary feedback control | Return to normal status |
| P0087
P0088 P0191 P0192 P0193 P1235 |
·
Stop fuel pump assembly drive (high pressure side) ·
Fix fuel pressure at 0.4 MPa (4.07 kgf/cm2, 57.9 psi). ·
Cut fuel at 1500 rpm or more |
After recovery in normal status, turn the ignition switch to ON again |
| P0101
P0102 P0103 |
Make the engine load the manifold absolute pressure converted estimated value | Return to normal status |
| P0068
P0107 P0108 |
Make the manifold absolute pressure value the mass air flow meter converted estimated value | Return to normal status |
| P0111
P0112 P0113 |
Fix inlet air temperature at 20°C (68°F) | Return to normal status |
| P0116
P0117 P0118 P0125 |
·
Fix coolant temperature at 70°C ( 158°F) ·
Stop intake and exhaust VVT |
Return to normal status |
| P0172 | Stop purge control | Return to normal status |
| P0196
P0197 P0198 |
Fix engine oil temperature at 70°C (158°F) | Return to normal status |
| P0201
P0202 P0203 P0204 P062D P1261 P1262 P1263 P1264 |
·
Cut fuel at 1500 rpm or more ·
Cut fuel to abnormal cylinders |
After recovery in normal status, turn the ignition switch to ON again |
| P062F
P0122 P0123 P0222 P0223 P0604 P0605 P0606 P060A P060B P1160 P2101 P2102 P2109 P2119 P2135 |
Stop electronic throttle control, and fix the throttle valve opening angle (7 degrees) | After recovery in normal status, turn the ignition switch to ON again |
| P0327
P0328 P0332 P0333 |
Maximum retard angle | Return to normal status |
| P0451 | Stop leak detection pump control | Return to normal status |
| P0500
P2158 |
Fix ECU recognized vehicle speed at 10 km/h (6.2 mph) | Return to normal status |
| P0851
P0852 |
Turn off the gear position display within the combination meter (for Manual Transmission) | Return to normal status |
| P1451
P2404 |
Fix atmospheric pressure at 101.3 kPa (760 mmHg) | Return to normal status |
| P2122
P2123 P2127 P2128 |
Accelerator pedal sensor assembly has 2 sensor circuits: Main and Sub If either circuit malfunctions, substitute the normal accelerator position sensor until the prescribed angle.
If both circuits malfunction, fix accelerator position at prescribed angle (15%). |
After recovery in normal status, turn the ignition switch to ON again |
| P2138 | ·
Fix accelerator pedal angle ·
Stop electronic throttle control, and fix the throttle valve opening angle |
After recovery in normal status, turn the ignition switch to ON again |