Home › Engine / Hybrid System › FA20 (ENGINE MECHANICAL) › ENGINE UNIT › from 2016.06
RM2090E _51 Engine / Hybrid System _060666 FA20 ENGINE MECHANICAL _0297496 ENGINE UNIT G

FA20 ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13801 1.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A125485

Check that the roller moves smoothly by rotating it by hand.

Replace the No. 1 valve rocker arm sub-assembly if the roller does not rotate smoothly.


Hide 13506 2.INSPECT CHAIN SUB-ASSEMBLY

a.

Check the chain sub-assembly for deformation, cracks or other damages.

If the chain sub-assembly has any defects, replace it.


Hide 3.INSPECT CAMSHAFT TIMING GEAR

a.

Check the camshaft timing gear teeth for abnormal wear and scratches.

If the camshaft timing gear has any defects, replace it.


Hide 13521 4.INSPECT CRANKSHAFT TIMING GEAR OR SPROCKET

a.

Check the crankshaft timing gear or sprocket teeth for abnormal wear and scratches.

If necessary, replace it.


b.

Check that there is no play between the crankshaft timing gear or sprocket and the key.

If necessary, replace the crankshaft timing gear or sprocket or the key.


Hide 13559 5.INSPECT CHAIN TENSIONER SLIPPER

a.

Check the chain tensioner slipper for deformation, cracks or other damages.


Hide 13561 6.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.

Check the No. 1 chain vibration damper for deformation, cracks or other damages.


Hide 13540 7.INSPECT CHAIN TENSIONER ASSEMBLY

a.

Check the chain tensioner assembly for deformation, cracks or other damages.


b.
A279536

Check that the plunger moves smoothly when it is unlocked.

If the plunger does not move smoothly, replace the chain tensioner assembly.


c.

Check that the plunger does not move when it is locked.


Hide 11103C 8.INSPECT CAMSHAFT HOUSING SUB-ASSEMBLY

a.

Visually check the oil control valve filters, and if clogging is found, replace them with new ones.


b.

Check the camshaft housing sub-assembly journals for damage and wear. Replace the camshaft housing sub-assembly if necessary.


Hide 9.INSPECT CAMSHAFT

a.

Check the camshaft journals for damage and wear.

Replace the camshaft if necessary.


b.

Check the cam face condition.

Replace the camshaft if uneven wear is found.

HINT:

Remove the minor faults by smoothing the surface with 400-grit sandpaper.



c.

Inspect for runout.

i.

Place the camshaft on V-blocks.


ii.
A278753

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.020 mm (0.00079 in.)


If the circle runout is more than the maximum, replace the camshaft.

HINT:

Measurement should be performed at a temperature of 20°C (68°F).




d.
A283338E01
1.811,2.344 1.944,2.511 0.133,0.167 10 C 1.004,3.135 1.137,3.301 0.133,0.167 10 B 0.282,2.344 0.415,2.511 0.133,0.167 10 A 2.509,1.707 2.698,1.879 0.188,0.172 10 *b 0.997,1.707 1.185,1.879 0.188,0.172 10 *a

Inspect for cam height.

i.

Using a micrometer, measure the cam lobe height.

Standard height (Intake):
Position Standard
A 40.39 to 40.49 mm (1.5902 to 1.5941 in.)
B 34.0 mm (1.3386 in.)


Standard height (Exhaust):
Position Standard
A 40.19 to 40.29 mm (1.5823 to 1.5862 in.)
B 34.0 mm (1.3386 in.)


Standard height (For fuel pump):
Position Standard
C 38.95 to 39.05mm {1.5335 to 1.5374in}


Text in Illustration
*a For Valve
*b For Fuel Pump

If the result is not as specified, replace the camshaft.

HINT:

Measurement should be performed at a temperature of 20°C (68°F).




e.
A278755

Inspect for camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard journal diameter:

25.946 to 25.963 mm (1.02149 to 1.02216 in.)


If the result is not as specified, check the oil clearance.

HINT:

Measurement should be performed at a temperature of 20°C (68°F).




Hide 10.INSPECT CAMSHAFT OIL CLEARANCE

a.
A278760

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.0068 to 0.1160 mm (0.00027 to 0.00457 in.)


If the clearance is not as specified or if uneven wear is found, replace each camshaft cap and camshaft housing as a set. If necessary replace the camshaft.

HINT:
·

Measurement should be performed at a temperature of 20°C (68°F).

·

Set the dial indicator at the end surface of the camshaft.




Hide 11.INSPECT CAMSHAFT OIL CLEARANCE

HINT:

Measurement should be performed at a temperature of 20°C (68°F).


a.

Remove the seal packing from camshaft housing and front camshaft cap, intake rear camshaft cap and exhaust rear camshaft cap.


b.

Clean each camshaft cap and camshaft housing journal.


c.

Set the camshafts on the camshaft housing.


d.

Place a plastigauge across the camshaft journals and set the camshaft caps.


e.

Tighten the bolts in the order shown in the illustration to install the front camshaft cap, intake center camshaft cap, intake rear camshaft cap, exhaust center camshaft cap and exhaust rear camshaft cap.

U146840E01
0.682,1.319 0.858,1.486 0.176,0.167 10 9 3.783,0.255 3.989,0.443 0.206,0.188 10 *b 0.281,0.255 0.486,0.443 0.206,0.188 10 *a 6.417,1.585 6.593,1.752 0.176,0.167 10 12 6.011,0.551 6.187,0.718 0.176,0.167 10 11 6.417,1.269 6.593,1.436 0.176,0.167 10 10 2.434,2.312 2.610,2.479 0.176,0.167 10 8 2.434,0.597 2.610,0.764 0.176,0.167 10 7 2.816,1.588 2.992,1.755 0.176,0.167 10 6 2.816,1.321 2.992,1.488 0.176,0.167 10 5 1.714,2.266 1.891,2.433 0.176,0.167 10 4 2.114,1.626 2.291,1.793 0.176,0.167 10 3 1.71,0.647 1.886,0.814 0.176,0.167 10 2 2.114,1.301 2.291,1.468 0.176,0.167 10 1 6.015,2.315 6.192,2.482 0.176,0.167 10 13 1.023,2.307 1.199,2.474 0.176,0.167 10 12 0.638,1.612 0.814,1.779 0.176,0.167 10 11 1.026,0.633 1.202,0.800 0.176,0.167 10 10 5.003,0.589 5.179,0.756 0.176,0.167 10 9 4.471,2.332 4.647,2.499 0.176,0.167 10 8 4.499,0.526 4.675,0.693 0.176,0.167 10 7 4.115,1.559 4.291,1.726 0.176,0.167 10 6 4.114,1.28 4.290,1.447 0.176,0.167 10 5 5.339,2.289 5.515,2.456 0.176,0.167 10 4 5.341,0.588 5.517,0.755 0.176,0.167 10 2 5.731,1.238 5.907,1.405 0.176,0.167 10 1 5.736,1.605 5.912,1.772 0.176,0.167 10 3

Text in Illustration
*a for Bank 1 *b for Bank 2

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


f.

Using several steps, uniformly loosen the bolts in the order shown in the illustration, and remove the front camshaft cap, intake center camshaft cap, intake rear camshaft cap, exhaust center camshaft cap and exhaust rear camshaft cap.

U146841E01
1.708,2.262 1.884,2.429 0.176,0.167 10 9 3.883,0.256 4.089,0.444 0.206,0.188 10 *b 0.381,0.256 0.586,0.444 0.206,0.188 10 *a 5.295,0.579 5.471,0.746 0.176,0.167 10 12 5.289,2.302 5.466,2.469 0.176,0.167 10 10 2.81,1.312 2.986,1.479 0.176,0.167 10 8 2.815,1.579 2.991,1.746 0.176,0.167 10 7 2.425,0.608 2.602,0.775 0.176,0.167 10 6 2.435,2.315 2.611,2.482 0.176,0.167 10 5 0.684,1.316 0.861,1.483 0.176,0.167 10 4 1.077,0.639 1.253,0.806 0.176,0.167 10 3 0.681,1.599 0.857,1.766 0.176,0.167 10 2 1.058,2.301 1.234,2.468 0.176,0.167 10 1 5.706,1.247 5.883,1.414 0.176,0.167 10 13 2.066,1.304 2.242,1.471 0.176,0.167 10 12 1.669,0.653 1.846,0.820 0.176,0.167 10 11 2.07,1.615 2.246,1.782 0.176,0.167 10 10 4.1,1.284 4.276,1.451 0.176,0.167 10 9 4.1,1.548 4.276,1.715 0.176,0.167 10 8 4.493,0.519 4.669,0.686 0.176,0.167 10 7 4.473,2.325 4.649,2.492 0.176,0.167 10 6 5.007,0.579 5.183,0.746 0.176,0.167 10 5 6.425,1.269 6.601,1.436 0.176,0.167 10 4 6.039,0.551 6.216,0.718 0.176,0.167 10 3 6.425,1.568 6.601,1.735 0.176,0.167 10 2 6.063,2.325 6.240,2.492 0.176,0.167 10 1 5.713,1.612 5.889,1.779 0.176,0.167 10 11

Text in Illustration
*a for Bank 1 *b for Bank 2


g.
A278791

Measure the widest point of the plastigauge on each journal.

Standard oil clearance:

0.037 to 0.072 mm (0.00146 to 0.00283 in.)


If the clearance is not as specified, replace each camshaft cap and camshaft housing as a set. If necessary, replace the camshaft.


h.

Completely remove the plastigauge.