Home › Engine / Hybrid System › FA20 (ENGINE MECHANICAL) › CYLINDER HEAD › from 2016.06
RM2090E _51 Engine / Hybrid System _060666 FA20 ENGINE MECHANICAL _0297497 CYLINDER HEAD A

FA20 ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122B 1.REPLACE NO. 2 INTAKE VALVE GUIDE BUSH

a.

Place the cylinder block on wooden blocks with the combustion chamber side facing upward.


b.
A278775E01
2.313,2.29 2.623,2.456 0.310,0.166 10 SST 1.577,1.262 2.269,2.292 2.269,2.292 1.657,1.058 false

Using SST and a hammer, tap out the No. 2 intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

NOTICE:
·

Place wooden blocks wrapped in a cloth under the cylinder head and stabilize the cylinder head during servicing.

·

Use special care not to damage the cylinder head.




c.

Before installing the No. 2 intake valve guide bush, make sure that neither scratches nor damages exist on the inner surface of cylinder head valve guide bush holes.


d.
A281653E03
1.49,0.479 1.115,0.885 false 2.156,0.24 2.875,0.583 0.719,0.344 10 false 7.6 mm 1.01,0.885 1.24,1.135 0.229,0.25 10 false *a

Draw a reference line 7.6 mm (0.299 in.) below from the top face on a new No. 2 intake valve guide bush using a marker.

Text in Illustration
*a Reference line

HINT:

Reference line is used as a guide when tapping-in the No. 2 intake valve guide bush.



e.

Place the cylinder block on wooden blocks with the combustion chamber side facing downward.


f.

Apply enough engine oil to the No. 2 intake valve guide bush, and set it on the cylinder head.


g.
A278777E01
2.369,1.888 2.699,2.051 0.329,0.163 10 SST 1.547,1.185 2.347,1.879 2.347,1.879 1.617,0.98 false

Using SST and a hammer, tap in the No. 2 intake valve guide bush to the reference line.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

NOTICE:
·

Place wooden blocks wrapped in a cloth under the cylinder head and stabilize the cylinder head during servicing.

·

Use special care not to damage the cylinder head.




h.
A278778E03
0.146,2.271 0.323,2.438 0.177,0.167 10 false *a

While measuring the No. 2 intake valve guide bush protrusion amount using a vernier caliper, tap in the No. 2 intake valve guide bush so that its height is within the standard.

Standard protrusion height:

11.4 to 11.8 mm (0.449 to 0.466 in.)


NOTICE:
·

Place wooden blocks wrapped in a cloth under the cylinder head and stabilize the cylinder head during servicing.

·

Use special care not to damage the cylinder head.



HINT:

Use multiple small repetitions of tap-in and measurement in order not to excessively tap in the No. 2 intake valve guide bush.


Text in Illustration
*a Protrusion height


i.

Place the cylinder block on wooden blocks with the combustion chamber side facing upward.

NOTICE:
·

Place wooden blocks wrapped in a cloth under the cylinder head and stabilize the cylinder head during servicing.

·

Use special care not to damage the cylinder head.




j.
A281465

Using a reamer, ream the No. 2 intake valve guide bush to obtain the standard clearance between the No. 2 intake valve guide bush and valve stem.

Standard inside diameter:

5.500 to 5.512 mm (0.21654 to 0.21701 in.) at 20°C (68°F)


NOTICE:

While gradually widening the reamer diameter, ream the No. 2 intake valve guide bush uniformly so that the oil clearance is within the standard.


HINT:
·

Apply engine oil to the reamer when reaming.

·

If the inner surface of No. 2 intake valve guide bush is damaged, slightly grind the edge of the reamer with 400-grit sandpaper.

·

If the inner surface of No. 2 intake valve guide bush becomes lustrous and the reamer does not chip, use a new reamer or correct the reamer.




k.

After reaming, remove chips and clean the No. 2 intake valve guide bush.


l.

Measure the inside diameter of the No. 2 intake valve guide bush and confirm the oil clearance.


m.

Check the contact condition between the valve and valve seat.


Hide 11126B 2.REPLACE NO. 2 EXHAUST VALVE GUIDE BUSH

a.

Place the cylinder block on wooden blocks with the combustion chamber side facing upward.


b.
A279602E01
2.768,0.413 3.086,0.578 0.318,0.165 10 SST 2.259,0.594 2.727,0.522 2.727,0.522 2.237,1.175 false

Using SST and a hammer, tap out the No. 2 exhaust valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

NOTICE:
·

Place wooden blocks wrapped in a cloth under the cylinder head and stabilize the cylinder head during servicing.

·

Use special care not to damage the cylinder head.




c.

Before installing the No. 2 exhaust valve guide bush, make sure that neither scratches nor damages exist on the inner surface of cylinder head valve guide bush holes.


d.
A278776E06
1.458,0.479 1.104,0.854 false 2.156,0.24 2.677,0.406 0.521,0.167 10 false 7.0 mm 0.948,0.802 1.177,0.969 0.229,0.167 10 false *a

Draw a reference line 7.0 mm (0.276 in.) below from the top face on a new No. 2 exhaust valve guide bush using a marker.

Text in Illustration
*a Reference line

HINT:

Reference line is used as a guide when tapping-in the No. 2 exhaust valve guide bush.



e.

Place the cylinder block on wooden blocks with the combustion chamber side facing downward.


f.

Apply enough engine oil to the No. 2 exhaust valve guide bush, and set it on the cylinder head.


g.
A278777E01
2.369,1.888 2.699,2.051 0.329,0.163 10 SST 1.547,1.185 2.347,1.879 2.347,1.879 1.617,0.98 false

Using SST and a hammer, tap in the No. 2 exhaust valve guide bush to the reference line.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

NOTICE:
·

Place wooden blocks wrapped in a cloth under the cylinder head and stabilize the cylinder head during servicing.

·

Use special care not to damage the cylinder head.




h.
A278778E03
0.146,2.271 0.323,2.438 0.177,0.167 10 false *a

While measuring the No. 2 exhaust valve guide bush protrusion amount using a vernier caliper, tap in the No. 2 exhaust valve guide bush so that its height is within the standard.

Standard protrusion height:

11.4 to 11.8 mm (0.449 to 0.466 in.)


NOTICE:
·

Place wooden blocks wrapped in a cloth under the cylinder head and stabilize the cylinder head during servicing.

·

Use special care not to damage the cylinder head.



HINT:

Use multiple small repetitions of tap-in and measurement in order not to excessively tap in the No. 2 exhaust valve guide bush.


Text in Illustration
*a Protrusion height


i.

Place the cylinder block on wooden blocks with the combustion chamber side facing upward.

NOTICE:
·

Place wooden blocks wrapped in a cloth under the cylinder head and stabilize the cylinder head during servicing.

·

Use special care not to damage the cylinder head.




j.
A281465

Using a reamer, ream the No. 2 exhaust valve guide bush to obtain the standard clearance between the No. 2 exhaust valve guide bush and valve stem.

Standard inside diameter:

5.500 to 5.512 mm (0.21654 to 0.21701 in.) at 20°C (68°F)


NOTICE:

While gradually widening the reamer diameter, ream the No. 2 exhaust valve guide bush uniformly so that the oil clearance is within the standard.


HINT:
·

Apply engine oil to the reamer when reaming.

·

If the inner surface of No. 2 exhaust valve guide bush is damaged, slightly grind the edge of the reamer with 400-grit sandpaper.

·

If the inner surface of No. 2 exhaust valve guide bush becomes lustrous and the reamer does not chip, use a new reamer or correct the reamer.




k.

After reaming, remove chips and clean the No. 2 exhaust valve guide bush.


l.

Measure the inside diameter of the No. 2 exhaust valve guide bush and confirm the oil clearance.


m.

Check the contact condition between the valve and valve seat.