Home › Engine / Hybrid System › FA20 (ENGINE MECHANICAL) › CYLINDER HEAD
RM2090E _51 Engine / Hybrid System _060666 FA20 ENGINE MECHANICAL _0297497 CYLINDER HEAD A

FA20 ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


PROCEDURE

Hide 13711E 1.INSTALL INTAKE VALVE STEM OIL SEAL

a.
A146313E12
0.096,0.196 0.331,0.366 0.235,0.170 10 *a 1.884,0.196 2.081,0.356 0.198,0.161 10 *b 2.861,0.658 3.053,0.832 0.193,0.174 10 *d 0.976,0.653 1.188,0.827 0.211,0.174 10 *c 0.957,0.734 0.837,0.734 0.837,0.734 0.712,0.995 false 2.842,0.746 2.721,0.746 2.721,0.746 2.597,1.007 false

Apply engine oil to new valve stem oil seals.

Text in Illustration
*a for Intake
*b for Exhaust
*c Gray
*d Light green

NOTICE:
·

Pay close attention to the colors when installing the oil seals.

·

Installing the intake oil seal into the exhaust side or installing the exhaust oil seal to the intake side may cause installation problems later.




b.
A281043E03
3.083,2.417 3.083,2.781 true 1.26,1.26 0.604,1.76 true 0.302,1.708 0.615,1.885 0.313,0.177 10 false SST 2.927,2.802 3.24,2.979 0.313,0.177 10 false SST 1.542,2.323 1.729,2.49 0.188,0.167 10 false *b 0.552,2.323 0.74,2.49 0.188,0.167 10 false *a

Using SST, push in the oil seals by hand.

SST
09201-41020  

Text in Illustration
*a Correct
*b Incorrect

NOTICE:
·

Place a cloth, etc. to avoid scratching the mating surface of the cylinder head during servicing.

·

Do not tap SST with a plastic hummer to install the oil seals as it may damage the oil seals. Push in the oil seals by hand with SST.

·

Do not install the oil seals at an angle.




Hide 13715A 2.INSTALL EXHAUST VALVE STEM OIL SEAL

a.

Using SST, push in the oil seals by hand.

SST
09201-41020  

HINT:

Use the same procedure as for the intake oil seals.



Hide 13711 3.INSTALL INTAKE VALVE

NOTICE:

Place a cloth to avoid scratching the mating surface of the cylinder head during servicing.


a.

Set the valve spring seat, valve spring and retainer onto the cylinder head.

HINT:

Install the valve spring to the cylinder head with the narrow pitch end facing the valve spring seat.



b.

Apply engine oil to the valve stem and insert the valve into the valve guide bush.

NOTICE:

When inserting the valve into the valve guide bush, use special care not to damage the oil seal lip.



c.

Apply engine oil to the valve spring retainer locks.


d.
A278769E01
0.163,0.559 0.500,0.728 0.336,0.170 10 SST 0.537,0.67 0.874,0.972 false

Using SST, compress the valve spring and install the valve spring retainer locks.

SST
09202-70020  (09202-00010, 09202-01010, 09202-01020)


e.
A279609

Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to tap the retainer.



Hide 13715 4.INSTALL EXHAUST VALVE

NOTICE:

Place a cloth to avoid scratching the mating surface of the cylinder head during servicing.


a.

Set the valve spring seat, valve spring and retainer onto the cylinder head.

HINT:

Install the valve spring to the cylinder head with the narrow pitch end facing the valve spring seat.



b.

Apply engine oil to the valve stem and insert the valve into the valve guide bush.

NOTICE:

When inserting the valve into the valve guide bush, use special care not to damage the oil seal lip.



c.

Apply engine oil to the valve spring retainer locks.


d.
A279601E01
1.478,0.216 1.801,0.393 0.323,0.177 10 SST 1.856,0.317 2.248,0.398 false

Using SST, compress the valve spring and install the valve spring retainer locks.

SST
09202-70020  (09202-00010, 09202-01010, 09202-01020)


e.
A279610

Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to tap the retainer.



Hide 5.INSTALL STUD BOLT

a.
A278768E01
0.173,2.26 0.358,2.445 0.185,0.185 10 *b 0.173,0.112 0.358,0.297 0.185,0.185 10 *a

Install the 6 stud bolts to the cylinder heads.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

Text in Illustration
*a for Bank 1
*b for Bank 2


Hide 6.INSTALL CHAIN COVER MOUNT BOLT

a.
A278767

Install the chain cover mount bolt to the cylinder head sub-assembly LH.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)