Home › Engine / Hybrid System › FA20 (ENGINE MECHANICAL) › CYLINDER HEAD
RM2090E _51 Engine / Hybrid System _060666 FA20 ENGINE MECHANICAL _0297497 CYLINDER HEAD A

FA20 ENGINE MECHANICAL  CYLINDER HEAD  REPAIR  


PROCEDURE

Hide 1.REPAIR INTAKE VALVE SEATS

NOTICE:
·

Repair the seat while checking the seating position.

·

Releasing the seat cutter pressure gradually helps to make the intake valve seat faces smoother.



a.
A278782E01
2.479,0.421 2.746,0.579 0.267,0.158 10 75° 2.772,0.591 3.039,0.749 0.267,0.158 10 45° 2.812,1.045 3.079,1.203 0.267,0.158 10 30°

Using a 45° cutter, resurface the valve seat so that the valve seat width is more than the specification.


b.

Hand-lap the valve and valve seat with an abrasive compound.


c.

Check the valve seating position.

HINT:

This procedure is necessary to select a cutter to be used in the following steps.



d.

Using 30° or 75° cutters, correct the valve seat so that the contact condition between the valve and valve seat is within the standard.

A279608E01
5.818,0.386 5.976,0.566 0.158,0.180 10 C 3.394,0.386 3.552,0.566 0.158,0.180 10 B 1.012,0.386 1.170,0.566 0.158,0.180 10 A 6.362,3.366 6.751,3.527 0.389,0.161 10 30° 6.578,3.163 6.967,3.325 0.389,0.161 10 45° 6.833,3.015 7.147,3.176 0.314,0.161 10 75° 3.84,3.366 4.229,3.527 0.389,0.161 10 30° 4.056,3.163 4.445,3.325 0.389,0.161 10 45° 4.342,3.015 4.731,3.176 0.389,0.161 10 75° 1.248,3.366 1.637,3.527 0.389,0.161 10 30° 1.464,3.163 1.853,3.325 0.389,0.161 10 45° 1.751,3.015 2.139,3.176 0.389,0.161 10 75°

NOTICE:
·

Repair the seat while checking the seating position.

·

Releasing the seat cutter pressure gradually helps to make the intake valve seat faces smoother.



HINT:

Select an appropriate cutter by referring to the following chart.


Contact position Cutter to be selected
A in the illustration If the valve face position is high, use a 30° valve seat cutter in order to grind the surface so that the contact surface between the valve and the valve seat is at a standard value.
B in the illustration If the valve face position is low, use a 75° valve seat cutter in order to grind the surface so that the contact surface between the valve and the valve seat is at a standard value.
C in the illustration If the valve face position is centered, use a 30°and 75° valve seat cutter in order to grind the surface so that the contact surface between the valve and the valve seat is at a standard value.


e.

Hand-lap the valve and valve seat with an abrasive compound.


Hide 2.REPAIR EXHAUST VALVE SEATS

NOTICE:
·

Repair the seat while checking the seating position.

·

Releasing the seat cutter pressure gradually helps to make the intake valve seat faces smoother.



a.
A279605E01
0.39,0.645 0.657,0.803 0.267,0.158 10 45° 0.694,0.534 0.961,0.692 0.267,0.158 10 60° 0.35,1.151 0.617,1.309 0.267,0.158 10 30°

Using a 45° cutter, resurface the valve seat so that the valve seat width is more than the specification.


b.

Hand-lap the valve and valve seat with an abrasive compound.


c.

Check the valve seating position.

HINT:

This procedure is necessary to select a cutter to be used in the following steps.



d.

Using 30° or 60° cutters, correct the valve seat so that the contact condition between the valve and valve seat is within the standard.

A279608E02
5.818,0.386 5.976,0.566 0.158,0.180 10 C 3.394,0.386 3.552,0.566 0.158,0.180 10 B 1.012,0.386 1.170,0.566 0.158,0.180 10 A 6.362,3.365 6.751,3.527 0.389,0.161 10 30° 6.578,3.163 6.967,3.325 0.389,0.161 10 45° 6.833,3.015 7.147,3.176 0.314,0.161 10 60° 3.84,3.365 4.229,3.527 0.389,0.161 10 30° 4.056,3.163 4.445,3.325 0.389,0.161 10 45° 4.342,3.015 4.731,3.176 0.389,0.161 10 60° 1.248,3.365 1.637,3.527 0.389,0.161 10 30° 1.464,3.163 1.853,3.325 0.389,0.161 10 45° 1.751,3.015 2.139,3.176 0.389,0.161 10 60°

NOTICE:
·

Repair the seat while checking the seating position.

·

Releasing the seat cutter pressure gradually helps to make the intake valve seat faces smoother.



HINT:

Select an appropriate cutter by referring to the following chart.


Contact position Cutter to be selected
A in the illustration If the valve face position is high, use a 30° valve seat cutter in order to grind the surface so that the contact surface between the valve and the valve seat is at a standard value.
B in the illustration If the valve face position is low, use a 60° valve seat cutter in order to grind the surface so that the contact surface between the valve and the valve seat is at a standard value.
C in the illustration If the valve face position is centered, use a 30°and 60° valve seat cutter in order to grind the surface so that the contact surface between the valve and the valve seat is at a standard value.


e.

Hand-lap the valve and valve seat with an abrasive compound.


Hide 3.REPAIR VALVE

a.
A278781E03
1.479,1.167 1.479,1.552 false 3.208,1.333 2.917,1.573 false 2.771,1.583 2.969,1.771 0.198,0.188 10 false *b 1.396,1.583 1.594,1.771 0.198,0.188 10 false *a

Apply a light layer of engine oil to the valve stem, and a small amount of an abrasive compound uniformly to the valve face.

Text in Illustration
*a Valve stem
*b Valve face

HINT:
·

Do not apply the abrasive compound more than necessary.

·

Do not apply the abrasive compound to the valve stem as the valve stem may be affected.




b.

Slowly insert the valve stem into the valve guide bush and lap the valve and valve seat.

HINT:
·

Lift the valve and strike the valve on the valve seat 2 times, and slightly rotate the valve. Repeat this set.

·

The contact surface between the valve and the valve seat may become larger than the standard value, therefore, ensure that the valve is not continuously lapped by rotating while seated in the valve seat.

·

While lapping, ensure that the valve is not removed from the valve guide bush by lifting too much.




c.

After lapping, completely remove the abrasive compound.

NOTICE:

Be sure to completely remove the abrasive compound as the remained compound could cause engine troubles.



d.

Check the valve seating position and width.