Home › Engine / Hybrid System › FA20 (ENGINE MECHANICAL) › CYLINDER BLOCK › 2012.03–2016.06
RM2090E _51 Engine / Hybrid System _060666 FA20 ENGINE MECHANICAL _0297498 CYLINDER BLOCK A

FA20 ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 11431A 1.INSTALL NO. 1 CYLINDER BLOCK TIGHT PLUG

NOTICE:
·

Place wooden blocks wrapped in a cloth under the cylinder block and stabilize the cylinder block during servicing.

·

Place a cloth to avoid scratching the mating surface of the cylinder block during servicing.



A279611E01
0.173,1.622 0.409,1.838 0.236,0.216 10 *b 0.173,0.075 0.409,0.291 0.236,0.216 10 *a

Text in Illustration
*a for Bank 1
*b for Bank 2

a.

Apply seal packing to the threaded portion of the No. 1 cylinder block tight plugs and install them to the cylinder block (for bank 1) and cylinder block (for bank 2).

Seal packing:

Three Bond 1105 or equivalent


Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)

NOTICE:

Before applying seal packing, degrease the No. 1 cylinder block tight plugs and thread holes of the cylinder block (for bank 1) and cylinder block (for bank 2).



Hide 11401R 2.INSTALL CRANKSHAFT SENSOR HOLDER ASSEMBLY

A278796

a.

Install the crankshaft sensor holder assembly to the cylinder block (for bank 2) with the 2 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 11271J 3.INSTALL CYLINDER BLOCK PLATE

A279368

a.

Install the cylinder block plate to the cylinder block (for bank 2) with the 5 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 12270H 4.INSTALL OIL SEPARATOR COVER

a.
A279367E01
2.307,1.816 2.486,1.978 0.179,0.163 10 *a 1.904,1.491 2.272,1.859 false

Using a sealer gun, apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Three Bond 1217G, 1217H or equivalent


Text in Illustration
*a φ3.5 to 5.0 mm (0.138 to 0.197 in.)

NOTICE:
·

Clean and degrease the contact surface.

·

Install the oil separator cover within 5 minutes of applying seal packing.




b.
A279366E02
1.438,1.927 1.635,2.135 0.198,0.208 10 false 1 0.885,1.854 1.083,2.063 0.198,0.208 10 false 3 2.24,1.76 2.438,1.969 0.198,0.208 10 false 6 2.323,0.521 2.521,0.729 0.198,0.208 10 false 7 1.521,0.594 1.719,0.802 0.198,0.208 10 false 5 0.896,0.573 1.094,0.781 0.198,0.208 10 false 4 0.323,0.427 0.521,0.635 0.198,0.208 10 false 2

Tight the 7 bolts in the order shown in the illustration to install the oil separator cover to the cylinder block (for bank 1).

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 5.INSTALL O-RING

a.
A279377

Attach a new O-ring to the cylinder block (for bank 2).


Hide 11711 6.INSTALL CRANKSHAFT BEARING

a.
A279378E03
0.854,3.948 0.854,4.417 true 1.281,3.438 1.646,2.792 1.646,2.792 2.094,3.438 true 2.5,3.948 2.135,4.406 2.135,4.406 1.688,3.948 true 1.635,1.625 1.281,2.167 1.281,2.167 0.823,1.635 true 1.26,1.104 1.615,0.458 1.615,0.458 2.073,1.104 true 2.448,1.615 2.448,2.167 true 0.177,2.177 0.375,2.354 0.198,0.177 10 false *b 0.177,0.115 0.375,0.292 0.198,0.177 10 false *a 0.781,4.438 0.958,4.615 0.177,0.177 10 false *3 2.375,2.188 2.552,2.365 0.177,0.177 10 false *3 1.583,2.604 1.771,2.792 0.188,0.188 10 false *2 1.552,0.26 1.729,0.438 0.177,0.177 10 false *2 2.083,4.438 2.26,4.615 0.177,0.177 10 false *1 1.198,2.188 1.375,2.365 0.177,0.177 10 false *1

Apply engine oil to the crankshaft bearing, and install them to the cylinder block (for bank 1) and cylinder block (for bank 2).

Text in Illustration
*1 No. 1 and No. 3 Bearings (with groove)
*2 No. 2 and No. 4 Bearings (without groove)
*3 No. 5 Bearing
*a for Bank 1
*b for Bank 2

NOTICE:
·

Place a cloth to avoid scratching the mating surface of the cylinder block during servicing.


·

The shapes of the No. 1 and No. 3 bearings are different from those of the No. 2 and No. 4 bearings. Be sure to install them in the right locations.




Hide 13411 7.INSTALL CRANKSHAFT

A279379

a.

Apply engine oil to the crankshaft journals and place the crankshaft on the cylinder block (for bank 2).


Hide 11401 8.INSTALL CYLINDER BLOCK SUB-ASSEMBLY (for Bank 1)

a.

Using a sealer gun, apply seal packing to the mating surface of the cylinder block sub-assembly (for bank 1) as shown in the illustration.

Seal packing:

Three Bond 1217G, 1217H or equivalent


U146735E03
0.448,0.917 0.271,1.438 true 1.156,2.427 2.052,1.917 true 1.156,2.427 1.302,2.01 true 1.146,2.427 0.958,2.01 true 0.583,2 1.156,2.427 true 1.646,2 1.156,2.427 true 1.146,0.698 2.021,1.198 true 1.135,0.698 1.292,1.115 true 1.135,0.698 0.948,1.115 true 0.573,1.125 1.135,0.698 true 1.635,1.115 1.146,0.688 true 5.792,2.25 6.052,2.5 true 5.833,1.375 6.104,1.625 true 5.813,0.51 6.083,0.76 true 0.396,0.365 0.583,0.563 0.188,0.198 10 false *i 4.281,1.125 4.469,1.354 0.188,0.229 10 false *j 0.198,1.438 0.375,1.615 0.177,0.177 10 false *a 1.76,0.896 1.906,1.063 0.146,0.167 10 false A 3.156,1.573 3.302,1.74 0.146,0.167 10 false C 3.792,1.698 3.938,1.865 0.146,0.167 10 false B 3.625,1.125 3.771,1.292 0.146,0.167 10 false B 3.802,1.906 3.948,2.073 0.146,0.167 10 false B 3.865,1.333 4.01,1.5 0.146,0.167 10 false B 2.083,0.656 2.229,0.823 0.146,0.167 10 false A 1.063,2.479 1.24,2.656 0.177,0.177 10 false *b 1.063,0.521 1.24,0.698 0.177,0.177 10 false *b 2.448,0.375 2.625,0.552 0.177,0.177 10 false *c 3.344,1.438 3.49,1.604 0.146,0.167 10 false C 5.021,2.073 5.313,2.24 0.292,0.167 10 false C-C 5.385,1.865 5.573,2.042 0.188,0.177 10 false *g 6.073,2.5 6.26,2.677 0.188,0.177 10 false *h 6.063,2.125 6.25,2.302 0.188,0.177 10 false *f 5.021,1.198 5.313,1.365 0.292,0.167 10 false B-B 5.427,0.979 5.615,1.156 0.188,0.177 10 false *d 6.125,1.625 6.313,1.802 0.188,0.177 10 false *h 6.073,1.24 6.26,1.417 0.188,0.177 10 false *f 5.021,0.333 5.313,0.5 0.292,0.167 10 false A-A 5.417,0.125 5.604,0.302 0.188,0.177 10 false *d 6.094,0.76 6.281,0.938 0.188,0.177 10 false *h 6.052,0.385 6.24,0.563 0.188,0.177 10 false *e

Text in Illustration
*a φ3.5 to 4.5 mm (0.138 to 0.177 in.) *b φ0.5to 1.5 mm (0.0197 to 0.0591 in.)
*c Range of A-A *d Within φ1.0 mm (0.039 in.)
*e φ2.7 to 3.7 mm (0.106 to 0.146 in.) *f φ3.5 to 4.5 mm (0.138 to 0.177 in.)
*g φ2.0 mm (0.079 in.) *h Chamfer edge
*i 36.0 mm (1.417 in.) *j 2.5 mm (0.098 in.)

NOTICE:
·

Do not let the seal packing overflow to the oil passage or crankshaft bearing because engine seizure may result.

·

Clean and degrease the contact surface.

·

Install the cylinder block sub-assembly (for bank 1) within 5 minutes of applying seal packing.




b.

Place the cylinder block sub-assembly (for bank 1) to the cylinder block sub-assembly (for bank 2).


c.

Apply engine oil to the washers and cylinder block bolt threads.

NOTICE:

To prevent engine oil from entering into the water jacket, do not apply a large amount.



d.
U146733E03
0.802,1.76 0.979,1.927 0.177,0.167 10 false 10 2.469,0.573 2.583,0.74 0.115,0.167 10 false 9 0.854,0.656 0.969,0.823 0.115,0.167 10 false 8 2.448,1.854 2.563,2.021 0.115,0.167 10 false 7 1.271,0.573 1.385,0.74 0.115,0.167 10 false 6 2.052,1.833 2.167,2 0.115,0.167 10 false 5 1.26,1.813 1.375,1.979 0.115,0.167 10 false 4 2.063,0.573 2.177,0.74 0.115,0.167 10 false 3 1.656,1.823 1.771,1.99 0.115,0.167 10 false 2 1.656,0.563 1.771,0.729 0.115,0.167 10 false 1

Using a 12 mm socket wrench, tighten the 10 bolts in the order shown in the illustration.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

When tightening the bolts, hold the cylinder block sub-assembly (for bank 2) while not holding the cylinder block sub-assembly (for bank 1) to ensure the joint accuracy of the cylinder blocks.



e.
U146734E03
1.615,0.552 1.792,0.719 0.177,0.167 10 false 10 1.656,1.833 1.771,2 0.115,0.167 10 false 9 2.073,0.563 2.188,0.729 0.115,0.167 10 false 8 1.281,1.833 1.396,2 0.115,0.167 10 false 7 2.052,1.813 2.167,1.979 0.115,0.167 10 false 6 1.26,0.563 1.375,0.729 0.115,0.167 10 false 5 2.458,1.833 2.573,2 0.115,0.167 10 false 4 0.854,0.656 0.969,0.823 0.115,0.167 10 false 3 2.448,0.573 2.563,0.74 0.115,0.167 10 false 2 0.844,1.729 0.958,1.896 0.115,0.167 10 false 1

Using a 12 mm socket wrench, loosen the 10 bolts by 180 ° in the order shown in the illustration.

NOTICE:

When loosening the bolts, hold the cylinder block sub-assembly (for bank 2) while not holding the cylinder block sub-assembly (for bank 1) to ensure the joint accuracy of the cylinder blocks.



f.
U146733E03
0.802,1.76 0.979,1.927 0.177,0.167 10 false 10 2.469,0.573 2.583,0.74 0.115,0.167 10 false 9 0.854,0.656 0.969,0.823 0.115,0.167 10 false 8 2.448,1.854 2.563,2.021 0.115,0.167 10 false 7 1.271,0.573 1.385,0.74 0.115,0.167 10 false 6 2.052,1.833 2.167,2 0.115,0.167 10 false 5 1.26,1.813 1.375,1.979 0.115,0.167 10 false 4 2.063,0.573 2.177,0.74 0.115,0.167 10 false 3 1.656,1.823 1.771,1.99 0.115,0.167 10 false 2 1.656,0.563 1.771,0.729 0.115,0.167 10 false 1

Using a 12 mm socket wrench, tighten the 10 bolts in the order shown in the illustration.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

When tightening the bolts, hold the cylinder block sub-assembly (for bank 2) while not holding the cylinder block sub-assembly (for bank 1) to ensure the joint accuracy of the cylinder blocks.



g.
U146833E03
2.26,0.385 2.375,0.552 0.115,0.167 10 false 4 1.083,0.396 1.198,0.563 0.115,0.167 10 false 1 1.125,2 1.24,2.167 0.115,0.167 10 false 3 2.229,2 2.344,2.167 0.115,0.167 10 false 2

Using a 12 mm socket wrench, loosen the 4 bolts by 180 ° in the order shown in the illustration.

NOTICE:

When loosening the bolts, hold the cylinder block sub-assembly (for bank 2) while not holding the cylinder block sub-assembly (for bank 1) to ensure the joint accuracy of the cylinder blocks.



h.
U146834E03
1.104,0.406 1.219,0.573 0.115,0.167 10 false 4 2.24,2 2.354,2.167 0.115,0.167 10 false 3 1.115,2 1.229,2.167 0.115,0.167 10 false 2 2.26,0.385 2.375,0.552 0.115,0.167 10 false 1

Using a 12 mm socket wrench, tighten the 4 bolts in the order shown in the illustration.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)

NOTICE:

When tightening the bolts, hold the cylinder block sub-assembly (for bank 2) while not holding the cylinder block sub-assembly (for bank 1) to ensure the joint accuracy of the cylinder blocks.



i.
U190107E01
1.445,1.154 1.564,1.322 0.119,0.167 10 4 2.11,1.951 2.229,2.118 0.119,0.167 10 3 1.008,1.951 1.127,2.118 0.119,0.167 10 2 1.53,0.325 1.649,0.492 0.119,0.167 10 1 0.198,0.892 0.374,1.059 0.177,0.166 10 *1 0.983,0.979 0.386,0.979 false

Using a 12 mm socket wrench and an angle gauge, tighten the 4 bolts by additional 60° in the order shown in the illustration.

Text in Illustration
*1 Temporary Bolt

NOTICE:

When tightening the bolts, hold the cylinder block sub-assembly (for bank 2) while not holding the cylinder block sub-assembly (for bank 1) to ensure the joint accuracy of the cylinder blocks.


HINT:

Temporarily install the appropriate bolt for the angle gauge if necessary.



j.
U146835E03
1.667,0.333 1.781,0.5 0.115,0.167 10 false 6 1.677,2 1.813,2.146 0.135,0.146 10 false 5 2.458,0.344 2.573,0.51 0.115,0.167 10 false 4 0.854,1.948 0.969,2.115 0.115,0.167 10 false 3 2.469,2 2.615,2.156 0.146,0.156 10 false 2 0.844,0.406 0.958,0.573 0.115,0.167 10 false 1

Using a 12 mm socket wrench, loosen the 6 bolts by 180 ° in the order shown in the illustration.

NOTICE:

When loosening the bolts, hold the cylinder block sub-assembly (for bank 2) while not holding the cylinder block sub-assembly (for bank 1) to ensure the joint accuracy of the cylinder blocks.



k.
U146836E01
0.863,0.393 0.982,0.560 0.119,0.167 10 6 2.478,1.981 2.602,2.124 0.124,0.143 10 5 0.874,1.93 0.993,2.097 0.119,0.167 10 4 2.468,0.309 2.587,0.477 0.119,0.167 10 3 1.681,1.981 1.806,2.124 0.124,0.143 10 2 1.677,0.318 1.796,0.485 0.119,0.167 10 1

Using a 12 mm socket wrench, tighten the 6 bolts in the order shown in the illustration.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)

NOTICE:

When tightening the bolts, hold the cylinder block sub-assembly (for bank 2) while not holding the cylinder block sub-assembly (for bank 1) to ensure the joint accuracy of the cylinder blocks.



l.
U190108E01
0.848,0.537 0.967,0.704 0.119,0.167 10 6 2.282,1.97 2.413,2.122 0.132,0.152 10 5 0.872,1.946 0.991,2.113 0.119,0.167 10 4 2.667,0.448 2.786,0.615 0.119,0.167 10 3 1.57,1.97 1.718,2.121 0.148,0.151 10 2 1.495,0.254 1.614,0.421 0.119,0.167 10 1 0.378,1.49 0.552,1.658 0.174,0.167 10 *1 1.237,1.044 0.567,1.545 false

Using a 12 mm socket wrench and an angle gauge, tighten the 6 bolts by additional 60° in the order shown in the illustration.

Text in Illustration
*1 Temporary Bolt

NOTICE:

When tightening the bolts, hold the cylinder block sub-assembly (for bank 2) while not holding the cylinder block sub-assembly (for bank 1) to ensure the joint accuracy of the cylinder blocks.


HINT:

Temporarily install the appropriate bolt for the angle gauge if necessary.



m.
A279375

Tighten the 5 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

After tightening, if the seal packing is squeezed out in the seal surface area of the chain cover and oil pan sub-assembly, completely remove it. Seal packing on the chamfer area, however, should not be removed.



Hide 11401L 9.INSTALL REAR ENGINE OIL SEAL

a.

Apply a light coat of engine oil to a new rear engine oil seal inner periphery and outer periphery.


b.
A276049E01
1.9,1.407 1.378,1.701 1.378,1.701 1.272,1.456 false 1.226,1.747 1.524,1.897 0.297,0.151 10 SST 1.755,2.718 2.029,2.49 false 2.061,2.385 2.358,2.536 0.297,0.151 10 SST

Using SST and a hammer, tap in the rear engine oil seal uniformly to the position shown in the illustration.

SST
09223-15030  
09950-70010  (09951-07150)

Oil seal tap-in depth:

0 to 1.0 mm (0 to 0.039 in.) from the cylinder block surface


NOTICE:
·

Do not tap in the rear engine oil seal at an angle.

·

Remove the engine oil from the crankshaft.

·

Do not tap in the rear engine oil seal more than necessary.




Hide 11401 10.INSTALL CYLINDER BLOCK SUB-ASSEMBLY

a.

Mount the cylinder block sub-assembly onto an engine stand.


Hide 13101 11.INSTALL PISTON WITH PIN SUB-ASSEMBLY

a.
A281475E03
1.76,1.021 2.073,1.708 true 2.021,1.75 2.313,1.99 0.292,0.24 10 false *1

Using a screwdriver with its tip wrapped in protective tape, install the piston pin hole snap ring on one end of the piston.

Text in Illustration
*1 Protective Tape

HINT:
·
A279396E01
2.753,1.545 2.936,1.714 0.184,0.169 10 *1 0.174,1.716 0.358,1.886 0.184,0.169 10 *b 0.174,0.17 0.358,0.339 0.184,0.169 10 *a 1.936,1.168 2.726,1.636 2.726,1.636 1.958,2.525 false

Make sure that the piston pin hole snap ring is firmly attached into the piston pin hole snap ring groove.

·

After installing the piston pin hole snap ring, rotate the piston pin hole snap ring so that its end part and the cutout portion of the piston pin hole snap ring groove do not match.



Text in Illustration
*1 Piston Pin Hole Snap Ring
*a Correct
*b Incorrect


b.
A279397E03
0.938,1.125 1.063,1.49 false 0.333,2.333 0.167,2.708 false 0.031,1.427 0.24,1.625 0.208,0.198 10 false *b 0.031,0.125 0.24,0.323 0.208,0.198 10 false *a 1,1.5 1.208,1.698 0.208,0.198 10 false *1 0.094,2.719 0.302,2.917 0.208,0.198 10 false *1

Set the piston to the connecting rod.

Text in Illustration
*1 Front Mark
*a for Bank 1
*b for Bank 2

HINT:

Align the front mark of the piston and the direction of the connecting rod correctly as shown in the illustration.



c.

Apply engine oil to the piston pin and install it to the piston.


d.
A283333E06
1.427,0.854 1.198,1.438 true 1.115,1.448 1.365,1.677 0.25,0.229 10 false *1

Using a screwdriver with its tip wrapped in protective tape, install the piston pin hole snap ring to the piston.

Text in Illustration
*1 Protective Tape

HINT:
·
A279398E01
2.579,1.718 2.836,1.963 0.257,0.245 10 *1 0.173,1.718 0.430,1.963 0.257,0.245 10 *b 0.173,0.171 0.430,0.416 0.257,0.245 10 *a 1.909,1.119 2.544,1.804 2.544,1.804 1.908,2.59 false

Make sure the piston pin hole snap ring is firmly attached into the piston pin hole snap ring groove.

·

After installing the piston pin hole snap ring, rotate the piston pin hole snap ring so that its end part and the cutout portion of the piston pin hole snap ring groove do not match.



Text in Illustration
*1 Piston Pin Hole Snap Ring
*a Correct
*b Incorrect


Hide 13011 12.INSTALL PISTON RING SET

a.

Install the oil ring expander, lower oil ring side rail and upper oil ring side rail in order by hand.

HINT:

The oil ring consists of the 2 oil ring side rails and oil ring expander.



b.

Set the oil ring expander ends at the location B in the illustration.


c.
A279389E02
2.229,1.052 2.635,0.76 true 0.969,1.385 0.656,1.802 false 2.938,2.979 3.01,3.375 false 2.01,3.708 2.25,3.875 false 1.792,2.729 2.188,2.885 false 1.781,3.188 2.49,3.063 false 1.75,0.094 1.885,0.26 0.135,0.167 10 false B 2.302,3.844 2.49,4.031 0.188,0.188 10 false A 2.26,1.885 2.396,2.052 0.135,0.167 10 false A 0.75,1.26 0.938,1.469 0.188,0.208 10 false C 2.958,3.417 3.146,3.604 0.188,0.188 10 false *2 2.635,0.594 2.823,0.781 0.188,0.188 10 false *1 0.552,1.813 0.74,1.99 0.188,0.177 10 false *a 1.604,3.115 1.792,3.302 0.188,0.188 10 false *4 1.594,2.635 1.781,2.823 0.188,0.188 10 false *3

Hook the stoppers at the rail ends of the lower oil ring side rail into cutout A of the piston and the oil ring expander as shown in the illustration.


d.

Align the rail ends of the upper oil ring side rail within the range C and hook the stopper into the oil ring expander.


e.

Using a piston ring expander, install the No. 2 compression ring and No. 1 compression ring in order.

Text in Illustration
*1 Front Mark
*2 Lower Oil Ring Side Rail
*3 Expander
*4 Cutout
*a 0 to 20°


f.
A284976E01
1.579,0.043 2.037,0.213 0.458,0.170 10 180° 3.008,1.116 3.150,1.296 0.142,0.180 10 B 0.43,1.116 0.572,1.296 0.142,0.180 10 A

Set the No. 1 compression ring ends at the location A or B in the illustration.

HINT:

The No. 1 compression ring ends can be set either at A or B.



g.

Set the No. 2 compression ring ends at the location A or B, that is 180° opposite of those of the No. 1 compression ring.


h.

Check that the piston rings and oil rings are correctly set.


Hide 13.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Operate the engine stand so that the oil pan side faces upward.


b.
A281479E01
2.674,1.5 2.875,1.662 0.201,0.162 10 *a 2.456,0.489 2.756,1.481 false

Install the connecting rod bearings to the connecting rod and connecting rod cap. <*1>

Text in Illustration
*a Claw


c.

Check that the piston rings and oil rings are correctly set.


d.

Apply engine oil to the piston and inside the cylinder bore.


e.
A279392E03
1.375,0.552 0.406,0.552 true 0.219,0.458 0.417,0.688 0.198,0.229 10 false *1

Turn the crankshaft so that the crank pin is positioned at TDC.

Text in Illustration
*1 Crank Pin


f.
A279393

Using a piston ring compressor, compress the piston rings and insert the piston with connecting rod into the cylinder block.

NOTICE:
·

When inserting the piston with connecting rod, be careful not to scratch the cylinder bore or crank pin by connecting the rod edge.

·

Be careful not to apply too much impact when inserting to prevent the connecting rod bearing from falling off.



HINT:

Face the front mark toward the front of the engine.



g.

Apply engine oil to the seating face of the connecting rod cap and threads of the connecting rod cap bolts.


h.
A279394E03
1.76,2.302 0.823,2.813 true 2.375,3.094 1.865,2.292 true 0.615,2.75 0.854,2.979 0.24,0.229 10 false *1 2.333,3.125 2.573,3.313 0.24,0.188 10 false *2

While pushing the piston top, turn the crankshaft to position the crankshaft pin and connecting rod large end as shown in the illustration, and then attach the connecting rod cup with 2 new connecting rod cap bolts.

Text in Illustration
*1 Connecting Rod
*2 Crankshaft Pin

HINT:
·
A281041E03
1.313,3.292 1.51,3.573 1.51,3.573 1.719,3.292 true 1.427,3.615 1.615,3.792 0.188,0.177 10 false *1

Each connecting rod has its own mating cap. Make sure that they are assembled correctly by checking their matching symbols.

·

Use new connecting rod cap bolts.

·

Turn the crankshaft counterclockwise when installing the No. 1 or No. 3 piston with connecting rod, and turn the crankshaft clockwise when installing the No. 2 or No. 4 piston with connecting rod.



Text in Illustration
*1 Matching Symbol


i.
U146842E01
1.589,0.444 1.716,0.609 0.128,0.165 10 1 2.151,0.444 2.279,0.609 0.128,0.165 10 2 1.378,1.278 1.506,1.443 0.128,0.165 10 2 1.913,1.283 2.041,1.448 0.128,0.165 10 1 1.278,2.999 1.406,3.164 0.128,0.165 10 2 1.8,3 1.927,3.165 0.128,0.165 10 1 1.485,3.998 1.613,4.163 0.128,0.165 10 1 2.027,3.976 2.155,4.142 0.128,0.165 10 2 0.2,2.562 0.429,2.779 0.229,0.217 10 *b 0.2,0.293 0.429,0.510 0.229,0.217 10 *a

Using a "TORX" socket wrench E14, tighten the 2 connecting rod cup bolts in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*a No. 1 and No. 4
*b No. 2 and No. 3


j.

Retighten the 2 connecting rod cup bolts in the same order as above. <*2>

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


k.

In the same procedures from <*1> to <*2>, install the No. 2, No. 3 and No. 4 piston with connecting rods.


l.
U190150E01
1.603,0.437 1.731,0.602 0.128,0.165 10 1 2.137,0.442 2.265,0.608 0.128,0.165 10 2 1.384,1.283 1.512,1.448 0.128,0.165 10 2 1.933,1.298 2.061,1.464 0.128,0.165 10 1 1.278,2.998 1.406,3.164 0.128,0.165 10 2 1.804,2.996 1.932,3.161 0.128,0.165 10 1 1.485,3.998 1.613,4.163 0.128,0.165 10 1 2.027,3.976 2.155,4.142 0.128,0.165 10 2 0.172,0.271 0.510,0.575 0.338,0.304 10 *a 0.172,2.532 0.510,2.836 0.338,0.304 10 *b 3.001,1.915 3.204,2.121 0.203,0.206 10 *1 2.466,2.015 2.969,2.015 false

Using a "TORX" socket wrench E14 and an angle gauge, tighten the connecting rod cup bolts for the No. 1 to No. 4 piston with connecting rods by additional 92.5°.

HINT:

Temporarily install the appropriate bolt for the angle gauge if necessary.


Text in Illustration
*1 Temporary Bolt
*a No. 1 and No. 4
*b No. 2 and No. 3


m.

Check that the crankshaft can be turned smoothly.