Home › Engine / Hybrid System › FA20 FUEL › FUEL INJECTOR(for Port Injection)
RM2090E _51 Engine / Hybrid System _060667 FA20 FUEL _0297500 FUEL INJECTOR(for Port Injection) G

FA20 FUEL  FUEL INJECTOR(for Port Injection)  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.
A281862E01
0.245,0.104 0.401,0.285 0.156,0.181 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 12 Ω


Text in Illustration
*a Component without harness connected
(Fuel Injector Assembly)

If the resistance is not as specified, replace the fuel injector assembly.


b.

Inspect the injection volume.

CAUTION:

This test involves high-pressure fuel and electricity. Take all precautions regarding safe handling of both the fuel and the electricity. Perform this test in a safe area, and avoid any sparks or flames. Do not smoke.



c.
A281833

Disconnect the fuel tube. (for metal type)


d.
A279753

Disconnect the fuel hose. (for clamp type)


e.
A281889E03
0.906,1.531 0.906,1.833 false 1.729,1.26 1.729,1.552 false 2.583,0.917 2.583,1.208 false 0.833,1.844 1.01,2.021 0.177,0.177 10 false *1 1.656,1.573 1.833,1.75 0.177,0.177 10 false *2 2.51,1.229 2.688,1.406 0.177,0.177 10 false *3

Connect SST (hose) to the fuel pipe (vehicle side) with SST (hose band).

SST
09268-31014  (09268-41700, 95336-08070)

Text in Illustration
*1 SST
(Hose)
*2 SST
(Hose Band)
*3 Fuel Pipe (Vehicle Side)


f.

Install the O-ring to the fuel injector assembly.


g.
A282568E03
1.5,0.073 0.969,0.073 false 1.896,0.25 2.354,0.25 false 1.458,0.677 0.969,0.677 false 1.656,1.385 1.885,1.385 false 2.531,1.198 2.938,1.198 false 1.49,2.052 0.979,2.052 false 0.802,0.021 0.958,0.198 0.156,0.177 10 false *1 0.802,0.604 0.958,0.781 0.156,0.177 10 false *3 0.802,1.969 0.958,2.146 0.156,0.177 10 false *6 2.406,0.167 2.563,0.344 0.156,0.177 10 false *2 1.938,1.292 2.094,1.469 0.156,0.177 10 false *4 2.979,1.094 3.135,1.271 0.156,0.177 10 false *5

Install SST and vinyl tube to the fuel injector assembly.

SST
09268-31014  (09268-41141, 09268-41410, 09268-41700, 95336-08070)

Text in Illustration
*1 SST
(Hose)
*2 SST
(Hose Band)
*3 SST
(Adapter)
*4 O-ring
*5 SST
(Clamp)
*6 Vinyl Tube


h.
A282569E03
1.302,0.583 0.979,0.25 0.979,0.25 0.594,0.25 false 1.583,0.917 0.573,0.917 false 1.969,1.271 2.604,1.271 false 0.417,0.177 0.573,0.354 0.156,0.177 10 false *1 0.375,0.823 0.531,1 0.156,0.177 10 false *2 2.635,1.198 2.792,1.375 0.156,0.177 10 false *3

Tie SST (clamp and adapter) together with SST (tie band) as shown in the illustration.

SST
09268-31014  (09268-41141, 09268-41410, 09268-41800)

Text in Illustration
*1 SST
(Tie Band)
*2 SST
(Adapter)
*3 SST
(Clamp)


i.
A282570E03
1.604,0.354 1.885,1.302 true 0.896,1.313 1.052,1.49 0.156,0.177 10 false *a 1.823,1.313 1.979,1.49 0.156,0.177 10 false *1

Put the injector into a graduated cylinder.

SST
09842-30090  

Text in Illustration
*1 SST (Wire)
*a Connect

CAUTION:

Install a strong rubber tube onto the injector to prevent gasoline from splashing.



j.

Operate the fuel pump (turn the ignition switch to ON).


k.

Connect SST (wire) to the injector and the battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each injector 2 or 3 times.

Standard injection volume:

84 to 103 cc (5.1 to 6.3 cu.in.) per 15 seconds


Difference between each injector:

19 cc (1.2 cu.in.) or less


NOTICE:
·

Make sure that SST (EFI inspection wire I) is securely connected.

·

Always turn on and off the voltage on the battery side, not on the fuel pump side.



If the injection volume is not as specified, replace the fuel injector assembly.


l.

Check for leakage.

i.
A281865

In the condition above, disconnect the tester probes of SST (wire) from the battery and check for fuel leakage from the fuel injector assembly.

Standard fuel drop:

1 drop or less in 22 minutes


If there is excessive leakage, replace the fuel injector assembly.