Home › Engine / Hybrid System › FA20 FUEL › FUEL INJECTOR(for Port Injection) › from 2016.06
RM2090E _51 Engine / Hybrid System _060667 FA20 FUEL _0297500 FUEL INJECTOR(for Port Injection) A

FA20 FUEL  FUEL INJECTOR(for Port Injection)  REMOVAL  


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 17764D 3.REMOVE CHAMBER ASSEMBLY

Hide 23261A 5.REMOVE INJECTOR COVER (for Bank 1)

a.
A279751

Disengage the 4 clamps and separate the wire harness from the injector cover (for bank 1).


b.

for Resin Intake Manifold:

i.
A277976

Remove the 2 bolts and injector cover (for bank 1).



c.

for Aluminum Intake Manifold:

i.
A387945

Remove the 2 bolts and disengage the 2 guides, and then remove the injector cover.



Hide 77259D 6.DISCONNECT NO. 1 FUEL HOSE (for Metal Type)

a.
A281447

Using SST, disconnect the No. 1 fuel hose from the fuel delivery pipe sub-assembly (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>PRECAUTION).

SST
SU003-03936  


Hide 77419 7.DISCONNECT NO. 3 FUEL HOSE (for Metal Type)

a.
A281448

Using SST, disconnect the No. 3 fuel hose from the fuel pipe (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>PRECAUTION).

SST
SU003-03936  


Hide 77279G 8.DISCONNECT NO. 2 FUEL HOSE (for Metal Type)

a.
A282016

Remove the clamp and disconnect the No. 2 fuel vapor feed hose from the fuel pipe.


Hide 23261A 9.REMOVE INJECTOR COVER (for Bank 2)

a.
A281164

Remove the bolt and disconnect the wire harness clamp bracket from the injector cover (for bank 2).


b.

for Resin Intake Manifold:

i.
A277981

Remove the 2 bolts and injector cover (for bank 2).



c.

for Aluminum Intake Manifold:

i.
A387943

Remove the 2 bolts and disengage the 2 guides, and then remove the injector cover.



Hide 77259D 10.DISCONNECT NO. 1 FUEL HOSE (for Clamp Type)

a.
A279753

Remove the clamp and disconnect the No. 1 fuel hose.

NOTICE:
·

Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.

·

Be careful not to splash the fuel.

·

Receive the fuel remaining inside the fuel hose with a container.

·

Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.




Hide 23807 11.SEPARATE FUEL DELIVERY PIPE SUB-ASSEMBLY (for Clamp Type)

a.
A279754

Remove the bolt and disconnect the fuel delivery pipe sub-assembly.


b.

Disconnect the No. 2 fuel vapor feed hose and move the fuel delivery pipe sub-assembly toward the front of the vehicle.


Hide 12.REMOVE FUEL DELIVERY PIPE (for Bank 2)

a.
A277982

Disconnect the 2 fuel injector assembly connectors.


b.

Disengage the clamp and separate the wire harness.


c.
A279755

Disconnect the fuel pump assembly connector.


d.
A277984

Disconnect the No. 2 fuel delivery pipe sub-assembly from the fuel delivery pipe (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>PRECAUTION).


e.
A277983

Remove the 2 bolts and fuel delivery pipe.

NOTICE:

When removing the fuel delivery pipe, hold the pipe by both ends and pull it straight upward.



Hide 23255A 13.REMOVE FUEL INJECTOR SEAL (for Bank 2)

a.
A322085

Remove the 2 fuel injector seals.


Hide 14.REMOVE FUEL DELIVERY PIPE (for Bank 1)

a.
A277977

Disconnect the 2 fuel injector assembly connectors.


b.

Disengage the clamp and separate the wire harness.


c.

Disconnect the No. 2 fuel delivery pipe sub-assembly from the fuel delivery pipe (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>PRECAUTION).


d.
A277978

Remove the 2 bolts and fuel delivery pipe.

NOTICE:

When removing the fuel delivery pipe, hold the pipe by both ends and pull it straight upward.



Hide 23255A 15.REMOVE FUEL INJECTOR SEAL (for Bank 1)

a.
A321961

Remove the 2 fuel injector seals.


Hide 23250 16.REMOVE FUEL INJECTOR ASSEMBLY

a.
A277979

A281860E02
1.685,0.213 2.079,0.394 0.394,0.181 10 No. 1

Remove the 4 fuel injector assemblies from the fuel delivery pipe.

NOTICE:

For reinstallation, attach a tag or label to the injector shaft.



b.
A321981E03
1.885,0.281 2.5,0.281 false 1.885,0.542 2.365,0.854 2.365,0.854 2.458,0.854 false 2.563,0.188 2.813,0.406 0.25,0.219 10 false *1 2.5,0.771 2.75,0.99 0.25,0.219 10 false *2

Remove the fuel injector O-ring and fuel injector grommet from the fuel injector assembly.

Text in Illustration
*1 Fuel injector O-ring
*2 Fuel injector grommet