Home › Engine / Hybrid System › FA20 FUEL › FUEL SENDER GAUGE ASSEMBLY
RM2090E _51 Engine / Hybrid System _060667 FA20 FUEL _0297508 FUEL SENDER GAUGE ASSEMBLY G

FA20 FUEL  FUEL SENDER GAUGE ASSEMBLY  INSPECTION  


PROCEDURE

Hide 83320 1.INSPECT FUEL SENDER GAUGE ASSEMBLY

CAUTION:

Take special care of fire.


a.

Inspect to see if there is any damage to the fuel sender gauge assembly.


b.
A280569E03
0.333,0.281 0.542,0.49 0.208,0.208 10 false *1 0.333,1.906 0.542,2.115 0.208,0.208 10 false *3 1,1.542 1.208,1.75 0.208,0.208 10 false *2

Measure the dimensions between the fuel tank seat face and the float center with the float position at F (upper end) and at E (lower end).

Dimensions
Float position F (upper end) to fuel tank seat face 121 to 129 mm (4.764 to 5.079 in.)
Float position E (lower end) to fuel tank seat face 14.7 to 22.7 mm (0.579 to 0.894 in.)

Text in Illustration
*1 Float position F (upper end)
*2 Float position E (lower end)
*3 Fuel tank seat face


c.

Check that the float moves smoothly between F (upper) and E (lower).


d.
A282939E03
0.635,0.135 0.792,0.313 0.156,0.177 10 false *a 1.625,1.875 1.781,2.052 0.156,0.177 10 false *c 2.115,0.083 2.271,0.26 0.156,0.177 10 false *b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Float position is F (upper end) 6.5 to 8.5 Ω
Float position is E (lower end) 168 to 172 Ω


Text in Illustration
*a Component without harness connected
(Fuel Sender Gauge Assembly)
*b F (upper end)
*c E (lower end)

If the value is not as specified, replace the fuel sender gauge assembly.


Hide 83320B 2.INSPECT NO. 2 FUEL SENDER GAUGE ASSEMBLY

CAUTION:

Take special care of fire.


a.

Inspect to see if there is any damage to the No. 2 fuel sender gauge assembly.


b.
A280576E03
0.635,0.479 0.844,0.677 0.208,0.198 10 false *1 0.635,1.594 0.844,1.792 0.208,0.198 10 false *3 1.24,1.344 1.448,1.542 0.208,0.198 10 false *2

Measure the dimensions between the fuel tank seat face and the float center with the float position at F (upper end) and at E (lower end).

Dimensions
Float position F (upper end) to fuel tank seat face 150.3 to 158.3 mm (5.917 to 6.232 in.)
Float position E (lower end) to fuel tank seat face 0.7 to 8.7 mm (0.028 to 0.343 in.)

Text in Illustration
*1 Float position F (upper end)
*2 Float position E (lower end)
*3 Fuel tank seat face


c.

Check that the float moves smoothly between F (upper) and E (lower).


d.
A280577E02
0.475,0.004 0.755,0.241 0.280,0.238 10 *a 1.781,0.127 1.946,0.276 0.164,0.148 10 *b 1.737,1.373 1.901,1.522 0.164,0.148 10 *c

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Float position is F (upper end) 5.5 to 9.5 Ω
Float position is E (lower end) 236 to 244 Ω


Text in Illustration
*a Component without harness connected
(No. 2 Fuel Sender Gauge Assembly)
*b F (upper end)
*c E (lower end)

If the value is not as specified, replace the fuel sender gauge assembly.