Home › Engine / Hybrid System › FA20 FUEL › FUEL SENDER GAUGE ASSEMBLY
RM2090E _51 Engine / Hybrid System _060667 FA20 FUEL _0297508 FUEL SENDER GAUGE ASSEMBLY A

FA20 FUEL  FUEL SENDER GAUGE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 71470S 3.REMOVE SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY LH

Hide 71460S 4.REMOVE SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY RH

Hide 58311F 5.REMOVE NO. 2 REAR FLOOR SERVICE HOLE COVER

Hide 77020A 6.REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

Hide 83320 7.REMOVE FUEL SENDER GAUGE ASSEMBLY

a.
A278283

Disconnect the fuel sender gauge assembly connector.


b.

Disconnect the fuel pump harness from the 2 clamps.


c.
A281943E02
2.156,0.969 2.323,0.792 true 2.323,0.635 2.448,0.802 0.125,0.167 10 false A

Disconnect the fuel pump harness from the clamp.


d.

Push the claw labeled A of the fuel sender gauge assembly, and then pull up the fuel sender gauge assembly to remove it.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.


Text in Illustration
V100135

Push
V100136

Pull up


Hide 58311E 8.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A277986

Remove the rear floor service hole cover.


b.
A277987

Disconnect the fuel tank return tube connector.


Hide 77204A 9.REMOVE FUEL TANK RETURN TUBE

a.
A291071E03
2.99,1.125 2.427,0.5 true 3.021,1.052 3.354,1.313 0.333,0.26 10 false SST

A291075E01
2.574,0.215 2.794,0.420 0.220,0.205 10 *a 1.73,0.973 2.539,0.39 false

Temporarily install SST to the fuel pump gauge retainer.

SST
09808-14030  (09808-01010, 09808-01020, 09808-01030, 09808-01050)
09808-01071  

NOTICE:

Do not apply a claw of SST at the marked part.


Text in Illustration
*a Marked Part

HINT:
·

Be sure to use SST (claws) as shown in the illustration.

·

Engage SST (claws) securely with the fuel pump gauge retainer ribs to secure SST.




b.

While securely pressing SST (claws) against the fuel pump gauge retainer ribs, tighten the 4 bolts.


c.

Install SST (handle).


d.
A291072E01
2.899,0.987 3.246,1.274 0.347,0.287 10 SST 2.433,1.318 2.846,1.117 false

Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing SST, rotate the handle slowly to loosen the fuel pump gauge retainer.

NOTICE:
·

Do not use any tools other than those specified in this operation. Damage to the fuel pump gauge retainer or fuel tank may result.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate and may damage components.

·

Make sure to rotate SST (handle) horizontally. If SST (handle) is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolts) and reinstall SST.




e.

Remove the fuel pump gauge retainer.


f.
A281946

Disengage the clamp and separate the fuel tank vent hose sub-assembly from the fuel tank return tube.


g.

Remove the fuel tank return tube from the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the No. 2 fuel sender gauge assembly.



h.

Remove the gasket from the fuel tank assembly.


Hide 83320B 10.REMOVE NO. 2 FUEL SENDER GAUGE ASSEMBLY

a.
A277989

Disconnect the No. 2 fuel sender gauge assembly connector.


b.

Disconnect the fuel pump harness from the clamp.


c.
A281944E02
1.74,0.854 1.5,0.677 true 1.354,0.573 1.573,0.813 0.219,0.24 10 false A

Push the claw labeled A of the No. 2 fuel sender gauge assembly, and then pull up the No. 2 fuel sender gauge assembly to remove it.

Text in Illustration
V100135

Push
V100136

Pull up