Home › Engine / Hybrid System › FA20 INTAKE / EXHAUST › INTAKE MANIFOLD › from 2016.06
RM2090E _51 Engine / Hybrid System _060669 FA20 INTAKE / EXHAUST _0297515 INTAKE MANIFOLD A

FA20 INTAKE / EXHAUST  INTAKE MANIFOLD  DISASSEMBLY  


PROCEDURE

Hide 89420M 1.REMOVE MANIFOLD ABSOLUTE PRESSURE SENSOR

a.
A391667E02
0.167,0.094 0.635,0.469 0.469,0.375 12 false *A 0.198,2.531 0.667,2.906 0.469,0.375 12 false *B

Remove the bolt and manifold absolute pressure sensor from the intake manifold.

Text in Illustration
*A for Resin Intake Manifold
*B for Aluminum Intake Manifold


b.
A276541

Remove the O-ring from the manifold absolute pressure sensor.


Hide 17650 2.REMOVE PURGE VALVE

a.
A391668E02
0.188,0.094 0.698,0.385 0.51,0.292 12 false *A 0.208,2.292 0.719,2.583 0.51,0.292 12 false *B

Disconnect the No. 1 fuel vapor feed hose from the intake manifold.

Text in Illustration
*A for Resin Intake Manifold
*B for Aluminum Intake Manifold


b.
A391669E02
0.167,0.167 0.552,0.417 0.385,0.25 12 false *A 0.25,2.396 0.635,2.646 0.385,0.25 12 false *B

Remove the nut and purge valve.

Text in Illustration
*A for Resin Intake Manifold
*B for Aluminum Intake Manifold


Hide 55434E 3.REMOVE CAP (for Automatic Transmission)

a.
A285063

Remove the cap from the intake manifold.


Hide 4.REMOVE FUEL DELIVERY PIPE (for Bank 2)

a.

Disconnect the No. 2 fuel delivery pipe sub-assembly from the fuel delivery pipe.

NOTICE:
·

If the connector and pipe are stuck, pinch the fuel delivery pipe by hand and push and pull the connector to disconnect it

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the No. 2 fuel delivery pipe sub-assembly joint contains the O-rings that seal the plug.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcibly bend, twist or turn the nylon tube.

·

If the pipe and connector are stuck together, pinch the tube between your fingers and turn it carefully to free it. Then, disconnect the No. 2 fuel delivery pipe sub-assembly.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the No. 2 fuel delivery pipe sub-assembly.

·

Check that the top hat cannot be pulled out.



A391670E02
0.917,1 0.917,0.729 0.917,0.729 1.083,0.729 false 1.396,1.146 1.396,0.875 1.396,0.875 1.563,0.875 true 1.781,1.094 1.781,0.823 1.781,0.823 1.948,0.823 false 0.469,1.594 0.646,1.594 0.646,1.594 0.646,1.333 true 1.479,1.427 1.479,1.698 1.479,1.698 1.646,1.698 true 1.583,1.688 1.583,1.417 true 2.49,1.406 2.49,1.677 2.49,1.677 2.656,1.677 false 1.667,2.635 1.938,2.49 false 3.823,0.302 4.135,0.5 0.313,0.198 12 false *A 3.958,2.708 4.271,2.906 0.313,0.198 12 false *B 1.135,0.656 1.448,0.854 0.313,0.198 10 false *1 1.594,0.771 1.906,0.969 0.313,0.198 10 false *6 2,0.75 2.313,0.948 0.313,0.198 10 false *2 0.313,1.51 0.625,1.708 0.313,0.198 10 false *5 1.688,1.635 2,1.833 0.313,0.198 10 false *4 2.719,1.594 3.031,1.792 0.313,0.198 10 false *3 1.99,2.385 2.302,2.583 0.313,0.198 10 false *1

Text in Illustration
*A for Resin Intake Manifold *B for Aluminum Intake Manifold
*1 Retainer *2 No. 2 Fuel Delivery Pipe Sub-assembly Connector
*3 Nylon Tube *4 O-ring
*5 fuel delivery pipe *6 Top Hat


b.
A391671E02
0.188,0.188 0.5,0.385 0.313,0.198 12 false *A 0.26,2.417 0.573,2.615 0.313,0.198 12 false *B

Remove the 2 bolts and the fuel delivery pipe from the intake manifold.

Text in Illustration
*A for Resin Intake Manifold
*B for Aluminum Intake Manifold


c.

Remove the 2 O-rings.


Hide 5.REMOVE FUEL DELIVERY PIPE (for Bank 1)

HINT:

Use the same procedure described for the fuel delivery pipe (for bank 2).


Hide 23808 6.REMOVE NO. 2 FUEL DELIVERY PIPE SUB-ASSEMBLY

a.
A391674E02
0.146,0.094 0.458,0.292 0.313,0.198 12 false *A 0.167,2.135 0.479,2.333 0.313,0.198 12 false *B

Disengage the 3 clamps and remove the No. 2 fuel delivery pipe sub-assembly from the intake manifold. (for resin intake manifold)


b.

Disengage the 2 clamps and remove the No. 2 fuel delivery pipe sub-assembly from the intake manifold. (for aluminum intake manifold)

Text in Illustration
*A for Resin Intake Manifold
*B for Aluminum Intake Manifold