Home › Engine / Hybrid System › FA20 STARTING › RELAY
RM2090E _51 Engine / Hybrid System _060672 FA20 STARTING _0297536 RELAY G

FA20 STARTING  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 28300 1.INSPECT ST RELAY

a.
B453162E01
1.729,0.729 1.99,0.729 true 2.646,0.729 2.906,0.729 true 2.521,1.104 2.927,1.104 true 2.531,1.594 2.938,1.594 true 0.25,0.76 0.406,0.958 0.156,0.198 10 false 3 1.198,0.75 1.354,0.948 0.156,0.198 10 false 5 0.25,1.271 0.406,1.469 0.156,0.198 10 false 1 1.198,1.281 1.354,1.479 0.156,0.198 10 false 2 1.573,0.656 1.729,0.854 0.156,0.198 10 false 1 3.01,0.635 3.167,0.833 0.156,0.198 10 false 2 3.01,1 3.167,1.198 0.156,0.198 10 false 5 3.01,1.5 3.167,1.698 0.156,0.198 10 false 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Battery voltage not applied to terminals 1 and 2
Measurement temperature : 20 °C
93.8 to 136.4 kΩ
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the starter relay.


Hide 2.REMOVE INHIBITOR RELAY

a.
B453162E01
1.729,0.729 1.99,0.729 true 2.646,0.729 2.906,0.729 true 2.521,1.104 2.927,1.104 true 2.531,1.594 2.938,1.594 true 0.25,0.76 0.406,0.958 0.156,0.198 10 false 3 1.198,0.75 1.354,0.948 0.156,0.198 10 false 5 0.25,1.271 0.406,1.469 0.156,0.198 10 false 1 1.198,1.281 1.354,1.479 0.156,0.198 10 false 2 1.573,0.656 1.729,0.854 0.156,0.198 10 false 1 3.01,0.635 3.167,0.833 0.156,0.198 10 false 2 3.01,1 3.167,1.198 0.156,0.198 10 false 5 3.01,1.5 3.167,1.698 0.156,0.198 10 false 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Battery voltage not applied to terminals 1 and 2
Measurement temperature : 20 °C
93.8 to 136.4 kΩ
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the starter relay.


Hide 3.INSPECT ST CUT RELAY

a.
A280268E02
2.448,0.552 2.448,0.25 true 2.76,0.698 3.115,0.698 true 1.75,0.719 2.104,0.719 true 1.76,1.115 2.229,1.115 true 1.76,1.604 2.229,1.604 true 1.635,0.625 1.792,0.781 0.156,0.156 10 false 1 3.177,0.615 3.333,0.771 0.156,0.156 10 false 2 1.646,1.521 1.802,1.677 0.156,0.156 10 false 3 2.406,0.073 2.563,0.229 0.156,0.156 10 false 4 1.646,1.031 1.802,1.188 0.156,0.156 10 false 5 0.344,1.292 0.5,1.448 0.156,0.156 10 false 1 1.292,1.281 1.448,1.438 0.156,0.156 10 false 2 0.333,0.76 0.49,0.917 0.156,0.156 10 false 3 0.896,0.406 1.052,0.563 0.156,0.156 10 false 4 1.292,0.76 1.448,0.917 0.156,0.156 10 false 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Battery voltage not applied to terminals 1 and 2
Measurement temperature : 20 °C
93.8 to 136.4 kΩ
3 - 4 Battery voltage not applied to terminals 1 and 2 Below 1 Ω
Battery voltage applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the starter relay.


Hide 4.INSPECT IGS RELAY

a.
B453162E01
1.729,0.729 1.99,0.729 true 2.646,0.729 2.906,0.729 true 2.521,1.104 2.927,1.104 true 2.531,1.594 2.938,1.594 true 0.25,0.76 0.406,0.958 0.156,0.198 10 false 3 1.198,0.75 1.354,0.948 0.156,0.198 10 false 5 0.25,1.271 0.406,1.469 0.156,0.198 10 false 1 1.198,1.281 1.354,1.479 0.156,0.198 10 false 2 1.573,0.656 1.729,0.854 0.156,0.198 10 false 1 3.01,0.635 3.167,0.833 0.156,0.198 10 false 2 3.01,1 3.167,1.198 0.156,0.198 10 false 5 3.01,1.5 3.167,1.698 0.156,0.198 10 false 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Battery voltage not applied to terminals 1 and 2
Measurement temperature : 20 °C
93.8 to 136.4 kΩ
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the starter relay.