Home › Engine / Hybrid System › FA20 STARTING › STARTER(for Automatic Transmission)
RM2090E _51 Engine / Hybrid System _060672 FA20 STARTING _0297538 STARTER(for Automatic Transmission) G

FA20 STARTING  STARTER(for Automatic Transmission)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

The following tests must each be performed within 3 to 5 seconds to prevent the coil from burning out.


a.

Mount the starter in a vise between aluminum plates.


b.

Perform a pull-in test.

i.

Remove the nut, and then disconnect the lead wire from terminal C.


ii.
A282564E03
1.104,0.635 0.917,0.354 true 1.813,0.583 2,0.365 true 2.406,1.031 1.938,0.844 true 0.802,0.188 0.958,0.365 0.156,0.177 10 false *1 1.948,0.198 2.104,0.375 0.156,0.177 10 false *2 2.458,0.958 2.615,1.135 0.156,0.177 10 false *3

Connect the battery to the starter as shown in the illustration. Check that the clutch pinion gear extends.

Text in Illustration
*1 Body
*2 Terminal 50
*3 Terminal C

If the clutch pinion gear does not move, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



c.

Perform a holding test.

i.
A282565E03
1.115,0.625 0.854,0.354 true 2.135,0.354 1.813,0.594 true 2.396,1.042 1.927,0.844 true 0.698,0.229 0.854,0.406 0.156,0.177 10 false *1 2.156,0.24 2.313,0.417 0.156,0.177 10 false *2 2.438,0.979 2.594,1.156 0.156,0.177 10 false *3

Disconnect the negative (-) terminal lead from terminal C while the conditions specified in the pull-in test above are maintained. Check that the pinion gear remains out.

Text in Illustration
*1 Body
*2 Terminal 50
*3 Terminal C

If the clutch pinion gear returns inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



d.

Inspect the clutch pinion gear return.

i.
A282566E03
1.094,0.646 0.885,0.344 true 1.813,0.583 2.021,0.354 true 2.323,1.01 1.927,0.844 true 0.781,0.177 0.938,0.354 0.156,0.177 10 false *1 2.031,0.208 2.188,0.385 0.156,0.177 10 false *2 2.385,0.948 2.542,1.125 0.156,0.177 10 false *3

Disconnect the negative (-) terminal lead from the starter body. Check that the clutch pinion gear returns inward.

Text in Illustration
*1 Body
*2 Terminal 50
*3 Terminal C

If the clutch pinion gear does not return inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



e.

Perform an operation test without load.

i.

Connect the lead wire to terminal C with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.
A282567E03
0.604,1.896 1.042,2 true 2.344,0.177 2.208,0.365 true 2.417,0.406 2.781,0.385 true 2.313,0.021 2.469,0.198 0.156,0.177 10 false *1 2.844,0.302 3,0.479 0.156,0.177 10 false *2 1.083,1.938 1.24,2.115 0.156,0.177 10 false *3

Connect the battery and an ammeter to the starter as shown in the illustration.

Text in Illustration
*1 Terminal 50
*2 Terminal 30
*3 Ammeter


iii.

Check that the starter rotates smoothly and steadily while the clutch pinion gear is extended. Then measure the current.

Standard Current:
Tester Connection Condition Specified Condition
Battery positive terminal - Terminal 30 - Terminal 50 11.5 V Below 90 A


If the result is not as specified, inspect the starter assembly.

HINT:

Inspect the starter armature assembly, starter commutator end frame assembly and magnet starter switch assembly. If there is a malfunction, replace the part and perform again this test.




Hide 28160 2.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator for dirt and/or burns on the surface.

If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe. If necessary, replace the starter armature assembly.


b.

Inspect the commutator for an open circuit.

i.
U137220E02
0.927,1.677 1.083,1.833 0.156,0.156 10 false *1

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*1 Segment

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



c.

Inspect the commutator for short circuits.

i.
A082644E16
1.531,1.813 1.604,1.813 1.604,1.813 1.99,1.427 true 0.594,1.365 0.656,1.365 0.656,1.365 1.115,1.01 true 1.323,1.75 1.479,1.896 0.156,0.146 10 false *1 0.396,1.281 0.646,1.51 0.25,0.229 10 false *2

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*1 Segment
*2 Coil Core

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Coil core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



d.

Check the commutator for signs of seizure or stepped wear caused by roughness of the surface. If there is light wear, use sandpaper to repair.


e.
A082645E04
1.979,0.646 2.552,0.354 true 0.771,1.51 0.427,1.792 0.427,1.792 1.74,1.969 true 2.615,0.26 2.771,0.438 0.156,0.177 10 false *1 0.219,1.708 0.375,1.885 0.156,0.177 10 false *2

Check for runout on the commutator. If excessive, replace the armature.

Standard runout:

0.02 mm (0.0008 in.)


Maximum runout:

0.05 mm (0.002 in.)


Text in Illustration
*1 Dial Gauge
*2 V-block

If the result is not as specified, replace the starter armature assembly.


f.
A062221E04
0.24,0.083 0.396,0.26 0.156,0.177 10 false *a

Using vernier caliper, measure the commutator diameter.

Text in Illustration
*a Diameter

Standard diameter:

29 mm (1.1417 in.)


Minimum diameter:

28 mm (1.1024 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


g.
A062965

Using vernier caliper, measure the under cut depth of the segment. If it is not within the standard, replace the starter armature assembly.

Standard depth:

0.7 mm (0.0276 in.)


Minimum depth:

0.2 mm (0.0079 in.)



Hide 28140 3.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A204349E02
2.723,0.174 2.879,0.355 0.156,0.181 10 *a

Using a vernier caliper, measure the brush length.

Text in Illustration
*a Length

Standard length:

14.4 mm (0.5669 in.)


Minimum length:

9.0 mm (0.3543 in.)


If the length is less than the minimum, replace the starter brush holder assembly.


b.
A095705E16
1.021,1.156 0.51,0.979 true 1.344,1.781 0.885,1.917 true 2.5,1.146 2.802,1.146 true 2.125,0.49 2.417,0.198 true 0.344,0.875 0.458,1.031 0.115,0.156 10 false A 0.74,1.854 0.854,2.01 0.115,0.156 10 false B 2.865,1.063 2.99,1.219 0.125,0.156 10 false C 2.49,0.083 2.604,0.24 0.115,0.156 10 false D

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A - B
A - C
B - D
C - D
Always 10 kΩ or higher
A - D
B - C
Always Below 1 Ω


If the result is not as specified, replace the starter brush holder assembly.


Hide 28150 4.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.

Check the plunger.

i.
A033580

Push in the plunger and check that it returns quickly to it is original position.

If necessary, replace the magnet starter switch assembly.



b.

Inspect the pull-in coil.

i.
A282561E02
1.604,0.688 1.125,0.229 true 1.802,0.594 2.438,0.219 true 2.479,0.104 2.635,0.281 0.156,0.177 10 false *1 0.948,0.073 1.104,0.25 0.156,0.177 10 false *2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal C - Terminal 50 Always Below 1 Ω


Text in Illustration
*1 Terminal C
*2 Terminal 50

If the result is not as specified, replace the magnet starter switch assembly.



c.

Inspect the holding coil.

i.
A282562E02
1.188,0.25 1.594,0.688 true 1.969,1.094 2.635,1.271 true 1.01,0.104 1.167,0.281 0.156,0.177 10 false *1 2.708,1.208 2.865,1.385 0.156,0.177 10 false *2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Switch body Always Below 2 Ω


Text in Illustration
*1 Terminal 50
*2 Switch Body

If the result is not as specified, replace the magnet starter switch assembly.