Home › Engine / Hybrid System › FA20 STARTING › STARTER(for Automatic Transmission)
RM2090E _51 Engine / Hybrid System _060672 FA20 STARTING _0297538 STARTER(for Automatic Transmission) A

FA20 STARTING  STARTER(for Automatic Transmission)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STARTER PLANETARY GEAR

A282563

a.

Apply high-temperature grease to the planetary gears and pins of the planetary shaft.


b.

Install the 3 starter planetary gears.

Text in Illustration
V100135

High-temperature Grease


Hide 2.INSTALL RUBBER SEAL

a.
A281407E03
1.302,0.875 1.479,0.365 true 1.448,0.177 1.604,0.354 0.156,0.177 10 false *1

Install the rubber seal to the starter drive housing assembly.

Text in Illustration
*1 Rubber Seal


Hide 28160 3.INSTALL STARTER ARMATURE ASSEMBLY

a.
A281405E02
1.156,0.688 0.74,0.271 true 1.49,1.427 0.729,1.896 true 0.542,0.146 0.698,0.323 0.156,0.177 10 false *1 0.531,1.844 0.688,2.021 0.156,0.177 10 false *2

Install the starter armature assembly to the starter yoke assembly.

Text in Illustration
*1 Starter Yoke Assembly
*2 Starter Armature Assembly


Hide 28140 4.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A211303

Install the 4 brushes and 4 brush springs.


b.
A211304

Install the starter brush holder assembly to the starter armature assembly. Push the 4 brushs.


c.
A194294E03
1.573,1.156 1.01,1.51 true 2.313,0.948 3.031,1.396 true 1.865,0.958 0.948,0.49 true 3.115,1.365 3.333,1.563 0.219,0.198 10 false *3 0.813,1.521 1.104,1.74 0.292,0.219 10 false *2 0.74,0.344 0.969,0.542 0.229,0.198 10 false *1

Insert the grommet between the positive (+) motor read wire and the negative (-) brush holder plate.

Text in Illustration
*1 Grommet
*2 Negative (-) Brush Holder Plate
*3 Positive (+) Motor Read Wire


Hide 28199 5.INSTALL STARTER COVER

a.

Install the dust starter protector to the starter yoke assembly.


b.
A190520

Align the starter brush holder assembly read wire rubber with the groove of the starter cover.


c.
A192615

Install the starter cover to the starter brush holder assembly with 2 screws.

Torque:
: 1.5 N*m (15 kgf*cm, 13 in.*lbf)


Hide 6.INSTALL STARTER ARMATURE PLATE

a.

Align the claw of the starter yoke assembly with the groove the starter armature plate.


b.

Install the starter armature plate to the starter yoke assembly.

A187232E08
2.917,1.5 3.208,1.573 false 2.073,1.313 1.979,1.5 true 5.5,0.542 5.792,1.135 5.792,1.135 5.073,1.281 true 5.469,1.021 5.792,1.135 true 5.01,0.25 4.323,0.323 4.323,0.323 4.583,1 true 4.615,0.521 4.323,0.323 true 1.865,1.521 2.021,1.688 0.156,0.167 10 false *1 3.271,1.5 3.427,1.667 0.156,0.167 10 false *2 5.844,1.052 6,1.219 0.156,0.167 10 false *1 4.104,0.208 4.26,0.375 0.156,0.167 10 false *1

Text in illustration
*1 Claw *2 Groove


Hide 28120 7.INSTALL STARTER YOKE ASSEMBLY

a.
A172145E04
1.823,1.552 1.958,1.792 false 2.646,1.344 2.76,1.688 true 1.917,1.813 2.073,1.99 0.156,0.177 10 false *1 2.708,1.708 2.865,1.885 0.156,0.177 10 false *2

Align the claw of the starter yoke assembly with the groove inside the starter drive housing assembly.

Install the starter yoke assembly together with the starter armature assembly to the starter drive housing assembly.

Text in Illustration
*1 Claw
*2 Groove


b.
A280973

Using a "TORX" socket wrench T25, install the 2 through bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 28150 8.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.
A281422

Apply high-temperature grease to the plunger and hook as shown in the illustration.

Text in Illustration
V100135

High-temperature grease


b.
A156359E03
0.896,0.802 0.948,0.323 true 1.281,0.698 1.26,0.344 true 1.188,0.167 1.344,0.344 0.156,0.177 10 false *1 0.875,0.156 1.031,0.333 0.156,0.177 10 false *2

Hook the plunger and hook of the magnet starter switch assembly to the lever of the starter drive housing assembly.

Text in Illustration
*1 Plunger and Hook
*2 Lever


c.
A280972

Install the magnet starter switch assembly with the 2 screws.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.
A280971

Connect the lead wire to terminal C with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)