Home › Engine / Hybrid System › FA20 STARTING › STARTER(for Manual Transmission)
RM2090E _51 Engine / Hybrid System _060672 FA20 STARTING _0297539 STARTER(for Manual Transmission) G

FA20 STARTING  STARTER(for Manual Transmission)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

The following tests must each be performed within 3 to 5 seconds to prevent the coil from burning out.


a.

Mount the starter in a vise between aluminum plates.


b.

Perform a pull-in test.

i.

Remove the nut, and then disconnect the lead wire from terminal C.


ii.
A282564E03
1.104,0.635 0.917,0.354 true 1.813,0.583 2,0.365 true 2.406,1.031 1.938,0.844 true 0.802,0.188 0.958,0.365 0.156,0.177 10 false *1 1.948,0.198 2.104,0.375 0.156,0.177 10 false *2 2.458,0.958 2.615,1.135 0.156,0.177 10 false *3

Connect the battery to the starter as shown in the illustration. Check that the clutch pinion gear extends.

Text in Illustration
*1 Body
*2 Terminal 50
*3 Terminal C

If the clutch pinion gear does not move, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



c.

Perform a holding test.

i.
A282565E03
1.115,0.625 0.854,0.354 true 2.135,0.354 1.813,0.594 true 2.396,1.042 1.927,0.844 true 0.698,0.229 0.854,0.406 0.156,0.177 10 false *1 2.156,0.24 2.313,0.417 0.156,0.177 10 false *2 2.438,0.979 2.594,1.156 0.156,0.177 10 false *3

Disconnect the negative (-) terminal lead from terminal C while the conditions specified in the pull-in test above are maintained. Check that the pinion gear remains out.

Text in Illustration
*1 Body
*2 Terminal 50
*3 Terminal C

If the clutch pinion gear returns inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



d.

Inspect the clutch pinion gear return.

i.
A282566E03
1.094,0.646 0.885,0.344 true 1.813,0.583 2.021,0.354 true 2.323,1.01 1.927,0.844 true 0.781,0.177 0.938,0.354 0.156,0.177 10 false *1 2.031,0.208 2.188,0.385 0.156,0.177 10 false *2 2.385,0.948 2.542,1.125 0.156,0.177 10 false *3

Disconnect the negative (-) terminal lead from the starter body. Check that the clutch pinion gear returns inward.

Text in Illustration
*1 Body
*2 Terminal 50
*3 Terminal C

If the clutch pinion gear does not return inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



e.

Perform an operation test without load.

i.

Connect the lead wire to terminal C with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.
A282567E03
0.604,1.896 1.042,2 true 2.344,0.177 2.208,0.365 true 2.417,0.406 2.781,0.385 true 2.313,0.021 2.469,0.198 0.156,0.177 10 false *1 2.844,0.302 3,0.479 0.156,0.177 10 false *2 1.083,1.938 1.24,2.115 0.156,0.177 10 false *3

Connect the battery and an ammeter to the starter as shown in the illustration.

Text in Illustration
*1 Terminal 50
*2 Terminal 30
*3 Ammeter


iii.

Check that the starter rotates smoothly and steadily while the clutch pinion gear is extended. Then measure the current.

Standard Current:
Tester Connection Condition Specified Condition
Battery positive terminal - Terminal 30 - Terminal 50 11.5 V Below 90 A


If the result is not as specified, inspect the starter assembly.

HINT:

Inspect the starter armature assembly, starter commutator end frame assembly and magnet starter switch assembly. If there is a malfunction, replace the part and perform again this test.




Hide 28160 2.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator for signs of seizure or stepped wear caused by roughness of the surface. If there is light wear, use sandpaper to repair.


b.
A279743E03
2.656,1.833 3.031,1.833 true 1.646,0.479 2.125,0.281 true 2.177,0.156 2.333,0.333 0.156,0.177 10 false *1 3.104,1.74 3.26,1.917 0.156,0.177 10 false *2

Check for runout on the commutator. If excessive, replace the armature.

Standard runout:

0.05 mm (0.002 in.)


Maximum runout:

0.10 mm (0.004 in.)


Text in Illustration
*1 Dial Gauge
*2 V-block


c.
A279744E02
1.115,0.771 1.01,0.281 true 1.969,0.75 2.083,0.26 true 0.927,0.094 1.083,0.271 0.156,0.177 10 false *1 2.021,0.083 2.177,0.26 0.156,0.177 10 false *2 2.354,1.49 2.51,1.667 0.156,0.177 10 false *3

Check the depth of the segment mold. If it is not within the standard, replace the armature.

Standard depth:

0.50 mm (0.020 in.)


Text in Illustration
*1 Mold
*2 Segment
*3 Depth of Mold


d.
A279745E02
1.615,0.792 1.833,0.344 true 2.385,1.281 2.604,0.833 true 1.792,0.188 1.948,0.365 0.156,0.177 10 false *1 2.573,0.667 2.729,0.844 0.156,0.177 10 false *2

Place the armature on the growler tester to check for short circuits. While slowly turning the armature, support the steel sheet for the armature core. If the circuit of the armature is shorted, the steel sheet will vibrate, causing it to move towards the core. When the steel sheet has moved or vibrated, replace the armature.

Text in Illustration
*1 Steel Sheet
*2 Growler Tester


e.
A279746

Touch the probe of one side to the commutator segment, and the other probe to the shaft. If there is continuity, replace the armature.


Hide 28120 3.INSPECT STARTER YOKE ASSEMBLY

a.

Make sure that the pole is set at the predetermined position.


Hide 28140 4.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.

Visually check the brush. If there is any abnormal wear or cracks, replace the brush.


b.
A398078E01
2.292,1.521 2.885,1.396 true 2.938,0.833 3.25,1.031 0.313,0.198 10 false *1 2.958,1.292 3.271,1.49 0.313,0.198 10 false *2

Measure the length of the brush. If it exceeds the service limits, replace the brush.

Standard length:

12.3 mm (0.484 in.)


Minimum length:

7.0 mm (0.276 in.)


Text in Illustration
*1 Service Limit Line
*2 Brush


c.

Check that the brush moves smoothly in the brush holder.


d.

Measure the brush spring force with a spring scale. Replace the brush holder if below the service limit.

Standard brush spring force:

15.9 to 19.5 N (1.6 to 2.0 kgf, 3.6 to 4.4 lbf)


Minimum brush spring force:

2.5 N (0.3 kgf, 0.6 lbf)



Hide 28011 5.INSPECT STARTER CLUTCH SUB-ASSEMBLY

a.

Check the gear teeth on the planetary gear, internal gear and starter clutch for wear or damage.

If any of the gears is damaged, replace the starter center bearing clutch sub-assembly.


b.

Check the starter clutch pinion gear.

i.
A275510E02
1.823,0.49 2,0.656 0.177,0.167 10 false *a 1.583,1.448 1.76,1.615 0.177,0.167 10 false *b

Hold the starter clutch, rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

Text in Illustration
*a Free
*b Lock

If necessary, replace the starter clutch sub-assembly.



Hide 28150 6.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.
A279748E03
0.844,1.031 0.438,1.188 true 2.104,0.354 1.469,0.656 true 1.604,1.844 1.469,1.406 true 2.167,0.25 2.323,0.427 0.156,0.177 10 false *3 1.542,1.885 1.698,2.063 0.156,0.177 10 false *2 0.25,1.125 0.406,1.302 0.156,0.177 10 false *1

Check that there is continuity between terminals 50 and C, and between terminal 50 and ground. Also, check to be sure there is no continuity between terminal C and 30.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal C - Terminal 50 Always Below 1 Ω
Terminal 50 - Switch body Always Below 1 Ω
Terminal C - Terminal 30 Always 1 MΩ or higher


Text in Illustration
*1 Terminal 50
*2 Terminal C
*3 Terminal 30


b.

Using a lead wire, connect the switch assembly terminal 50 to the positive terminal of the battery, and the starter body to the ground terminal of the battery. The pinion should be forced to be pushed out on the shaft.

HINT:

With the pinion forced to be pushed out on the shaft, the starter motor can sometimes rotate because the current flows, through pull-in coil, to motor. This is not a problem.



c.
A279749E03
1.594,0.167 2.625,0.167 true 1.427,0.396 0.594,0.656 true 2.677,0.083 2.833,0.26 0.156,0.177 10 false *1 0.406,0.594 0.563,0.771 0.156,0.177 10 false *2

Disconnect the connector from terminal C. Then, using a lead wire, connect the positive terminal of the battery and terminal C, and ground terminal to starter body. In this test set up, the pinion should return to its original position even when it is pulled out with a screwdriver.

Text in Illustration
*1 Terminal 50
*2 Terminal C