Home › Engine / Hybrid System › FA20 STARTING › STARTER(for Manual Transmission)
RM2090E _51 Engine / Hybrid System _060672 FA20 STARTING _0297539 STARTER(for Manual Transmission) A

FA20 STARTING  STARTER(for Manual Transmission)  DISASSEMBLY  


PROCEDURE

Hide 28150 1.REMOVE MAGNET STARTER SWITCH ASSEMBLY

a.
A281409

Remove the nut and disconnect the lead wire from terminal C.


b.
A281410

Remove the 2 screws and the magnet starter switch assembly from the starter drive housing assembly.


Hide 28199 2.REMOVE STARTER COVER

a.
A281411

Remove the 2 through bolts and 2 screws, and remove the starter cover.


Hide 28140 3.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A281412

Remove the starter brush holder assembly.

HINT:

Hold the brush with your fingers so that the brush spring does not come flying out.



Hide 28120 4.REMOVE STARTER YOKE ASSEMBLY

a.
A281413

Remove the starter yoke assembly and starter armature assembly together from the starter drive housing assembly.


Hide 28160 5.REMOVE STARTER ARMATURE ASSEMBLY

a.
A281414

Pull out the starter armature assembly from the starter yoke assembly.


Hide 6.REMOVE STARTER HOUSING RUBBER

a.
A281416E03
1.302,0.625 0.74,0.323 true 2.458,0.385 1.688,0.802 true 1.448,1.615 0.781,1.771 true 0.542,0.219 0.698,0.396 0.156,0.177 10 false *1 2.531,0.26 2.688,0.438 0.156,0.177 10 false *2 0.583,1.708 0.74,1.885 0.156,0.177 10 false *3

Remove the starter housing rubber, seal rubber and plate from the starter drive housing assembly.

Text in Illustration
*1 Starter Housing Rubber
*2 Plate
*3 Seal Rubber


Hide 7.REMOVE STARTER PLANETARY GEAR

a.
A281408

Remove the 3 starter planetary gears from the starter clutch sub-assembly.


Hide 28011 8.REMOVE STARTER CLUTCH SUB-ASSEMBLY

a.
A281417

Remove the starter clutch sub-assembly together with the drive lever set pin from the starter drive housing assembly.


b.
A278479E02
2.677,0.479 2.885,0.479 true 2.667,0.792 2.875,0.729 true 2.625,0.813 2.885,0.958 true 2.927,0.396 3.083,0.552 0.156,0.156 10 false *1 2.917,0.646 3.073,0.802 0.156,0.156 10 false *2 2.938,0.906 3.094,1.063 0.156,0.156 10 false *3

Using a 14 mm deep socket wrench, remove the stopper from snap ring.

Text in Illustration
*1 14 mm Deep Socket Wrench
*2 Stopper
*3 Snap Ring


c.
A281418

Using snap ring pliers, remove the snap ring and stopper.


d.
A281419

Pull out the over running clutch from the shaft.


e.
A281420E02
2.281,1.854 2.823,2.313 true 1.865,3.135 2.792,2.979 true 2.885,2.313 3.042,2.49 0.156,0.177 10 false *1 2.875,2.885 3.031,3.063 0.156,0.177 10 false *2

Remove the internal gear assembly from the shaft.

Text in Illustration
*1 Internal Gear Assembly
*2 Shaft